copymaster3D Voron Trident User manual

81
WWW.VORONDESIGN.COM
TOOL CARTRIDGE
Heat Set Insert
E3D V6 Style Hotend
M3x16 SHCS
AVAILABLE MOUNTS
We also provide mounts for the
Slice Engineering Mosquito and
TriangleLab/Phaetus Dragon
Hotend.
They are assembled in a similar
manner.
www.copymaster3d.com
[e-mail]

82
WWW.VORONDESIGN.COM
TOOL CARTRIDGE
M3x40 SHCS
PT FE Tube
PTFE STICKOUT
The PTFE tube should end 10mm
above the surface of the printed
part.
www.copymaster3d.com
[e-mail]

83
WWW.VORONDESIGN.COM
TOOL CARTRIDGE
www.copymaster3d.com
[e-mail]

84
WWW.VORONDESIGN.COM
CLOCKWORK
Heat Set Insert
www.copymaster3d.com
[e-mail]

85
WWW.VORONDESIGN.COM
CLOCKWORK
BMG Drive Pinion
Stepper Motor
M3x8 SHCS
M3x8 SHCS
STEPPER WIRES
If the steppers has wires cut them
to approximately 150mm.
Wires/connector to the right hand
side.
www.copymaster3d.com
[e-mail]

86
WWW.VORONDESIGN.COM
CLOCKWORK
Heat Set Insert
BMG Idler Assembly
BMG Thumb Screw
LUBRICATE BEARINGS
A light lubrication lm will help with
smooth operation and longevity.
www.copymaster3d.com
[e-mail]

87
WWW.VORONDESIGN.COM
CLOCKWORK
BMG Drive Assembly
CHECK BEARING FIT
The bearings must slip on and off the shaft
easily. Pressing the bearings on the shaft
will damage them. Lightly sand the shaft if
required.
www.copymaster3d.com
[e-mail]

88
WWW.VORONDESIGN.COM
CLOCKWORK
M3x30 SHCS
www.copymaster3d.com
[e-mail]

89
WWW.VORONDESIGN.COM
CLOCKWORK
M3x20 SHCS
www.copymaster3d.com
[e-mail]

90
WWW.VORONDESIGN.COM
CLOCKWORK
PT FE Tube
M3x6 BHCS
www.copymaster3d.com
[e-mail]

91
WWW.VORONDESIGN.COM
CLOCKWORK
M3x30 SHCS M3x20 SHCS
www.copymaster3d.com
[e-mail]

92
WWW.VORONDESIGN.COM
FAN ASSEMBLY
M3x16 SHCS
DON’T OVER TIGHTEN
The screws are screwd
directly into plastic.
REMOVE TOP COVER
Split the fan open by
bending the taps on the
side.
www.copymaster3d.com
[e-mail]

93
WWW.VORONDESIGN.COM
FAN ASSEMBLY
Piece of Filament
www.copymaster3d.com
[e-mail]

94
WWW.VORONDESIGN.COM
FAN ASSEMBLY
M3x12 SHCS
M3x30 SHCS
www.copymaster3d.com
[e-mail]

95
WWW.VORONDESIGN.COM
This page intentionally left blank.
www.copymaster3d.com
[e-mail]

96
WWW.VORONDESIGN.COM
PRINT BED & WIRE PATH
www.copymaster3d.com
[e-mail]

97
WWW.VORONDESIGN.COM
SOLDER WIRES
Solder 500mm of wire to the microswitch
before inserting it ush into the housing.
PRELOADED NUTS
The nuts have been installed several chapters before.
Y ENDSTOP
Microswitch
M3x16 SHCS
M5x16 BHCS
www.copymaster3d.com
[e-mail]

98
WWW.VORONDESIGN.COM
REMOVE FLANGE & GRUB SCREWS
Use a bottle opener or some pliers to
remove the top ange.
Remove the grub screws from the
pulley.
PRESS FIT
Apply the required force to fully
seat the pulley in the printed
part.
Z ENDSTOP
GT2 Pulley
Microswitch
M2x10 Self Tapping
SOLDER WIRES
Solder 100mm of wire to the
microswitch before inserting it into
the housing.
www.copymaster3d.com
[e-mail]

99
WWW.VORONDESIGN.COM
Z ENDSTOP
5mm Shaft
M3x20 SHCS
www.copymaster3d.com
[e-mail]

100
WWW.VORONDESIGN.COM
CABLE CHAIN
M3x6 BHCS
FIXED END VS. FREE END
Some cable chains only have one end that is
able to swing freely. Use this end on the back
of the Afterburner.
www.copymaster3d.com
[e-mail]