Courtyard Creations TGS39SW-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PARTS LIST
TGS39SW-WM
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
7
8
2
3
4
5
6
PAGE 1 OF 2 COURTYARD CREATIONS INC.
!
!
!
!
!
!
!
1
4
1
4
4
4
4
1
FIGURE 1
LEG
SCREW ST4.2*12
CENTER
CONNECTOR WITH RING
BOLT M6*25
WASHER d6.5*D13*1.0
BOLT CAP
HEX.KEY WRENCH 4MM
17FA05040301-Y4
17C33A0709001Y4
18000337004
17KAA0101----Y4
TGS39SW-CS01
TGS64SW-CS02
62TGS39SWY101
17C17A0403001Y4
TABLE TOP
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Hex. Key Wrench (See Part #8)
2
22
2
1
4
Step 1:
Place the table top (#1) onto a non-abrasive
surface, such as a carpet, with its underside
facing upwards. Insert the legs (#2) into the
plastic holders on the underside of the table
top (#1) rim. Fasten them together by using
screws (#4). See Figure 1.
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not sit or stand on this table.
A weighted umbrella base must be used when using an umbrella with this table.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
STOP DON’T RETURN TO STORE!

FIGURE 3
PAGE 2 OF 2
FIGURE 2
Step 2:
Fasten the center connector with ring (#3) to the
middle of the legs (#2) by using bolts (#5) and
washers (#6). Make sure that all of the bolts have
been tightened completely and cover them with
bolt caps (#7). See Figure 2.
Step 3:
Turn the table to its upright position. See Figure 3.
2
22
2
3
7
5
6
Note:
The arrow marks on the center connector with
ring (#3) should coincide with Figure 2 to ensure
proper assembly.
Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame parts.
• Wash glass with mild soap and water, rinse thoroughly, and dry completely.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and
safety of your table.
• When moving the table, remove the umbrella and lift. Do not drag this table.
• We recommend the use of furniture covers when not in use.
• In order to prolong the life and beauty of your table, we recommend that it be stored in a dry and
protected area during off season periods.
• Tempered glass has been used for increased strength and safety of your table. However, during windy
conditions the umbrella should be lowered and/or removed.
Note:
To use an umbrella with this table, remove the plastic
center plug and put the umbrella pole through the
table top and center connector ring.
STOP DON’T RETURN TO STORE!
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.