COZY VC201A and User manual

Gas-Fired Vented
Room Heater
INSTALLATIONAND
OPERATINGINSTRUCTIONS
P/N 80900 - REV. 12/03
Thisapplianceisequippedwith asafetycontrolsystemdesignedtoprotectagainst
improperventingofcombustionproducts.
THIS UNIT IS NOT TO BE INSTALLED IN MOBILE HOMES.
WARNING: If theinformation inthis manualis not
followed exactly, a fire or explosion may result
causingproperty damage,personal injuryorloss of
life.
-Donotstoreoruse gasoline or other flammable vapors
andliquids inthevicinityof thisoranyotherappliance.
- WHAT TODOIF YOUSMELLGAS:
•Donottryto light any appliance.
•Donottouchanyelectricalswitch;do not use any phone
inyourbuilding.
•Immediatelycallyourgassupplierfromaneighbor’s
phone. Followthegas supplier’s instructions.
•Ifyoucannotreachyour gas supplier,callthefire
department.
-INSTALLATION ANDSERVICEMUST BE
PERFORMEDBYAQUALIFIEDINSTALLER,
SERVICE AGENCY ORTHE GAS SUPPLIER.
WARNING: Operationofthis heaterwhen notconnectedto aproperlyinstalledandmaintained
ventingsystem ortampering withthe ventsafety shut-offsystem canresultin CarbonMonoxide
(CO)poisoningand possibledeath.
RADIANTFRONT
CLOSED FRONT
This unit is not approved for installation in mobile homes, greenhouses, or environments involving
dusty, wet, corrosive, or explosive conditions. Such conditions will invalidate the warranty and may
create unsafe conditions.
Thecoatingselectedtoprovidelongerlife
tothe heat exchangermaysmoke slightly
uponinitialfiring. Provideadequateventi-
lationifthisoccurs.
NATURAL GAS VC201A VC351A VC501A VC701A VCR351A VCR501A VCR701A
PROPANE GAS VC202A VC352A VC502A VC702A VCR352A VCR502A VCR702A
R
R

SPECIFICATIONS………………………. 2
INTRODUCTION……………………….. 3
VENTING………………………………... 3 ,4
GASSUPPLY……………………………. 5
LOCATION&SPECIALPRECAUTIONS 5
COMBUSTION&VENTILATIONAIR.... 6
CLEARANCES………………………….. 7
DRAFTDIVERTER…………………….. 7
DOORKNOB…………………………… 7
PILOTADJUSTMENT…………………. 8
RADIANTS&GLASSPANELS……….. 8
BURNERORIFICE&ORIFICECHART.......... 8
PROPERBURNERFLAME.............…………. 9
MAINTENANCE…………………………....... 9
LIGHTINGINSTRUCTIONS……………........ 10
TROUBLESHOOTINGCHART………… 11,12
BLOWERINSTRUCTIONS……………… 13
PARTSDRAWING……………………….. 14
PARTSPRICELIST………………………. 15
WARRANTY……………………………… 17
READCAREFULLY BEFOREINSTALLINGUNIT
These installation instructions are a general guide and do not supersede applicable local codes and ordinances. Before
planning or making the installation be sure it complies with all phases of the local heating code. (Or, in the absence of
local codes, with the latest edition of National Fuel Gas Code, ANSI.Z223.1, or CAN1-B149).
The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local
codes, with the latest edition of National Electrical Code ANSI/NFPA 70, or Canadian Electrical Code CSA-C22.1.
All of the ANSI and NFPA standards referred to in these installation instructions are the ones that were applicable at
thetime the designof this appliancewas certified. The ANSIstandards are availablefrom the AmericanGas Association,
1515 Wilson Blvd., Arlington, VA. 22209.
The NFPA standards are available from the national Fire Protection Association, 60 Batterymarch Street, Boston,
Massachusetts 02110.
Canadian standards are available from International Approval Services, 178 Rexdale Boulevard, Etobicoke, Ontario,
Canada M9W 1R3.
The design of this appliance was certified to comply with ANSI Z21.11.1 vented room heaters and CAN1-2.1-M86.
Installer must leave these instructions with the consumer, have them complete, and return the warranty card.
ROOMHEATERSPECIFICATIONS
Your room heater comes packed in a single carton. Before installation, check the rating plate to verify that the Model Number is
correct and that the room heater is equipped for the type gas you intend to use.
TABLEOF CONTENTS
TYPE CONTROL GAS MODEL NUMBERS
CLOSEDFRONT THERMOSTAT BULB NATURAL VC201A VC351A VC501A VC701A
CLOSEDFRONT THERMOSTATBULB L.P. VC202A VC352A VC502A VC702A
RADIANTFRONT THERMOSTATBULB NATURAL N/A VCR351A VCR501A VCR701A
RADIANTFRONT THERMOSTATBULB L.P. N/A VCR352A VCR502A VCR702A
HEIGHT 20” 26” 26” 30”
WIDTH 24” 30” 30” 36”
DEPTH 15-1/4” 15-1/4” 19-1/4” 19-1/4”
INPUT(BTU/HR.) 20,000 35,000 50,000 70,000
GASINLET/OUTLETSIZE 1/2X3/8” 1/2X3/8” 1/2X3/8” 1/2X3/8”
VENTSIZE 3” 4” 4” 5”
CENTEROFVENTTOFLOOR 16-1/2” 21-1/2” 21-1/2” 25-1/2”
NUMBEROFRADIANTS(“VCR”SERIES) N/A 5 5 5
NUMBEROFRADIANTGLASS(“VCR”SERIES) N/A 2 2 2
APPROX.SHIPPINGWEIGHT(“VC”SERIES) 55 LBS. 84 LBS. 112 LBS. 138LBS.
APPROX.SHIPPINGWEIGHT(“VCR”SERIES) N/A 96 LBS. 124 LBS. 150LBS.
*OPTIONALBLOWERMODEL N/A CHB-3 CHB-3 CHB-3
*Blowers also available factory mounted on 50M Btu units. All 70M Btu units come with blower mounted only.
SPECIFICATIONS
Page 2

INTRODUCTION
THISIS AGAS-FIRED,GRAVITYVENTEDROOM HEATERTHATWILL OPERATESAFELYAND PROVIDEANEFFICIENT
SOURCEOFHEAT WHENINSTALLED,OPERATED AND MAINTAINEDASRECOMMENDEDINTHESE INSTALLATION
ANDOPERATINGINSTRUCTIONS. READ THESEINSTRCTIONSTHOROUGHLY BEFOREINSTALLING,SERVICING,OR
USING THIS APPLIANCE. IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS, CONSULT LOCAL
AUTHORITIES,OTHERQUALIFIEDINSTALLERS,SERVICEAGENCIES,THEGASSUPPLIER,ORTHEMANUFACTURER.
VENTING
This heater must be connected to a properly installed and maintained venting system. This heater is equipped with a vent safety
shut-off device. Pilot outage will occur if the heater is not connected to a vent system. Pilot outage may occur due to restriction or
blockage in the vent or if connected to a masonry chimney having an area greater than the vent size shown on Page 2.
This appliance should be vented through a properly sized listed type B vent that has been constructed in accordance with the
National Building Code. If a horizontal section of vent is used, it must slope upwards a minimum of ¼ inch per foot of length.
This heater must not be connected to a vent system being used for wood or coal burning appliances. The use of more than one
appliance per vent system will most likely cause the vent safety shut-off device to shut off the heater due to the cooling of vent
temperatures through the draft diverter of the second appliance. In some situations, the vent safety shut-off may shut down the
heater if a too large, unlined, masonry chimney is used. Due to low vent temperatures associated with more efficient heaters it may
take too long to get the vent action going in a chimney before the shut-off device will shut down the heater. If this is the case, we
recommend lining the chimney with the proper size type B vent pipe or type B chimney liner.
WARNING: Do not bypass the vent safety shutoff switch. To do so could expose the consumer to
property damage, personal injury or possible death.
The switch, when activated, will extinguish the pilot flame. If the homeowner experiences this problem, the vent system must be
checked and corrected. NOTE: An existing vent that has worked for years may not be adequate for todays design because of
higher efficiency requirements resulting in lower stack temperatures. The following is a list of possible causes and corrective
actions.
POSSIBLECAUSES CORRECTIVE ACTION
1. Blockage in vent pipe 1.A) Check vent pipe for blockage, such as bird nest, wasp nest, twigs, leaves, etc.
1.B) Check that the vent cap is properly installed, not shoved too far down on the vent
pipe.
2. Burner is over firin 2.A) Check the manifold pressure.
2.B) Check the rate, NOTE: This appliance was orificed for elevations up to 2,000 feet.
When installed at higher elevations refer to orifice chart in main burner orifice
section of instructions for proper orifice size and re-orifice accordingly.
3. Improper vent system 3. Correct vent system.
A) Vent too short A) The vent should not terminate less than 5 feet above the drafthood connection. A
gas vent extending through an exterior wall shall not terminate adjacent to the
wall or below eaves or parapets. Also, the top of the vent must be at least 2 foot
above any obstacles within a 10 foot radius, including the roof. See Figure A.
B) Restriction in vent B) All type “B” vent shall extend in a generally vertical direction with offsets not
system caused by exceeding 45 degrees, except that a vent system having not more than one 60
offsets degree offset may be allowed. Any angle greater than 45 degrees from the vertical
is considered horizontal. The total horizontal run of a vent plus the horizontal vent
connector shall be not greater than 75 percent of the vertical height of the vent.
Any offsets used should be as far above the drafthood as possible to allow a
venting action to begin before any restriction is encountered.
C) Incorrect vent pipe C) Use listed “B” type vent pipe. Do not use transite or any other type of ceramic
pipe for venting. Do not use single wall pipe.
4. Loose connections on the 4. Check the connection on both the switch and the gas valve. Tighten if necessary.
Page 3
vent safety wiring harness

VENTING
10’ or Less
2’Min.
3’Min.
Ridge
Chimney
More than
10’ 10’
2’Min. 3’Min.
Ridge
Chimney
Height above any
roof surface
withon10’
horizontally
FIGUREA FIGUREA
Seal around collar
& flashings
Maintain
1”Clearance Support
Laterals
Termination of vent must be
securely guyed or braced if
it extends more than five (5)
feet above roof. See
Termination
diagram
above
Firestop Support
Assembly
VerticalVent
Elbow
Listed
Appl.
Terminate vent
at least 5 ft.
above draft hood
CONNECTINGTHEVENT INTO
AN EXISTING CHIMNEY
SAFE (See “Venting”)
NOTE: Thismay result
intheventsafetyswitch
shuttingdownthepilot
dependingonsize and
drawofchimney.
FIGURE7A
1/4
UNSAFE
FIGURE7B
RECOMMENDED
Usepropersize“B”
pipeorchimneyliner
insidechimney.
FIGURE7C
Page 4

GASSUPPLY
Thisventedroomheatermustbeconnectedtoagassupply
capableof supplying the appliances fullrated capacity.
Providea1/8inch N.P.T. pluggedtapping,accessiblefor
testgaugeconnection, immediately upstream ofthegas
supplyconnectiontothe appliance. The minimum inlet
pressure in the gas supply pipe should be 4.5” w.c. for
Natural Gas and 11.0” w.c. for Propane Gas, “for the
purposeofinputadjustment”. Themaximuminletpressure
inthe gassupply pipe shouldnever exceed 14” w.c. for
either Natural or Propane Gas. The gas supply piping
shouldbesizedinaccordancewithANSIZ223.1National
FuelGas Code. Thenormalmanifoldpressureshouldbe
3.5” w.c. for Natural Gas and 10.0” w.c. for Propane
Gas.
If the outlet pressure of the gas valve must be adjusted,
thisshouldbedonebyaqualifiedservicemanusingproper
toolsandinstruments.
Checkallconnectionswithsoapywaterfor possible gas
leaks. Neveruseamatch,candleorotherignitionsource.
Itis recommendedthatpipecompoundwhich isresistant
to the action of liquefied petroleum gases be used. Do
notuseTeflon tape or Teflonimpregnatedcompound.
The appliance and its individual shutoff valve must be
disconnected from the gas supply piping during any
pressuretestingofthatsystematthetestpressureinexcess
of½psig.
Theappliancemustbeisolatedfromthegassupplypiping
byclosing itsindividualmanualshutoffvalve duringany
pressure testing of the gas supply piping system at test
pressuresequal to or lessthan ½ psig.
LOCATIONANDSPEICALPRECAUTIONS
Dueto high temperaturesthe appliance shouldbe
locatedout of trafficand away fromfurniture and
draperies.
Childrenandadultsshouldbealertedtothehazards
ofhigh surface temperatureandshould stay away
toavoidburnsorclothingignition.
Youngchildrenshouldbecarefullysupervisedwhen
theyarein the same room astheappliance.
Clothingor otherflammablematerialshouldnotbe
placedon or near theappliance.
Any safety screen, guard, or casing top removed
forservicinga room heatermustbereplaced prior
tooperatingtheappliance.
Do not use this heater if any part has been under
water. Immediatelycallaqualifiedservicetechnician
toinspect theheater and toreplace any partof the
controlsystemandanygascontrolwhichhasbeen
underwater.
For purpose of identifying the sides of the heater.
Whenyouarefacingthefrontoftheheatertheright
sidehas the access doorand the left sideis solid.
Ifheaterisinstalledinaresidentialgarage,allburners
and pilot must be above 18”. Locate or protect
heatersoitcannotbedamagedbyamovingvehicle.
Page 5

COMBUSTIONAND VENTILATIONAIR
When installed, this gas appliance must be provided with fresh air for
combustion, ventilation, and dilution of hot flue gases. The minimum required
volume of the area where the appliance is installed should be 50 cubic feet per
1,000btu/hr.
If installed in an area of the home that is considered an unconfined space, the
natural infiltration of air around windows and doors will be adequate. If the
area is considered a confined space (less than 50 cubic feet per thousand btu),
fresh air can be supplied by providing two permanent openings into adjoining
rooms. Each opening shall have a minimum free area of one square inch per
1,000 btu per hour of the total input rating of all gas appliances in the confined
space, but not less than 100 square inches. One of the openings shall be within
12 inches of the ceiling and one within 12 inches of the floor. See Figure A.
If the home is of unusually tight construction (new and remodeled homes), free
air must be supplied through opening(s) to the outdoors. This can be
accomplished by providing 2 permanent openings, one commencing within 12
inches of the ceiling and one within 12 inches of the floor. These openings
shall communicate directly with the outdoors, or spaces that communicate
freely with the outdoors, such as a ventilated attic and crawl space through
galvanized or equivalent corrosion-resistant ducts. Exception: unobstructed
stud and joist spaces are acceptable ducts provided that not more than one fire
block is removed. Special provisions must be taken to insure that these stud
and joist spaces cannot be blocked with insulation or other objects. Each of
these openings using vertical ducts shall have a minimum free area of one
square inch per 4,000 btu/hr of total input rating of all gas appliances. See
FigureB and C. If horizontal ducts areused,the minimum free area shall beone
square inch per 2,000 btu/hr of total input rating of all gas appliances.
Fresh make-up air can also be provided through a duct to one permanent
openingcommencingwithin 12 inches of the ceiling. The minimumfreeareaof
this opening shall be one square inch per 3,000 btu/hr of the total input rating
of all gas appliances but not less than the sum of the areas of all vent connectors
in the space. See Figure D.
When calculating the amount of fresh air needed you must include make-up air
requirements for the operation of exhaust fans, kitchen ventilation systems,
clothes dryers, and fireplaces.
Additional information can be found in the latest edition of ANSI Z223.1
(NationalFuel Gas Code).
ALLCOMBUSTIONAIRFROM
ADJACENTINDOORSPACES
THROUGHINDOORCOMBUSTION
AIROPENINGS
UL Listed Vent Cap
UL Listed Gas Vent
Opening
Opening
ALL COMBUSTION AIR FROM
OUTDOORS. INLET AIR FROM
VENTILATED CRAWL SPACE AND
OUTLET AIR TO VENTILATED ATTIC
UL Listed Vent Cap
UL Listed Gas Vent
Ventilation Louvers
(each end of attic)
Outlet Air
Inlet Air
Ventilation
louvers for unheated
crawl space
ALL COMBUSTION AIR FROM OUTDOORS
THROUGH VENTILATED ATTIC ALL COMBUSTION AIR FROM OUTDOORS
THROUGH SINGLE COMBUSTION AIR OPENING
UL Listed Vent Cap
UL Listed Gas Vent
Ventilation Louvers
(each end of attic)
Outlet Air
Inlet Air Duct (Ends 1 Ft.
[300 mm] above floor)
UL Listed Vent Cap
UL Listed Gas Vent
Opening
Alternate
opening
location
FIGUREA
FIGUREC
FIGUREB
FIGURED
Page 6
Inlet
Grille
Inlet
Grille

CLEARANCES
If the area where the appliance is to be installed contains
carpeting, tile, or combustible materials, other than wood
flooring, the appliance shall be installed on a metal plate
(stoveboard), a wood panel, or other non-combustible
materials. The use of ceramic or quarry tile is acceptable
and provides an appealing surface that is easily cleaned.
This material is to extend 2 inches from each side and 12
inches from the front. It is advisable to extend this to the
wall behind the appliance.
Clearances to combustibles are as follows:
•From jacket to adjacent side walls, 2” on the 20/35, and
6” on the 50/70. Maintain adequate clearance on right
side for accessibility.
•From rear surface vertical vent pipe to rear walls – 6”.
•From rear of unit to rear wall, 13” on 20/35, and 14” on
the50/70.
•From top of heater to ceiling, 34” on the 20/35, and 31”
on the 50/70.
•Fromtop of heater toany overhanging projections such
as a mantle or window sill is 22” on the 20/35, and 19
inchesonthe50/70models, with a maximum horizontal
extension of 18 inches.
The clearances around the air opening into the combustion
chamber must be maintained, and the burner must be kept
clean.
Do not permit dust or dirt to accumulate here. The other
clearances previously mentioned must be maintained.
There must be adequate room provided and maintained
around the heater for accessibility and for the flow of
combustion and ventilation air.
Projection
Projection
CLEARANCES - VC20, VC35, VCR35
CLEARANCES - VC50 & VC70,
VCR50 & VCR70
Page 7
Ceiling
Wall
Floor
18 IN.
45.72CM
6 IN.
15.2CM
14IN.
35.6CM
31IN.
78.7CM
19 IN.
48.3CM
50/70
Projection
18 IN.
45.72CM
Ceiling
Wall
Floor
34 IN.
86.36CM 22 IN.
55.88CM
6 IN.
15.2CM
13IN.
33CM
20/35
Projection
DRAFTDIVERTER
The draft diverter must be installed in the same atmospheric
pressurezoneasthecombustionairsupplyforthe main burner.
DOOR KNOB
Remove from the inside of the casing door and assemble to
the outside of the door. VC201 and VC202 have finger holes
in the door in lieu of knob.

PILOTADJUSTMENT
The pilot flame can be observed by opening the pilot lighting
hole cover. The pilot flame should surround the top 3/8 to ½
inch of the thermocouple (see Figure 2). If the flame needs
adjusting,firstlocatethepilot adjustment screw cap and remove.
Adjustment screw is underneath (see Figure 1). To increase the
flame, turn the pilot adjustment screw counterclockwise .
To decrease the flame, turn the screw clockwise . NOTE:
The pilot is unregulated. If incoming line pressure is more than
7” w.c. Natural Gas or 11” w.c. for L.P. Gas, the pilot flame size
should be decreased.
PilotAdj.
Screw
FIGURE1
PILOTFLAME
ADJUST-
MENT
Pilotflame
should
envelop
3/8 to 1/2
inch on the
tip of the
generator.
FIGURE2
RADIANTSAND GLASSPANELS
FORALLVCRMODELS
(See Figure 9 – Replacement Parts Section)
INSTALLGLASSANDRADIANTSASFOLLOWS:
STEP1. Remove threescrews from under topof opening in
bezelframe assembly.
STEP2. Pull top of bezel down and lay aside.
STEP3. Remove glass from bottom pad in shipping carton.
STEP4. Remove carton containing radiants from cavity of
combustion chamber.
STEP5. Remove radiants from carton and install by tilting
backwards and lifting at the same time into opening. Place
the radiants on the burner radiants supports. The radiants
must be straight. Never operate heater if any radiant is
tilted to front or rear. Continued
STEP6. Install glass panels by inserting top edge into upper
retainer and lower into bottom support, and slide glass into
position. Do not allow a crack between the two glass panels.
Never operate heater with either glass missing or cracked.
STEP7. Re-install bezel byplacingbezeltabsover lower front
and swing bezel into position and secure with three screws.
MAIN BURNER ORIFICE
This appliance was shipped from the factory with an orifice
sized to give the correct gas input using the gas for which the
heater was equipped. There may be local conditions, such as
variation in gas pressure or BTU content of the gas, which
may be cause for a change in the orifice. The gas company
supplying the fuel or the installing contractor should check
the gas input rate.
If the rate exceeds the “BTUH INPUT” on the rating plate by
5%, the orifice should be replaced with a smaller orifice by a
qualified technician to reduce the input to the rating plate
value.
The input rate may need to be adjusted for elevation. See the
following charts to determine the correct orifice size for your
Model Number and elevation. These orifice sizes are based
on a heating value of 1020 for Natural Gas and 2500 for L.P.
Gas.
CAUTION: Aselevationincreases, derating is necessary for
the safe and proper operation of this heater. Do not increase
the Btu input rate by increasing the orifice size or gas
pressure. Allowforelevation derating when sizing gas heating
equipment.
SPECIFICELEVATIONS
Model 0 to 2,000- 4,000 - 6,000 - 8,000’
No. 2,000’ 4,000’ 6,000’ 8,000’ 10,000’
VC201 45 47 48 49 50
VC351 35 37 38 40 42
VC501 30 31 31 32 35
VC701 25 27 28 29 30
VCR351 35 37 38 40 42
VCR501 30 31 31 32 35
VCR701 25 27 28 29 30
ORDERKIT#49820 45-1HIGHALTITUDEKIT
SPECIFICELEVATIONS
Model 0 to 2,000- 4,000 - 6,000 - 8,000’
No. 2,000’ 4,000’ 6,000’ 8,000’ 10,000’
VC202 1.3mm 55 56 56 57
VC352 1.65mm 53 53 54 54
VC502 47 49 49 50 51
VC702 41 42 43 44 46
VCR352 1.65mm 53 53 54 54
VCR502 47 49 49 50 51
VCR702 41 42 43 44 46
ORDERKIT#49820 45-1HIGHALTITUDEKIT
NATURALGAS
L.P.GAS
Page 8
3/8 TO
1/2 INCH

CAUTION: There may be momentary and spasmodic
orangeflashes intheflame. Thisiscausedbytheburning
ofair borne dustparticles and isnot to beconfused with
theyellowtippingwhichisastableorpermanentsituation
whenthereisinsufficientprimaryair.
MAINTENANCE
CLEANING: To clean the front casing of your heater, it is
onlynecessary to use a soft cloth. Lightdustcan be removed
in this way. To obtain a polish or gloss, use a little light
machineoil on the cloth. Do not usemetalpolish or cleaning
solution. The burner ports should be kept free from lint and
dust.
CLEANINGOF COMBUSTIONCHAMBER
The combustion chamber of your console heater should
never need to be cleaned if proper burner adjustment and
gas pressures are maintained. However, if an unusual
circumstance should occur, the following procedure should
be followed in cleaning your combustion chamber.
1. Turn off gas supply to heater at manual valve in
supply line to heater.
2. Disconnect heater at ground joint union ahead of
main gas valve.
3. Remove main control and orifice assembly.
4. Remove burner.
5. Remove combustion chamber.
6. Using a scraper, scrape inside of a primary
combustion chamber. This should be area of
heaviest accumulation of carbon.
7. Remove plug bottom located in bottom rear of
second combustion chamber. Using a bottlebrush,
clean inside of this chamber. Shake residue out the
clean-out hole.
8. Clean the rear chamber by using bottlebrush
through the vent tube openings.
9. Replace combustion chamber, burner and control.
Checkallgaspipingforleaksbeforelighting heater.
Repair service should be performed by qualified persons.
The heater should be inspected before initial use. An annual
cleaning of control compartment and safety performance
check should be made by a qualified service person. More
frequent cleaning may be required when exposed to the
excessive lint conditions due to carpeting and bedding
material, etc. It is imperative that the control compartment,
burners, and circulating air passageways of the heater be
kept clean. Any safety screen, casing top, or guard removed
for servicing the heater must be replaced prior to operating
heater.
If the venting system is not maintained in proper operating
condition, the vent safety shutoff will not allow heater to
operate. Periodic examination of the entire venting system
as a routine part of the safety performance check is
recommended on an annual basis.
Itis advised that the pilot andmainburner flames be checked
at least twice during the heating season for any changes in
flame characteristics. See Figure 2 and Figure 3.
Page 9
FIGURE3
INNER MANTLE 1/4”
OUTER MANTLE 3 - 5”
PROPERBURNERFLAME
3” TO
5”
1/4”
SERVICERECORD
THIS IS A GAS-FIRED APPLIANCE, KEEP THE AREA CLEAR OF GASOLINE AND OTHER FLAMMABLE
VAPORS AND LIQUIDS. ALL COMBUSTIBLE MATERIAL MUST BE KEPT CLEAR OF THIS AREA.
HAVE A QUALIFIED SERVICEMAN CHECK THE BURNER PERIODICALLY. REMOVE AND CLEAN
IF NECESSARY.

10. Close pilot lighting hole cover and casing
door.
11. Turn gas control knob counterclockwise
to “ON”.
12. Turn temperature control knob to desired setting.
MODELS: VC201A, VC202A, VC351A, VC352A, VC501A, VC502A, VC701A,
VC702A, VCR351A, VCR352A, VCR501A, VCR502A, VCR701A, VCR702A
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you donot followtheseinstructions exactly,afire orexplosion may result
causingproperty damage,personalinjury orloss oflife.
A. This appliance has apilotwhich must be lighted byhand.
When lighting the pilot, follow these instructions ex-
actly.
B. BEFORELIGHTINGsmellallaround theappliancearea
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHATTODOIFYOUSMELLGAS:
•Do not try to light any appliance.
•Do not touch any electric switch; do not use any phone
in your building.
•Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
•Ifyoucannot reach your gas supplier, call thefiredepartment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand,don’t try to repair it, callaqualified service technician.
Force or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the information on the safety label.
2. Turn temperature control knob to “OFF” or it’s
lowest position.
3. Depress and turn gas control knob clockwise
to “OFF” position.
4. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the information on the
safety label. If you don’t smell gas, go to the next
step.
5. Open casing door and pilot lighting hole cover.
6. Findpilot. (Follow metalpilottubefrom gascontrol).
7. Locate red piezo ignitor button on top of heater.
8. Turn gas control knob counterclockwise to
“PILOT”.
9. Pushin gas control knob and hold in. Immediately
begin a series of pushing and releasing the red
piezo ignitor button, while observing the pilot.
Continue to spark until pilot is lit. Continue to
hold the gas control knob in for about one (1)
minuteafterthepilot is lit. Release the gas control
knob and it will pop back up. Pilot should remain
lit. If pilot goes out, repeat steps 3 thru 9.
• If knob does not pop up when released, STOP
andimmediately call your service technician
or gas supplier.
•If the pilot will not stay lit after several tries,
turn the gas control knob to “OFF” and call
your service technician or gas supplier.
TO TURN OFF GAS TO APPLIANCE
1. Turn the temperature control knob to it’s lowest setting.
2. Push in gas control knob slightly and turn clockwise to “OFF”. Do not force.
Gas Control Knob
NOTE: Knob can
not be turned from
“PILOT”to“OFF”
unless knob is
pushed in slightly.
Do not force.
Page 10
Pilot is located on
end of combustion
chamber above
burner.

Flame toolarge 1. Defective operator section of gas valve. 1. Replace complete valve.
2. Burner orifice toolarge. 2. See orifice chart to determine the correct orifice size
for your Model Number and elevation.
3. Pressure regulator malfunction. 3. Regulator must be adjusted by a qualified serviceman
using proper tools and instruments.
Noisy Flame 1. Noisy pilot. 1. Reduce pilot gas with adjusting screw on combination
gas. (Fig. 1).
2. Burr in orifice (if it whistles or resonates). 2. Remove burr or replace orifice (Do not enlarge orifice).
3. Excessive gas input. 3. See “Flame Too Large”, above.
Yellow tip flames (Some 1. Clogged main burner ports. 1. Clean main burner ports (Do not enlarge ports).
yellow tipping on LP Gas 2. Clogged draft hood. 2. Clean draft hood.
is permissible) 3. Linted up air shutter. 3. Check for dust or lint at air mixer opening and around
the shutter.
Floating Flame 1. Blocked venting. 1. Clean flue passageways to relieve blockage.
Gas Odor 1. Chimney or flue obstruction. 1. Clean flue.
2. Drafts around heater. 2. Eliminate drafts.
3. Gas leak. 3. Shut off gas service immediately. Check piping. Call
gas company. See “For Your Safety” (Page 1), and
“Gas Supply” (Page 3).
Delayed Ignition 1. Pilot flame too small. 1. Check pilot orifice, clean, increase pilot gas flow if
necessary by adjusting at combination control valve
(Fig. 1).
2. Burner ports clogged near pilot. 2. Clean burner ports (do not enlarge ports).
3. Low gas pressure. 3. Check gas supply pressure. See “Gas Supply”.
4. Pilot decreases in size when main 4. Supply piping is inadequately sized. Consult local gas
burners come on. utility or competent installer.
5. Drafts around unit. 5. Eliminate drafts.
6. Pilot lighter door open causing 6. Close pilot lighter door.
disturbance of pilot flame.
7. Improper venting. 7. See “Venting” (Page 2).
8. Pressure regulator malfunction. 8. Regulator must be adjusted by a qualified serviceman
using proper tools and instruments.
Failure to ignite 1. Main gas off. 1. Open all manual gas valves.
2. Defective gas valve. 2. Replace gas valve.
Condensation of 1. Improper venting. 1. See “Venting”.
water vapor.
Burner won’t turn off 1. Defective or sticking automatic valve. 1. Clean or replace valve.
2. Excessive gas pressure (The supply gas 2. To correct this situation contact the gas company
pressure must not exceed 1/2 psi or 14” supplying the gas. See “Gas Supply”.
water column).
Incorrect gas input 1. Gas input not checked. 1. Re-check gas input. See “Gas Supply”.
2. Clogged orifice. 2. Check orifices for clogging. If clogged, clean out the
hole carefully with a smooth wood toothpick. (Do not
in any way enlarge or distort it).
3. Pressure regulator. 3. Regulator must be adjusted by a qualified serviceman
using proper tools and instruments.
4. Thermostat capillary tube damaged. 4. Replace gas valve.
SYMPTOM POSSIBLECAUSES CORRECTIVE ACTION
TROUBLE SHOOTING CHART for qualified serviceman - MAIN BURNER
TROUBLE SHOOTING CHART - POOR HEATING RESULTS
Page11

Not enough heat 1. Heater undersized. 1. This is especially true when a dwelling or room is
enlarged. Have the heat loss calculated and compare
to the heater output (70% of input). Your gas company
or installer can supply you with this information. If
heater is undersized, replace with correct size unit.
2. Temperature dial set too low. 2. Raise setting of temperature dial. See “Lighting and
Shutting Down Instructions”.
3. Incorrect gas supply pressure. 3. Check gas supply pressure and regulator pressure as
outlined above.
Too much heat 1. Temperature dial set too high. 1. Lower setting of temperature dial. See “Lighting and
Shutting Down Instructions”.
2. Combination control valve sticks open. 2. Replace combination control valve.
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION
TROUBLE SHOOTING CHART - POOR HEATING RESULTS - Cont’d.
Burner won’t light 1. Pilot flame too large or too small. 1. Re-adjust pilot flame using adjustment on combination
control valves (See Fig. 1 & 1A).
2. Defective combination control valve. 2. Replace valve.
Pilot outage 1. Dirt in pilot orifice. 1. Clean pilot orifice with air or solvent, do not ream.
2. Pilot lighter door open. 2. Close pilot lighter door.
3. Defective automatic pilot section in 3. Replace combination control valve.
combination control valve.
4. Defective thermocouple. 4. Replace thermocouple.
5. Vent safety shut off system. 5. See “Venting” section.
Pilot will not stay lit 1. Pilot flame too large or too small. 1. Re-adjust pilot flame using adjustment on combination
when control knob control valves (See Fig. 1 & 1A).
is released 2. Defective thermocouple. 2. Replace thermocouple.
3. Defective gas valve. 3. Replace gas valve.
4. Loosen connections at spill switch or 4. Tighten connections.
ECO on gas valve.
TROUBLE SHOOTING CHART - AUTOMATIC PILOT & VALVE
Page 12

Page 13
CHB-3BLOWERINSTALLATION
STEP1. Run black wire and white wire that comes from bottom of junction box down through the heat shield. See Figure A.
STEP2. Insert junction box into opening in back of heater. Attach using four #8x1/2” black screws provided. See Figure A.
STEP3. Attach fan switch to fan switch bracket using two #8x1/2” plated, Phillip head screws provided. The 2” flange on the
bottom of bracket and terminals on the fan switch should be toward the back of the heater when properly installed.
STEP4. Locate the two engagement holes in base of heater. On a 35,000 Btu heater these holes are approximately 6-1/2” from the
backedge and right andleft holes are 5-1/4” and7-1/4” respectfully from the rightside (as viewed frombackof heater). On
a 50,000 Btu heater the holes are approximately 10-3/4” from the back edge and right and left holes are 5-3/8” and 7-3/8”
respectfully from the right side. Attach fan switch bracket to base using two #8x1/2” hex head screws provided. This will
require a ¼” socket and ratchet. See Figure A.
STEP5. Locate the blower opening and mounting tab on the base of the heater. Insert the front flange of the blower housing under
the mounting tab, lower the back of the blower down onto the base aligning the clearance holes in the blower base with the
engagement holes in the heater base. Secure the blower to the base with two #8 screws provided. See figure A.
STEP6. Connect black wire from junction box to right fan switch terminal. See Figure B.
STEP7. Connect white wire from junction box to white fan motor wire. See Figure B.
STEP8. Connect black wire from fan motor to left fan switch terminal. See Figure B.
STEP9. Turn variable speed control switch clockwise (as viewed from front of unit) to “OFF”.
STEP10. Plug power cord into 115 V. grounded receptacle.
STEP11. Turn variable speed control switchcounterclockwise (asviewedfrom front of unit) from“OFF” to “HIGH”. Blower
will now cycle on automatically when the switch temperature is met after the main burner comes on. The blower will
continue to run for a short period after the main burner goes off. Blower speed can be adjusted by setting the variable
speed control switch between high and low.
WARNING: This appliance is equipped with a three-prong (grounding) plug for your protection against shock hazard and should
be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this
plug.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.
BLACK
BLACK
WHITE
GREEN
MOTOR SPEED
CONTROL
WHITE
BLACK
FAN
SWITCH
MOTOR
“Ifanypartofthe original wire as suppied
withtheappliancemustbereplaced,it
mustbereplaced with a wireofat least
a105degree C temperaturerating.”
FIGUREB
Heat Shield
Junction
Box
Speed
Control
Power
Cord
Fan Switch
Bracket
Blower
Housing
Mounting Tab
FIGUREA

13 12
25
33
34
23
26
38
35
36
28
24
18
19
10
9
2
11
39
5
41
37
41
3
20
22
21
31
32
30
29b
29a
29c
29d
29e
28a
28b
MODELSINCLUDED:
VC/ Closed Front Circulators
VCR/RadiantFrontCirculators
CHB3Blower
VENTEDCONSOLEHEATER
Prices and specifications subject to
change without notice. All prices
areF.O.B. factory.
NOTICE: When ordering any
component in the control train
assembly, specify either
Honeywell or Robertshaw
components.
Page 14
50
43
51
47
44
46
53
45
49
42
48
17
16 15
REV.08/01
28c
Mr. Contractor, we only sell parts
through our wholesalers, but the prices
listed are for your convenience. For
prompt parts service, contact the
wholesaler from which you purchased
your Cozy heater. NOTE: Parts &
schematic drawings on current models
are shown at www.cozyheaters.com.

NAT. VC201A-R VC351,VCR351A-R VC501,VCR501A-R VC701, VCR701A-R
MODELNUMBER L.P. VC202A-R VC352,VCR352A-R VC502,VCR502A-R VC702,VCR702A-R
REF. PART LIST PART LIST PART LIST PART LIST
PART DESCRIPTION NO. NO. PRICE NO. PRICE NO. PRICE NO. PRICE
Valve, 7000ASTR-4, Nat. Gas 1 84090 $164.30 84090 $164.30 84090 $164.30 84090 $164.30
Valve, 7000ASTR-4, L.P. Gas 1 80088 $164.30 80088 $164.30 80088 $164.30 80088 $164.30
Pilot Assy. 0.140.504 L.P.Gas 2 80063 $22.90 80063 $22.90 80063 $22.90 80063 $22.90
Pilot Assy. 0.140.514 Nat.Gas 2 80062 $22.90 80062 $22.90 80062 $22.90 80062 $22.90
Manifold 3 80110 $16.40 80111 $16.80 80113 $17.50 80112 $17.10
Orifice Nut 4 80024 $2.50 80024 $2.50 80024 $2.50 80024 $2.50
Burner Orifice, Natural Gas 5 80025 $3.40 80058 $3.40 80119 $3.40 80169 $3.40
Burner Orifice, L.P. Gas 5 80027 $3.40 80060 $3.40 80120 $3.40 80167 $3.40
Pilot Lighting Hole Cover 9 45332 $1.60 45332 $1.60 45332 $1.60 45332 $1.60
Thermocouple 10 70096 $11.90 70096 $11.90 70096 $11.90 70096 $11.90
Pilot Tubing Assy. w/Fittings 11 70012 $6.60 70012 $6.60 70012 $6.60 70012 $6.60
Vent Safety Spill Switch/ VC 12 80103 $10.60 80104 $10.60 80104 $10.60 80099 $9.60
Vent Safety Spill Switch/ VCR 12 N/A N/A 80100 $10.60 80102 $10.60 80099 $9.60
Wiring Harness w/Bluebird 13 80190 $9.30 N/A N/A N/A N/A N/A N/A
Wiring Harness w/ECO Fitting 13 N/A N/A 80194 $10.30 80194 $10.30 80195 $10.70
Control Rod 15 45375 $5.90 45850 $6.20 45850 $6.20 47360 $6.50
Control Rod Grommet 16 80010 $1.20 80010 $1.20 80010 $1.20 80010 $1.20
Temperature Control Knob 17 80318 $4.40 80318 $4.40 80318 $4.40 80318 $4.40
Burner, Steel 18 80123 $50.70 80124 $53.40 80125 $53.40 80126 $57.10
Burner Mounting Plate Assy. 19 45817 $12.50 45817 $12.50 45817 $12.50 45817 $12.50
Casing Door 20 45125 $4.70 45605 $6.30 46445 $7.20 46445 $7.20
Casing Door Latch 21 80005 $1.20 80005 $1.20 80005 $1.20 80005 $1.20
Casing Door Knob 22 N/A N/A 80055 $1.60 80055 $1.60 80055 $1.60
Casing Left Side, w/Insulation 23 45102 $23.00 45590 $28.70 46430 $31.20 47140 $38.00
Casing Right Side w/Insulation 24 45112 $24.30 45600 $30.10 46440 $32.70 47150 $39.40
Casing, Back Assembly 25 45150 $20.10 45615 $40.10 45615 $40.10 47160 $44.30
Casing, Top Assy. w/Insulation 26 45050 $50.20 45550 $61.40 46400 $67.50 47100 $74.30
“VC” Casing Front with/Insulation 28 45070 $53.40 45560 $63.80 45560 $63.80 47110 $74.30
“VC” Casing Trim Top & Sides 28a 45073 $19.10 45563 $23.60 45563 $23.60 47113 $30.90
“VC” Casing Bottom Trim 28b 45074 $9.90 45564 $12.00 45564 $12.00 47114 $14.00
“VC” Casing Center Trim w/Clips 28c 45077 $8.00 45567 $9.90 45567 $9.90 47117 $12.00
“VCR” Bezel Assembly 29a N/A N/A 46060 $63.80 46060 $63.80 47610 $69.10
“VCR” Upper Front Panel with/Insulation 29b N/A N/A 46035 $28.40 46035 $28.40 47585 $36.40
“VCR” Lower Front Panel 29c N/A N/A 46040 $25.40 46040 $25.40 47590 $28.90
“VCR” Casing Upper Trim 29d N/A N/A 46045 $16.40 46045 $16.40 47595 $19.70
“VCR” Casing Lower Trim 29e N/A N/A 46047 $14.90 46047 $14.90 47596 $16.70
Cozy Logo Emblem N/A 80006 $9.30 80006 $9.30 80006 $9.30 80006 $9.30
Clips, for Cozy Emblem N/A 80007 $2.20 80007 $2.20 80007 $2.20 80007 $2.20
Casing Base Assembly 30 45175 $51.70 45640 $68.90 46460 $76.90 47180 $83.80
Leg Levellers (4 per heater) 31 80009 $1.50 80009 $1.50 80009 $1.50 80009 $1.50
Heat Exchanger, Closed Front 32 45200 $126.80 45675 $168.70 46500 $222.70 47200 $270.20
Heat Exchanger, Radiant Front 32 N/A N/A 46100 $174.20 46825 $220.50 47700 $282.20
Heat Exchanger Spacer N/A N/A N/A 45845 $1.80 45845 $1.80 45845 $1.80
Rear Leg, Heat Exchanger 32A N/A N/A 45760 $3.80 45760 $3.80 45760 $3.80
Draft Diverter Assembly 33 45300 $35.90 45785 $48.30 46560 $46.00 47295 $50.10
Gusset 34 *45195 $3.00 *45195 $3.00 *45195 $3.00 *45195 $3.00
Radiant Glass Panel, “VCR” Series 35 N/A N/A *80079 $16.40 *80079 $16.40 *80079 $16.40
Radiant for “VCR” Series (5 per htr.) 36 N/A N/A 80073 $15.20 80073 $15.20 80073 $15.20
Radiant Support Rail “VCR” Series 37 N/A N/A *46160 $4.90 *46160 $4.90 *46160 $4.90
Piezo Ignitor 38 80016 $5.70 80016 $5.70 80016 $5.70 80016 $5.70
Piezo Wire 39 80127 $3.80 80128 $4.00 80129 $4.40 80129 $4.40
Valve Support Bracket 41 45860 $5.10 45860 $5.10 45860 $5.10 45860 $5.10
Lighting Instructions N/A 91267 $1.90 91267 $1.90 91267 $1.90 91267 $1.90
BLOWER PARTS CHB-3 BLOWER
Speed Control Switch w/Knob & Dec 42 70111 $26.70
Fan Switch 43 80253 $7.40
Fan Switch Bracket 44 47840 $3.80
Power Cord 45 80202 $4.20
Motor Wiring Harness 46 80256 $3.80
Blower/Motor Assembly 47 80251 $56.30
Blower Gasket - 7-1/4" N/A *80257 $1.20
Blower Gasket - 4-5/8" N/A *80258 $1.20
Junction Box Assembly 48 47850 $12.70
Junction Box Cover 49 47870 $5.10
Blower Nozzle Assembly 50 47820 $13.30
Mounting Bracket 51 47835 $2.20
Blower Platform Assy. (70 only) N/A 47335 $16.40
HOW TO PROPERLY ORDER PARTS: In addition to part description and part number, please give model number,and type of gas used. This
information can be found on the rating plate that is attached to rear of heater.
MARCH 2005
Revised 12/03
*2 Required
Page 15

IMPORTANTSAFETY BULLETINONYOURGAS CONTROLANDPILOT LIGHT
SYSTEMFORHEATINGEQUIPMENT
WHATYOUDON’TKNOW CANHURTYOU.
Your pilot light system has been designed for safe and reliable operation. Although safety mechanisms
are built-in, the potential for hazard exists. This information is intended to help you avoid these hazards.
YOURGASCONTROL ANDPILOTLIGHT
SYSTEM
Your gas control and pilot light system has a
safety device whose purpose is to shut-off the
gassupply tothe applianceif thepilot lightgoes
out. If you have trouble lighting the pilot or
keepingit lit,itmay meanthat thissafetydevice
iswarningyou thatthereis aproblemwith your
system. Inspection and repairs or replacement
mustbemadebyatrainedgasservicetechnician.
TAMPERINGIS DANGEROUS
Thepilot safetysystemmay alsonot workif you
do not follow the lighting instructions carefully
orifyoutamperwiththegascontrolthat youuse
tolightthepilot. Tamperingwiththegascontrol,
particularly with tools, can damage the safety
mechanism in the control and can allow gas to
leak. Thiscanresultinafireorexplosioncausing
propertydamage,personalinjuryor death.
IFYOUSMELL GAS,DON’T LIGHTIT
IFYOUCAN’TLIGHTIT,
DON’TFIGHTIT!
THISIS NOTAN ADVERTISEMENT
WHAT TO DO IF YOU SMELL GAS . . .
••
••
•Donot tryto lightanyappliance.
••
••
•Donot touchany electricalswitch;do notuse
anyphoneinyourbuilding.
••
••
•Immediatelycallyour gassupplierfrom a
neighbor’sphone. Follow thegassupplier’s
instructions.
••
••
•Ifyou cannotreachyour gassupplier,call the
firedepartment.
Installationand servicemustbeperformedby a
qualified installer, service agency or the gas
supplier.
Donotstore or usegasolineor other flammable
vaporsand liquidsinthe vicinityof thisorany other
appliance.
CRITICALSAFETY POINTSTO REMEMBER. ..
••
••
•Your gas hasbeen odorizedso thatyou can
smellit. Always smellaround for gasbefore
lightingyourappliance.
••
••
•Sniff for L.P.-gas at floor level. LP-gas is
heavierthanairandmay temporarilyexistat
floorlevel.
••
••
•Ifyousmell gas, do notattempt to light the
pilot. Donot cause aspark byturning onor off
electricalswitches orappliances orby usingthe
phone. Turn offthe gas tothe appliancesand
callyourgas supplierfromanotherlocation.
••
••
•If your gas control has gotten wet as the result
offlooding orotherwetting, itmustbereplaced
immediatelyby atrained gasservice technician.
Watercan leadto damage ofthe internal safety
mechanismin thegas controland cancreate a
hazardouscondition.

The Louisville Tin & Stove Co. warrants to the
original user the accompanying product for the period
specified herein, provided said product is installed,
operated, maintained, serviced, and used according to the
instructionsand specifications accompanyingthe product.
AS OUTLINED IN OUR INSTRUCTIONS, ANY
WARRANTY CONSIDERATIONS ARE
CONTINGENT ON INSTALLATION BY A
QUALIFIEDINSTALLER(CONTRACTOR). SELF-
INSTALLATION IS NOT RECOMMENDED AND
MAYINVALIDATEYOURWARRANTY.
If within a period of one year from the date of
installation of the product, any part supplied by the
manufacturer proves to be defective due to workmanship
or material, it will replace such part, provided parts have
not been subjected to misuse, alteration, neglect, or
accidents. Theterm of the warranty forthe heat exchanger
is covered in Table A below. Any claim not made within
ten (10) days after the expiration of the warranty period
shall be deemed waived by the user.
The manufacturer shall have no liability or be
required to perform any obligation under this warranty
unless, when requested, the user returns, at the user’s
expense, the component or product claimed defective, to
themanufacturer for inspection,to enablethe manufacturer
to determine if the claimed defect is covered by this
warranty. No charges for freight, labor or other expenses
incurred in the repair, removal, or replacement of any
product or component claimed to be defective, will be
paid by the manufacturer to the user, and the
manufacturer will not be liable for any expenses
incurred, by the user, in remedying any defect in the
product. Service under this warranty is the responsibility
of the installer. In the event service under this warranty is
needed, the user of the product shall request such service
directly from the installer. If the user is unable to locate
the installer, the user should write directly to the
manufacturer, and the name of an alternative service source
will be supplied.
Theproduct safetyregistration card(packed inside
theappliance) must be completed andreturned to the factory.
THIS WARRANTY IS EXPRESSLY IN LIEU
OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED (WHETHER WRITTEN OR ORAL). ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR
OF FITNESS FOR A PARTICULAR PURPOSE IS
EXPRESSLY LIMITED TO THE DURATION OF THE
MANUFACTURER’S EXPRESS, WRITTEN
WARRANTY.
UNDER NO CIRCUMSTANCES SHALL THE
MANUFACTURER BE LIABLE FOR ANY SPECIAL,
INDIRECT OR CONSEQUENTIAL DAMAGES OR
EXPENSES ARISING DIRECTLY OR INDIRECTLY
FROM ANY COMPONENT OR FROM THE USE
THEREOF. THE REMEDIES SET FORTH HEREIN
SHALL BE THE EXCLUSIVE REMEDIES AVAILABLE
TO THE USER AND ARE IN LIEU OF ALL OTHER
REMEDIES.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS
MAY NOT APPLY TO YOU.
SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY
TO YOU.THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY, FROM STATE TO STATE.
TABLEA
Warranty for gas appliance heat exchangers only.
Product Warranty Period
Cozy Gas Fired Floor Furnace 10Years
Cozy Gas Fired Wall Furnace 10Years
Cozy Gas Fired Vented Console Heater 10Years
CozyGas Fired Direct Vent Heater 10Years
Cozy Gas Fired Counterflow Furnace 10Years
Cozy Gas Fired Counterflow Direct Vent Furnace 10Years
Cozy Gas Fired Mobile Home Direct Vent Furnace 10Years
CozyGas Fired Hi-EfficientDirect Vent Wall Furnace 10 Years
LIMITED WARRANTYLIMITED WARRANTY
LIMITED WARRANTYLIMITED WARRANTY
LIMITED WARRANTY
LOUISVILLE TIN AND STOVE COMPANY
P.O. Box 2767 - Louisville, Kentucky 40201-2767