Courtyard Creations KSS100X-WM User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
KSS100X-WM
PARTS LIST
PART
NO. MATERIAL CODE PART Q’TY PART NO. MATERIAL CODE PART Q’TY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
8
2
8
1
1
1
1
2
1
1
2
2
2
2
2
1
2
4
2
8
8
4
16
4
KSS1008-CS01
KSS1008-CS02
KSS1008-CS03
KSS1008-CS04
KSS1008-CS05
KSS1008-CS06
KSS1008-CS07
KSS1008-CS08
17C01A0844061Y4
17C01A0756131Y4
17C01A0716072Y4
17C17A1904001Y4
17FA05040301-Y4
17FA08060601-Y4
18000C23001
17D03A040401-Y4
18000337002
17KAB1101----Y4
17KAA0201----Y4
61K100XC00001BA
61K100XC50001BA
61K100XJ00001BA
61K100XG00008IA
61K100XQ00008IA
SEAT BASE
SEAT BASE
MIDDLE SEAT
BACK A
BACK B
MIDDLE LEG
LEG
SEAT CROSS BRACE
BOLT M8*95
BOLT M6*48
BOLT M6*45
SCREW ST3.9*13
WASHER d6.5*D13*1.0
WASHER d8.5*D17*1.6
PLASTIC NUT M6*P1.0
JAM NUT M8*1.25
BOLT CAP M6
NUT WRENCH 10 & 13MM
HEX.KEY WRENCH 6MM
LEFT CUSHION
RIGHT CUSHION
PILLOW
COVER BAG
COVER
Use the correct bolts as indicated. Do not tighten any of the bolts until is completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
COURTYARD CREATIONS INC.
!
!
!
!
!
PAGE 1 OF 4
STOP DON’T RETURN TO STORE!

PAGE 2 OF 4
95
#9 BOLT M8*95
Step 1
Step 2
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
You will need the following tools:
- Phillips Screwdriver (Not Included)
- Nut Wrench (See Part #18)
- Hex.Key Wrench (See Part #19)
Attention:
Make sure that each bolt needed for
all steps matches the corresponding
figure to ensure proper assembly.
Step 1:
Fasten the middle leg (#6) in the
center of the middle seats (#3) by
using bolts (#9), washers (#14), and
jam nuts (#16). Do not fully tighten
the bolts yet. See Figure 1.
Note:
The labelled arrow marks on the
middle seats should be facing
upwards to ensure proper assembly.
Step 2:
Insert the seat bases (#2) into the
middle seats (#3). Please ensure that
their holes align. Do the same
procedure for both sides.
See Figure 2.
Note:
The labelled arrow marks on the seat
bases (#2) should match those on the
middle seats (#3) to ensure proper
assembly.
Step 3:
Insert the seat bases (#2) into the seat
bases (#1). Make sure the spring clips
on the seat bases (#2) come through
the holes on the seat bases (#1).
See Figure 3.
Note:
The labelled arrow marks on the seat
bases (#1 and #2) should be facing
upwards to ensure proper assembly.
Step 4:
Insert the connector tabs on the seat
bases (#1) into the legs (#7). Make
sure the spring clips on the seat bases
(#1) come through the boles on the
legs (#7). See Figure 4 - Step 1.
Fasten the middle seats (#3) to the
seat bases (#2) by using screws (#12).
See Figure 4 - Step 2.
STOP DON’T RETURN TO STORE!

PAGE 3 OF 4
48
#10 BOLT M6*48
45
#11 BOLT M6*45
FIGURE 5
FIGURE 6
FIGURE 7
Step 5:
Fasten the back A (#4) to the middle seat
(#3) by using bolts (#10). See Figure 5.
Note:
The label mark “A” on back A (#4) should be
facing upwards to ensure proper assembly.
Step 6:
Fasten the seat cross brace (#8) to the back
A (#4) and the seat base (#1) by using bolts
(#11), washers (#13) and plastic nuts (#15).
Repeat Figure 5 and Figure 6 for the
remaining back A (#4) and backs B (#5).
See Figure 6 and Figure 7.
Make sure that all of the bolts have been
tightened completely and cover them with bolt
caps (#17).
Note:
The labelled marks “A and B” on backs A (#4)
and backs B (#5) should be facing upwards
to ensure proper assembly.
STOP DON’T RETURN TO STORE!

PAGE 4 OF 4
FIGURE 8
FIGURE 9
Step 7:
Place the cushions (#20 and #21) and the
pillows (#22) onto the lounge. Secure the cover
bag (#23) onto the seat base (#1) by using the
velcro straps. See Figure 8.
Note :
To prevent your lounge from the rust, you can
use the cover (#24) provided in the cover bag
(#23).
Note :
To turn the lounge into a bed, pressing the
spring buttons on the seat cross braces (#8).
The seat cross braces have two pre-drilled
holes that allow the backs to recline into two
positions. See Figure 9.
Attention:
Orbit lounge dust cover is intended for dust
only. Not water resistant!
Special Warnings:
• Inspect this lounge before each use.
•Position the lounge on level ground and no
less than six feet away from any obstruction
such as, fences, garages, houses, overhanging
branches, laundry lines, electrical wires, etc.
• Ensure the tightness of all nuts and bolts on
a regular basis.
• The manufacturer will not accept responsibility
for unauthorized repairs and/or modifications
made to the lounge.
• Weight limit is 220 kgs.
Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
• Cushions may be washed on the surface only by using mild soap and water or commercial foaming upholstery
cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of
your lounge.
• In order to prolong the life and beauty of your lounge, we recommend that it be stored in a dry and protected
area during off season periods.
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL PARTS, MAKING SURE THAT YOU
HAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
STOP DON’T RETURN TO STORE!