CORNING SCRN-510 Manual

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 1
Small Cell Radio Node - SCRN-510 Hardware Installation
Guide
DOC-SCRN-510-HIG_i4
Issue 4
Related Literature | Search www.Corning.com/opcomm. Click Required Resources.
Revision History
Issue Date Summary of Changes
1 30JUL20 Initial release for SCRN-510 Small Cell Radio Node
2 30AUG20 Issue 2 removes UMTS references
3 01OCT20 Issue 3 adds FCC Statement
4 16OCT20 Issue 4 adds an additional Regulatory Statement

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 2
FCC Statement
Safety Precautions
Corning strongly recommends reviewing and adhering to the following cautions and notices before installing
and operating the SCRN-510.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void
your authority to operate this equipment.
RF Exposure warning statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum 40 cm between the radiator and your body.
This transmitter must not be collocated or operating in conjunction with any other antenna or transmitter
unless authorized to do so by the FCC.
This device can be expected to comply with part 15 of the FCC Rules provided it is assembled in exact accor-
dance with the instructions provided with this kit. Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received includ-
ing interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pur-
suant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
WARNING: This warning symbolizes danger that may cause severe injury or death. Before installing
or servicing equipment ensure that you are aware of all hazards involved with electrical circuitry and
become familiar with applicable safety standards and national and local electrical codes and any
other relevant standards.
WARNING: Do not locate outdoor antennas near overhead power lines or other power circuits that
might come into contact with the antennas and their wiring. Contacting such circuits during installa-
tion can cause severe injury or death. Refer to national and local electrical codes and any other rele-
vant standards for more safety information.
WARNING: Ensure that you install a suitable lightning arrestor for outside antenna installations.
WARNING: Do not use or service any equipment with outdoor connections during electrical storms
due to risk of lightning.
WARNING: All electrical equipment must be properly grounded. Refer to national and local electrical
codes and any other relevant standards for electrical grounding information.
WARNING: If an external antenna starts to fall during installation, for models that are designed for
external antennas, let it drop as it may contact a power line or other electrical circuitry that might
cause severe injury or death.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 3
Other Cautions
NOTE: This device does not require professional installation.
CAUTION: ESD can damage the SCRN-510 and internal components. Ensure that the SCRN-510 and
associated antenna equipment is installed and serviced according to national and local ESD stan-
dards.
CAUTION: Ensure that the antenna cable conforms to the environment in which it is used.
CAUTION: Do not open the SCRN-510 casing. E-RAN wireless system equipment must only be ser-
viced by Corning-accredited personnel. Opening the SCRN-510 casing voids the warranty.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 4
Table of Contents
FCC Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Other Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 1. About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 2. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Section 3. Radio Node Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Section 3.1 Radio Node Cover-Side and Mounting-Side Views . . . . . . . 7
Section 4. Connectors, SFP+ and Micro-USB Ports, and Status LED . . . . . . . . 8
Section 4.1 Duplex Phoenix Power Cable Ports . . . . . . . . . . . . . . . . . . . . . 8
Section 4.2 SFP+ Transceiver Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 4.3 Micro-USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 4.4 Status LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Section 5. System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Section 6. Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 7. Mounting the Radio Node . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 7.1 Flush Mounting the SCRN-510 . . . . . . . . . . . . . . . . . . . . . . . . . .11
Section 7.2 Downtilt Mounting the SCRN-510. . . . . . . . . . . . . . . . . . . . . . 12
Section 8. Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section 9. Completing the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section 10. Detaching the Radio Node from the Mounting Brackets . . . . . 14
Section 11. Radio Node LED Boot Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Section 12. Radio Node LED Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Section 12.1 Disabling the LED display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Section 12.2 Re-Enabling the LED Display. . . . . . . . . . . . . . . . . . . . . . . . . . 16
Section 13. Corning Documentation Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 5
1. About this Manual
The Corning SCRN-510 small cell radio node is an integrated 5G new radio (NR) mmWave radio node that is
part of the Corning enterprise radio access network (E-RAN). The scalable SCRN-510 radio node and the enter-
prise radio access network (E-RAN) simplify the complexity of radio management and mobility, and provide
operators with a single interface to aggregate and manage a large network of radio nodes. This guide pro-
vides the system specifications of the SCRN-510. It includes detailed hardware installation instructions, the
boot sequence, and expected LED behavior both during the boot-up and under normal operating conditions.
NOTE: The 5G New Radio (NR) is a new radio access technology developed by 3GPP for fifth generation (5G)
mobile networks.
The primary audience for this guide includes network planners, system administrators and installation per-
sonnel. It assumes you have knowledge about networking principles, networking configuration, site prepara-
tion, powering, and experience in hardware installation and maintenance.
2. Product Overview
The SCRN-510 is a 5G mmWave Time Division Duplexing (TDD) radio node that supports 2 x 2 MIMO small cell
operation on NR band n261, enabling high user capacity and high data rates for the coverage footprint. The
SCRN-510 connects to a Corning centralized unit (CU). It uses certificate-based authentication with the Corn-
ing CU. SCRN-510 radio nodes are managed by the Corning centralized units installed in the enterprise or in a
centralized location such as a data center.
The SCRN-510 includes built-in self-organizing networks (SON) features for ease of deployment. Its fronthaul
network can be deployed using approved 10 Gb fiber optic cables. The radio node receives 48 VDC power from
a Corning PSU6 DC Power Supply Unit or equivalent. There is no management or console port on the radio
node, and the radio node is physically locked to prevent theft. The SCRN-510 is fan-cooled, and its antennas
are built-in. Each SCRN-510 comes with a ceiling-mount bracket attached for installing directly to a flat sur-
face, as well as a second multi-angle (0, 15, 30, and 45 degree) wall-mount bracket loose in the box.
The SCRN-510 uses on-chip Trusted Platform Module (TPM) functions to implement secure boot, and to estab-
lish certificate-based IPsec tunnels to the centralized unit. It includes a PTP client to achieve frequency and
phase synchronization with other mmWave radio nodes and base stations. When used with 2 x 100 MHz
channel bandwidth on the downlink, a radio node supports a peak downlink rate of 1.1 Gbps and a peak uplink
rate of 60 Mbps @ 64QAM.
The E-RAN element management system includes configuration, fault and performance monitoring, and
security functions.
Figure 1 shows the logical architecture of the SCRN-510 in an E-RAN network.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 6
Figure 1 5G NR and E-RAN Radio Node Relationship to Enterprise and Mobile Operator Core Networks
3. Radio Node Model
Table 1 includes the SCRN-510 radio node configuration.
Table 1 SCRN-510 Radio Node Configuration
Radio Node Model Description Antenna Type
SCRN-510-28G1 28 GHz band n261 mmWave RN with 8 x 8 dual-polarization antenna array Internal
Email Web
DMZ
Enterprise
Mobile
Operator
Core
SCRN-510
Radio
Nodes
5G RN
Fronthaul
Core
Switch
Firewall
Security
Gateway
5G
EN-DC
UEs
PSU6
5G Centralized
Unit (CU)
NR
(5G)
DC
Power
10G
Connections
4G RN
Fronthaul
PoE+
Switch
4G Services
Node (SCSN)
4G and 5G EN-DC RAN
LTE
(4G)
CU IPsec
Backhaul
S1-U
3GPP
GTP Tunnel
4G
Radio
Nodes
1G
Connections
SCSN IPsec
Backhaul
3GPP
Tunnel
X2
4G
UEs

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 7
3.1 Radio Node Cover-Side and Mounting-Side Views
Figure 2 and Figure 3 display cover and mounting-side views of the radio node.
Figure 2 Radio Node Cover-Side View
Figure 3 Radio Node Mounting-Side View With Ceiling-Mount Bracket

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 8
4. Connectors, SFP+ and Micro-USB Ports, and Status LED
The radio node has the following connectors and a small form-factor pluggable SFP+ port, as shown in
Figure 4.
4.1 Duplex Phoenix Power Cable Ports
The SCRN-510 has two 48 VDC power connectors for delivering power from a Corning PSU6 DC Power Supply
Unit or equivalent to the radio node. Plug the Phoenix power connectors from the power source cable into the
power connectors; one connector into the PRIMARY port, and then another connector into the SECONDARY
port. Both ports must be provided with power.
4.2 SFP+ Transceiver Port
The enhanced small form-factor pluggable (SFP+) is a compact, hot-pluggable network interface module. The
approved SFP+ included on the Bill Of Materials supports 10 GbE (Gigabit Ethernet). Connect the fiber pair of
the ActiFi cable (or other approved fiber cable) with approved SFP module termination to the SFP port for con-
necting the radio node to the fronthaul transport network.
4.3 Micro-USB Port
The Micro-USB port is used for advanced configuration. For use only by authorized technicians.
4.4 Status LED
The STA (status) RGB tri-color LED indicates the state of the SCRN-510, with boot, normal, disabled, fault, and
radio node indications. When the radio node initially boots, the LED cycles through a number of colors and
flashing behaviors until the SCRN-510 is fully operational. Section 11., Radio Node LED Boot Sequence
describes the STA LED indications.
Figure 4 SCRN-510 Connectors and Status LED

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 9
5. System Specifications
The SCRN-510 radio node has the chassis measurements, power requirements, and environmental require-
ments, and complies with the standards listed in Table 2. Refer to the feature guide for your centralized unit
software release for release-specific features and specifications.
Table 2 SCRN-510 Radio Node Specifications
Operating Band 2 x 2 MIMO operation on 28-GHz NR band n261 (27.5–28.35 GHz)
Channel Size Component Carrier (CC) bandwidth: 100 MHz
Antenna Type 8 x 8 dual-polarization internal antenna array
Antenna Power 43 dBm EIRP @ 64QAM
Beamforming scan range: +/- 60 degrees
RF Management Beam Management with auto-assignment of physical cell identities (PCIs)
QoS Features Non-GBR bearer support per UE
Dimensions 31.75 x 31.75 x 11.43 mm (12.5 x 12.5 x 4.5 in)
Weight 5.31 kg (11.72 lbs)
Input Power 2 x 48 VDC Phoenix
Power Consumption 100 W
Ingress Protection Ingress protection rating: IP30
Performance Hardware capable of 4CC; up to 32 active users
Peak Tx Rate 1.1 Gbps DL, 60 Mbps UL (DL:UL slot ratio of 4:1) @ 64QAM with 2CC DL, 1CC UL
Licensed Tx Power Equivalent isotropically radiated power (EIRP): 43 dBm
Ethernet Interface SFP+ supports 10 GbE (Gigabit Ethernet)
LEDs 1 tricolor (RGB) LED to indicate power and status
Synchronization IEEE 1588v2-based (PTP) synchronization with an external PTP grandmaster clock
Mounting Wall or Ceiling, brackets included
Brackets support four tilting options: 0°, 15°, 30° and 45° tilt
Cooling Method Active cooling (Noise level: 30 dBA)
Security
Secure boot and secure key storage using Trusted Platform Module (TPM) functions
IPsec tunneling to NR CU (Centralized Unit)
X.509 certificate-based authentication
Environmental
Requirements
Operating temperature range: 0o to 45oC (32o to 113oF)
Non-operating temperature range: -40o to +70oC (-40o to 158oF)
Relative humidity: Operating and storage: 0% RH to 90% RH non-condensing
MTBF 1,363,791 hours at +40°C (104°F)

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 10
6. Compliance
The SCRN-510 complies with the standards listed in Table 3.
7. Mounting the Radio Node
Radio Nodes can be installed on walls and below ceilings with the factory-provided brackets. When mounting
a radio node vertically on a wall, position the fans on the upper side of the SCRN-510. The factory-provided
wall-mount bracket can tilt the SCRN-510 down at the following angles: 0°, 15°, 30° and 45°. Figure 5 shows the
SCRN-510 tilt options.
Figure 5 Mounting Bracket Downtilt Options
NOTE: Always consult and follow local codes for mounting and wiring Corning equipment.
When possible, locate downward-radiating radio node units at least 0.5 meters (20 inches) from external
walls. This distance maximizes indoor coverage and minimizes RF leakage outside the building. When mount-
ing near a wall or other obstruction, orient the mounting bracket so that the top of the SCRN-510 faces
towards the coverage area and faces away from the wall.
Table 3 SCRN-510 Compliance
Safety TUV Safety (Including UL-62368-1 2nd
Edition)
FCC Compliant - Part 15 (Class A), Part 30
MPE: FCC 47 CFR 1.1310
UR: FCC 47 CFR 1.1307(b)
0° 15° 30° 45°

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 11
7.1 Flush Mounting the SCRN-510
As shown in Figure 3, the SCRN-510 comes with the ceiling-mount bracket attached. This bracket is held to the
radio node mounting side with four shoulder screws and a captive securing screw, and is non-tilting. The
shoulder screws should not need to be adjusted but if they do, loosen them slightly to be able to slide the ceil-
ing-mount bracket on and off of the radio node when the captive securing screw has been loosened. Figure 6
shows the captive securing screw and four security screw locations.
NOTE: The security screws should not need to be adjusted but if they do, loosen them slightly to be able to slide
the ceiling-mount bracket on and off.
Figure 6 Ceiling-Mount Bracket Screw Locations
Step 1 Loosen the captive securing screw on the ceiling-mount bracket.
Step 2 Slide the ceiling-mount bracket toward the captive securing screw to remove it from the SCRN-
510 base.
NOTE: The shoulder screws should not need to be adjusted but if they do, loosen them slightly to be able to
slide the ceiling-mount bracket on and off.
Step 3 Secure the ceiling tethering system. Make sure that it can support the weight of the SCRN-510
and the ceiling-mount bracket.
NOTE: Corning recommends that you use a customer-supplied projector mount when hanging the SCRN-510
from a dropped T-bar ceiling.
Step 4 Secure the ceiling-mount bracket to ceiling tethering system.
Step 5 Slide the radio node back onto the bracket and gently tighten the securing screw.
Figure 7 shows a typical SCRN-510 mounted to a ceiling tethering system.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 12
Figure 7 Ceiling-Mounted SCRN-510
7.2 Downtilt Mounting the SCRN-510
The SCRN-510 comes with the ceiling-mount bracket attached, and has the multi-angle wall-mount bracket
loose in the box. Figure 8 shows the SCRN-510 wall-mount bracket.
Figure 8 SCRN-510 Wall-Mount Bracket
When using the multi-angle wall-mount bracket, it is not necessary to remove the ceiling-mount bracket
from the SCRN-510; the wall-mount bracket attaches to the wall, and then it attaches to the ceiling-mount
bracket-and-radio node assembly. Figure 9 shows how the wall-mount bracket attaches to the ceiling-mount
bracket.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 13
Figure 9 Wall-Mount Bracket Attached to the Ceiling-Mount Bracket
Step 1 Using a spirit level, use the wall-mount bracket as a template to mark securing hole locations.
Step 2 If required, install sheet rock plugs.
Step 3 Attach the wall-mount bracket to the wall. Figure 10 shows the SCRN-510 wall-mount bracket
attached to a wall.
Figure 10 Wall-Mount Bracket Attached to a Wall
NOTE: Production wall-mount brackets will have a large hole in the back for routing cables.
Step 4 Seat the ceiling-mount bracket on wall-mount bracket:
- First, slide the ceiling-mount bracket onto the wall-mount bracket hinge pins.
- Then, set the SCRN-510 to the required tilt, and tighten the wall-mount bracket
captive securing screw to lock the radio node tilt angle.
NOTE: Put pressure on the SCRN-510 when tightening the captive securing screw.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 14
Figure 11 shows how to attach the wall-mount bracket to the ceiling-mount bracket.
Figure 11 Attaching the Wall-Mount Bracket to the Ceiling-Mount Bracket
Step 5 Make sure that both of the captive securing screws are tightened.
8. Cabling Guidelines
Incorrectly cabling a SCRN-510 can result in crushed cables and loss of communications to the radio node. Fol-
low these guidelines when cabling the radio node:
• Make sure that the cabling is properly routed and dressed.
• When mounting the radio node vertically, orient the bracket so that the bracket keyholes have the
wide side up as shown in Figure 3.
• Make sure that the radio node is fully secured to the mounting brackets so that it locks into place.
A correctly-installed cable should at no time during installation impede inserting the radio node
into the mounting brackets.
9. Completing the Installation
Step 1 Make sure that the captive securing screws are tightened. The radio node is now anchored.
Step 2 When it receives power, the radio node boots up and attempts to connect to the centralized
unit.
10. Detaching the Radio Node from the Mounting Brackets
Step 1 Loosen the captive securing screws anchoring the radio node to its mounting brackets.
Step 2 Slide the radio node out of the mounting brackets.
Step 3 Detach the cables from the cable brackets and cable openings.
11. Radio Node LED Boot Sequence
The radio node state machine is sequential and progresses in the following order:
State 0 -> State 1 -> State 2 -> State 3 -> State 4 -> State 5 -> State 6
A normal boot sequence transitions through all these states sequentially and the LED state transitions
accordingly. If the radio node fails to transition to the next state, the system restarts the boot sequence, start-
ing with State 0. You can determine the progress during the booting stages by observing the LED color transi-
12

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 15
tions. On failure, the last LED state will display the state that encountered the failure. Table 4 shows the radio
node boot sequence and corresponding LED behavior.
Table 4 Radio Node LED Boot Sequence
State
LED
Color Description Possible Failures and Actions
0. Power On/
Reset
Flashing
White
This is the initial state on startup. The radio
node bootup is controlled by firmware in this
state.
This state should be very short lived
and should transition to the next state
immediately.
1. Software
Initialization
Flashing
Green
The firmware has loaded and transferred
control to the bootloader. Additional
hardware initialization and validation are
performed during this state. This state
concludes with a lamp test, cycling through
all LED colors.
This state should be very short lived
and should transition to the next state
immediately.
A radio node should not stay in this
state indefinitely.
Note: Flashing Green is also used to
indicate a radio node that has been
administratively disabled. This can be
determined from the CLI.
2. DHCP Solid Red The radio node starts by sending out a DHCP
Request.
The radio node moves to the next state
(State 3) upon receiving a DHCP response
and an IP Address.
No DHCP Response, IP Address not
allocated.
Check cabling, DHCP Server
configuration.
3. Join Solid
Blue
The radio node has an IP Address and sends a
UDP Join request to the Serving centralized
unit.
The radio node moves to the next state
(State 4) upon getting a JOIN GRANT from
the centralized unit.
No IP reachability to the centralized
unit.
Check IP network between radio node
and centralized unit for routing issues.
4. TFTP Flashing
Blue
The radio node proceeds next to download
the operating system image from the
centralized unit.
The radio node moves to the next state
(State 5) after the image has been
downloaded.
Failure to download TFTP image.
Check firewall between radio node and
centralized unit.
5. Operating
System Booting
Flashing
Green
The radio node loads the operating system
and starts the default platform applications.
The radio node moves to the next state
(State 6) when it establishes connectivity
with the centralized unit.
Failure to start the operating system.
This normally points to a software/
build issue. Please contact Corning
support.
6. Running Solid
Green
The operating system is running. The radio
node continues the startup sequence, but is
now controlled by the centralized unit.
The operating system is up and running
on the radio node.
Any subsequent state transitions can
now be tracked from events and logs
on the centralized unit.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 16
12. Radio Node LED Management
The LED display is active by default, but can be deactivated in light-sensitive environments as needed. Even
when the display is disabled, the LED will be lighted during the following conditions:
• while the radio node is booting
• if the radio node or cell is in fault state
• if there is an active emergency call
• if the locate radio node feature is active
Table 5 shows the default LED behavior of the radio node:
12.1 Disabling the LED display
Step 1 From the CLI Configuration Mode, issue the set System RadioNode LED DefaultMode Dark
command to disable the LED display:
%set System RadioNode LED DefaultMode Dark
Step 2 Issue the show System RadioNode LED command to verify the configuration:
%show System RadioNode LED
DefaultMode Dark;
12.2 Re-Enabling the LED Display
Step 1 From the Configuration Mode, issue the set System RadioNode LED DefaultMode Standard
command to re-enable the LED display:
%set System RadioNode LED DefaultMode Standard
Step 2 Issue the show System RadioNode LED command to verify the configuration:
%show System RadioNode LED
DefaultMode Standard;
Table 5 Radio Node LED Behavior
LED Status Flash Rate
White: slow flashing Software initialization Approximately ½ second on, 1½ sec. off
Green: slow flashing The radio node or radio is administratively
disabled
Approximately ½ second on, 1½ sec. off
Green: fast flashing Booting Approximately 1.4 second on/off cycle
Green: solid Operational
Red: solid Fault
Blue: fast flashing Locate radio node enabled (Note) Approximately 1 second on/off cycle
Blue: solid Follow IMSI enabled
Off Powered off or LED disabled
Note: Refer to the Corning OS (SCOS) Administrator Guide for information about the locate radio node and follow
IMSI features.

Corning Restricted and Confidential Proprietary - Controlled content
SCRN-510 Hardware Installation Guide | DOC-SCRN-510-HIG_i4 | 16 October, 2020 | Page 17
13. Corning Documentation Set
The Corning documentation can be downloaded from the customer support portal (the “Corning One Com-
munity”) at https://onesupport.corning.com. This site requires a login which is available to individuals who
have attended Corning Small Cell training in the past two years. Email [e-mail] to request a
login if you meet these criteria.
Corning Optical Communications LLC • 4200 Corning Place, Charlotte, NC 28216 USA
800-743-2675 • FAX: [phone] • International: [phone] • www.corning.com/opcomm
Corning Optical Communications reserves the right to improve, enhance, and modify the features and specifications of Corning Optical Communications products without prior
notification. A complete listing of the trademarks of Corning Optical Communications is available at www.corning.com/opcomm/trademarks. All other trademarks are the proper-
ties of their respective owners.
Corning Optical Communications is ISO 9001 certified. © 2020 Corning Optical Communications. All rights reserved.