CORNING CWDM MUX User manual

STANDARD RECOMMENDED PROCEDURE 003-787 | ISSUE 1 | AUGUST 2008 | PAGE 1 OF 2
| PRETERMINATED SYSTEMS | CABLES | CONNECTORS | CABLE ASSEMBLIES | HARDWARE | TOOL KITS AND ACCESSORIES | TEST EQUIPMENT | SPLICE EQUIPMENT | FAN-OUT KITS | TRAINING |
=
Enhanced Management
Frame CWDM MUX / DEMUX
Modules
p/n 003-787, Issue 1
1. General
WARNING: Never look directly into the end of a fiber that may be carrying
laser light. Laser light is invisible and can damage your eyes. Viewing it directly
does not cause pain. The iris of the eye will not close involuntarily as when
viewing a bright light. Consequently, serious damage to the retina of the eye is
possible. Should accidental eye exposure to laserlight be suspected, arrange for
an eye examination immediately.
This document describes the recommended procedure
for installing CWDM MUX / DEMUX modules into the
Enhanced Management Frame (EMF). This procedure
assumes that the housing assembly has already been
installed into the frame per the instructions provided
with the housing.
2. Install CWDM Modules
Step 1: Determine the location for installation of the
module.
Step 2: Slide the module into the slot as shown in
Figure 1.
Step 3: Refer to the designation label attached to the
handle to verify you are installing the
appropriate module for your application (Figure 2).
revision history |
Issue Date Reason for Change
1 08/2008 Initial release
related literature |
003-580 Enhanced Management Frame — Housing Installation
003-599 Jumper Routing in Enhanced Management Frame
KPA-2132
M.
MUX N/A COM MON 1310 1471 1491 1511 1531 1571 1591 1611
1551
Figure 1 — Install Splitter Module
M.
MUX N/A COM MON 1310 1471 1491 1511 1531 1571 1591 1611
M.
DEMUX N/A COM MON 1310 1471 1491 1511 1531
1551
1551 1571 1591 1611
KPA-2131
Figure 2 — Port Designations

STANDARD RECOMMENDED PROCEDURE 003-787 | ISSUE 1 | AUGUST 2008 | PAGE 2 OF 2
Corning Cable Systems LLC √PO Box 489 √Hickory, NC 28603-0489 USA
1-800-743-2671 √FAX [phone] √International [phone] √http://www.corning.com/cablesystems
Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems’ products without prior notification.
All trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001 certified.
©2008 Corning Cable Systems. All rights reserved. Published in the USA.
=
3. Connect Jumpers to CWDM Modules
Step 1: Pull module out to detent position (Figure 3).
Step 2: Press buttons on each side of the module (Figure 4) and lower the handle.
Step 3: Remove dust caps and clean adapters and connectors per standard company practice.
Step 4: Refer to the designation label (Figure 2) on the handle of the module for the port
designations to determine where your jumpers should be connected.
NOTE: The first port on the left is empty and not available for use.
• Connect the common port jumper to the port labeled “COM.”
• Connect the remaining jumpers to the applicable port with the desired wavelength as
shown on the designation label.
• To monitor the module, insert a test jumper into the port labeled “MON.”
Step 5: Connect jumpers (Figure 5) as required.
Step 6: Raise handle. Dress jumper cords (Figure 6) to the side of the module.
Step 7: Push module back into the housing and dress jumper cords in frame as described in the
installation instruction provided with the housing.
IMPORTANT: Guide fibers while inserting module to avoid pinching fibers.
KPA-2135
Button
M.
MUX N/A
COM
MON 1310 1471 1491 1511 1531 1571 1591 1611
1551
Figure 4 — Lower Handle
KPA-2134
M.
MUX N/A
COM
MON 1310 1471 1491 1511 1531 1571 1591 1611
1551
Figure 3 — Pull Module Out
11
10
4
3
2
16
5
MON 1471
KPA-2137
MUX MON 1310 1471 1491 1511 1531 1551 1571 1591 1611
COM
N/A
MUX 1310
N/A
Figure 6 — Dress Jumper Cords
12
11
17
10
9
4
3
2
18
7
6
5
N/A
MUX
MUX
MON 1310 1491 1511 1531 1551 1571 1591 1611
COM
KPA-2136
Figure 5 — Connect Jumpers