CORNING CCH-CS User manual

p/n 003-895, Issue 1
STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 1 OF 11
| PRETERMINATED SYSTEMS | CABLES | CONNECTORS | CABLE ASSEMBLIES | HARDWARE | TOOL KITS AND ACCESSORIES | TEST EQUIPMENT | SPLICE EQUIPMENT | FAN-OUT KITS | TRAINING
Splice Cassette (CCH-CS)
and Slack Cassette (CCH-CF)
for Closet Connector
Housings
related literature |
003-876-QSG Closet Connector Housing (CCH) 1U/2U/3U Quick Start Guide
003-876 Instruction, Closet Connector Housing (CCH) 1U/2U/3U
003-877-QSG Closet Connector Housing (CCH) 4U Quick Start Guide
003-877 Instruction, Closet Connector Housing (CCH) 4U
1. Precautions
WarninG: 
 Laser light can be invisible and can damage your eyes. Viewing it directly does not
cause pain. The iris of the eye will not close involuntarily as when viewing a bright light.
Consequently, serious damage to the retina of the eye is possible. Should accidental eye
exposure to laser light be suspected, arrange for an eye examination immediately.
WarninG: DO NOT use magniers in the presence of laser radiation. Diffused laser
light can cause eye damage if focused with optical instruments. Should accidental eye
exposure to laser light be suspected, arrange for an eye examination immediately.
caution: Recommend the use of safety glasses (spectacles) conforming to ANSI Z87,
for eye protection from accidental injury when handling chemicals, cables, or working with
ber. Pieces of glass ber are very sharp and have the potential to damage the eye.
caution: The wearing of cut-resistant safety gloves to protect your hands from
accidental injury when using sharp-bladed tools and armored cable is strongly
recommended. Use extreme care when working with severed armor. There will be a
sharp edge where armor is cut. To minimize the chance of injury from the cut armor,
cover the exposed edge with a wrap of electrical tape. To minimize the chance of injury
from sharp-bladed tools, always cut away from yourself and others. Dispose of used
blades and armor scrap properly.
Table of Contents
  ................................................................ 1
  ............ 2
  ............................. 5
  ........... 9
  ................... 9
 
 ................................................... 
  ..........................................11

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 2 OF 11
caution: Cleaved or broken glass bers are very sharp and can pierce the skin easily.
Do not let these pieces of ber stick to your clothing or drop in the work area where they
can cause injury later. Use tweezers to pick up cleaved or broken pieces of glass bers
and place them on a loop of tape kept for that purpose alone. 

2. 

2.1. 
12
TPA-3928
TPA-3929
3
27 inches
4

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 3 OF 11
2.2. 
TPA-3930
5
TPA-3931
6
7
8
TPA-3932
9
10
62 inches 48 inches
82 inches 48 inches
Strip Lengths
for Splicing
Strain-relief
Point
TPA-3951
1U/2U/3U Housing
4U Housing
110 inches
130 inches

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 4 OF 11
2.3. 
Cut to:
48 inches (250 micron)
35 inches (900 micron)
1
2
3
TPA-3933
5
6
4
TPA-3934
Repeat Step 5
on the other side of
cassette. Loop
and store all fiber
under flanges.
Fold fiber over
into cassette
and store under
flanges.
Cover
7
89
TPA-3935
Close cover.

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 5 OF 11
Loose Tube Fiber
Tight-buffer Fiber
Protect tight-buffer fiber with braided tubing, if
needed, for multiple cables or 24-fiber cables.
TPA-3950
10 Store up to 38 inches of cable slack under cassette.
3. 
3.1. 
35 inches
Ribbon Pigtail
TPA-3936
Protective tubing is required
for ribbon splicing application.
NOTE: Ensure length of pigtail is
approximately 35 inches
from fan-out body.
9 inches
Ribbon Pigtail
TPA-3937
1Cut 9 inches of protective tubing.
2
CRITICAL STEP:
Slide tubing onto ribbon
up to the fan-out body.

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 6 OF 11
12
TPA-3928
TPA-3938
56
7
Capture fibers and
ribbon under flanges.
TPA-3939
TPA-3839
8
10
Press plungers
to install
adapter panel.
9
Ensure slack
is properly
managed.

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 7 OF 11
3.2. 
NOTE: Rotate splice organizer 90-degrees from its factory-installed orientation meant for single bers
to the orientation shown for ribbon ber splices.
3.3. 
Single-fiber Orientation Mass Fusion Ribbon Orientation
TPA-3949
90°
TPA-3940
TPA-3840
1
4
2
Rotate splice organizer
90° for ribbon storage.
3
Flex organizer to
reinstall.
Organizer installed
in orientation for
ribbon storage.
62 inches 48 inches
82 inches 48 inches
Strip Lengths
for Splicing
Strain-relief
Point
TPA-3951
1U/2U/3U Housing
4U Housing
110 inches
130 inches

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 8 OF 11
TPA-3941
5
68
7
Bring pigtail ribbon from
bottom layer into top layer.
Slide heatshrink tube
onto ribbon up to jacket.
Route as
shown.
10
9
Apply heat to heatshrink tube.
Route ribbon
to bottom layer.
11
12
13
Place ribbons in tube;
secure with cable tie.
Route as
shown.
Splice per the
instructions
provided with
the splice
equipment.
Cut ribbons in center of
organizer.
TPA-3942
16
17
18
15
14
Store heatshrink tube
in splice organizer.
Route as
shown.
Store heatshrink tubing
in splice organizer.
Store ribbon in
slack storage area
on bottom layer.
Close cover.
Loosely secure ribbon with cable tie.

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 9 OF 11
4. 

5. 

TPA-3946

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 10 OF 11
6. 

TPA-3943
Slide covers
apart to
remove.
Remove:
Open front and
back doors. 8 Routing Guides
1 Strain-relief Bracket
2 Blank Panels
4 Panel Clips
Install bottom front
stacker. Slide
into keyhole.
TPA-3943
2 3
1
4
8
7
5
6
24 inches
24 inches

STANDARD RECOMMENDED PROCEDURE 003-895 | ISSUE 1 | OCTOBER 2011 | PAGE 11 OF 11


Corning Cable Systems reserves the right to improve, enhance, and modify the features and specications of Corning Cable Systems’ products without prior notication. All
trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001 certied.
© 2011 Corning Cable Systems. All rights reserved. Published in Mexico.
7. 
TPA-3943
Remove:
Open front and rear doors.
Remove:
24 Panel Clips
12 Blank Panels
TPA-3944
Remove:
8 Routing Guides
2
14
3
TPA-3945
Install:
12 Tracks in base
Install:
10 Tracks in roof
Install
cassettes
(up to 12).
44
inches
5
6
8
9
10
7