Courtyard Creations Easton User manual

SGS210B
Do not discard any of the packaging until you have checked that you have all the parts and
pack of fittings.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Keep children away during assembly. This item contains small parts which can be
swallowed by children. Children should always be under direct adult supervision while
using the product.
Retain the assembly instructions for future reference.
Please quote following FQC NO. when contacting service center.
SERVICE CENTER TOLL FREE NO
TEL: [phone]
FAX: [phone]
PAGE 1 OF 2
PARTS LIST
1
1
4
8
8
1
1
TGS50SC-CS01
TGS50SC-CS02
62TGS52SGY101
17FA05040301-Y4
18000337002
XGZ0070
17KAA0201----Y4
TABLE TOP
LEG
CENTER
CONNECTOR WITH RING
HEX.KEY WRENCH 6MM
LAZY SUSAN
BOLT CAP M6
WASHER d6.5*D13*1.0
FIGURE 1
4
1
COURTYARD CREATIONS INC.
PART
NO. MATERIAL CODE PART Q’TY
1
2
3
4
6
7
8
9
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
!
!
!
!
!
!
SCREW ST4.2*12 4
17C17A0403001Y4
58
17C01A0706002Y4
BOLT M6*16
Step 1:
Place the table top (#1) onto a non-abrasive
surface, such as a carpet, with the underside facing
up. Insert the legs (#2) into the plastic holders
attached on the underside of the table top (#1) rim.
Fasten them together by using screws (#4).
See Figure 1.
You will need the following tools:
-Phillips Screwdriver (Not included)
-Hex.Key Wrench (See Part #9)
Easton 50 in. Round Marble Painted Glass
Dining Table with 18 in. Lazy Susan

FIGURE 2
2
5
6
7
5
6
7
FIGURE 3
FULLASSEMBLY
8
Step 4:
See Full Assembly.
Step 3:
Turn the table to its upright position and place
the lazy susan (#8) onto the table top.
See Figure 3.
Note:
To use an umbrella with this table, please remove
the plastic center plug and put the umbrella pole
through the table top and center connector ring.
Cleaning and Maintenance
•Wash frame parts with mild soap and water, rinse thoroughly, and dry frame completely. Do not use
bleach, acid, or other solvents on the frame parts.
•Wash glass with mild soa
p and water, rinse thoroughly and dry glass completely.
•Please inspect and tighten all bolts and fasteners on a regular basis to ens
ure proper performance and
safety of your table.
• When moving the table, remove the umbrella. Do not drag.
•We recommend the use of furniture covers when not in use.
•In order to prolong the life and beauty of your table, we recommend it be stored in a dry an
d protected
area during off season periods.
• Tempered glass has been used for increased strength and
safety of your table. However, during windy
conditions the umbrella should be lowered and/or removed.
PAGE 2 OF 2
Missing A Part?
No Need To Go Back To
TheStore!
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
Call Toll Free
TEL: [phone]
FAX: [phone]
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
PLEASE READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
PLEASE SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
SHOULD YOU NOTLOCATE ALL OF THE ABOVE PARTS, PLEASE INSPECTALL
PACKING MATERIAL FOR ANYSMALL PARTSTHAT MAYHAVEBECOME
SEPARATED IN SHIPMENT.
SHOULDYOU EXPERIENCEANYDIFFICULTYDURING ASSEMBLYOR IF ANY
PARTIS MISSING OR DAMAGED,PLEASE CALL THE HELP LINE 1-877-539-7436
BEFORERETURNING THEITEM TO THESTORE.
PLEASE PROVIDE THEFOLLOWING INFORMATION:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS LIST
SHOWN ON ASSEMBLY INSTRUCTIONS.
MOST PROBLEMSCAN BERESOLVED WITHOUT RETURNING THIS PRODUCT
TO THERETAILER.
The store where you made your purchase
does not stock parts for this item
if you need parts,
whether they are missing or damaged.
STOP!
MissingAPart?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free
TEL: [phone]
FAX: [phone]
Step 2:
Fasten the center connector with ring (#3) to the
legs (#2) by using bolts (#5) and washers (#6).
Make sure that all of the bolts have been tightened
completely, and then cover them with bolt caps
(#7). See Figure 2.