Craftsman 486.24608 User manual

Owner's IVlanuai
®
FRONT U E
IVlodel No. 486.24608
Fits 917 Series LT/YT/GT Tractors
DO NOT RETURN TO STORE
For Missing Parts or Assembly
Questions Call 1-866-576-8388
,,iiiiiii-............... iiiiiiiiiiiiiill
CAUTION:
Before using this product, read
this manual and follow all Safety
Rules and
Operating Instructions.
,, Safety
,, Assembly
,, Operation
,, Maintenance
,, Parts
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
www.craftsman.com
PRINTED iN U.S.A. FORM NO. 42033 (02/05109)

WARRANTY .,_
CRAFTSMAN ONE=YEAR FULL WARRANTY
When assembled, operated and maintained according to
the supplied instructions, if this product fails due to a defect
in material or workmanship within one year from the date of
purchase, return it to any Sears store or other Craftsman outlet
in the United States for free replacement.
This warranty is void if this product is ever used for commercial
or rental purposes.
This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co., D817WA, Hoffman Estates, IL 60179
SAFETY
Any power equipment can cause injury ifoperated improperly
or if the user does not understand how to operate the
equipment. Exercise caution at all times when using power
equipment.
• Refer to your tractor owners manual for "Rules For
Safe Operation".
Look forthis symbol to point out important safety
precautions. It means -- Attention!! Become
alert!! Your safety is involved.
BEFORE YOU BEGIN
TOOLS REQUIRED
(2) 9/16" Wrenches (Socket wrench may be used)
CAUTION! Muffler is hot[ Allow engine to
cool down before proceeding with bumper
installation.
DETERMINE [FYOUR TRACTOR HAS ASINGLE SUSPENSION BRACKET
OR DUAL SUSPENSION BRACKETS .i)
SINGLE SUSPENSION
BRACKET
t
SUSPENSION
BRACKET
FIGURE 1A (page 3)
DUAL SUSPENSION BRACKETS
SUSPENSION BRACKET SUSPENSION
BRACKET
FIGURE 1B (page 5)
Look under the front of your tractor (Figure 1A & 1B). If there is a single mower deck suspension bracket located underneath
the middle of the front axle, continue on to INSTRUCTIONS FOR SINGLE SUSPENSION BRACKET TRACTORS on
page 3. If your tractor does not have a mower deck suspension bracket underneath the middle of the front axle, skip to
INSTRUCTIONS FOR DUAL SUSPENSION BRACKET TRACTORS on page 5.
2 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

iNSTRUCTiONS FOR SINGLE SUSPENSION BRACKET TRACTORS
STEP 1: (SEE FIGURE 2)
*Open parts bag labelled "A" and verify that all parts
are present.
NOTE: Place cardboard or a mat on work surface to prevent
scratching of parts removed from carton and tractor.
HARDWARE SHOWN FULL SiZE
EXCEPT WHERE NOTED
(not full size)
PARTS BAG "A"
STEP 2: (SEE FIGURE 3)
• Remove tractor hood. (Refer to tractor manual.)
Remove the browning shield as shown.
FIGURE 2
Ref. Part Qty. Description
A 43350 4 Carriage Bolt, 3/8-16 x 1"
B 44072 4 Whizlock Nut, 3/8"
C R19171616 4 Washer, 1/2"xl"
D 47674 4 Plug
66460 1 Bumper
REMOVE
BROWNING SHIELD
REMOVE
FRONT SCREWS
FIGURE 3
STEP 3: (SEE FIGURE 4)
Place plug on a work bench or solid table and push
end of bumper down onto plug. Repeat for remaining
plugs.
BUMPER
PUSH DOWN
WiTH EVEN
PRESSURE
WORK BENCH
OR SOLID TABLEI
STEP 4: (SEE FIGURE 5)
Place a washer onto a carriage bolt and then insert
the bolt into the second mounting hole from the front
of the tractor frame. Securely tighten a whizlock nut
onto the bolt on the outside of the tractor frame.
Repeat on other side of tractor.
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
CARRIAGE BOLT
AND WASHER
\
WHIZLOCK
NUT FIGURE 5
3

STEP 5: (SEE FIGURE 6)
*Spread ends of bumper enough to fit slots onto bolts
in rear mounting holes in tractor frame.
*The bumper has three mounting holes. The rear
holes provide the most clearance while the forward
holes provide a neater appearance. Use a hole that
provides enough clearance for the hood to stay in
raised position when opened. Place a washer onto
a carriage bolt and insert the bolt through the tractor
frame and into desired mounting hole on each side of
bumper. Secure with a whizlock nut.
iMPORTANT: Before fully tightening nuts, be sure
tractor hood will stay in raised position when opened.
CARRIAGE BOLT
AND WASHER
WHIZLOCK NUT FIGURE 6
STEP 6: (SEE FIGURE 7)
*Replace the browning shield using the front screws
you removed in Step 2.
REPLACE
FRONT SCREWS
REPLACE
BROWNING SHIELD FIGURE 7
4 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

iNSTRUCTiONS FOR DUAL SUSPENSION BRACKET TRACTORS
STEP 1: (SEE FIGURE 2)
*Open parts bags labelled "A" and "B" and verify that
all parts needed are present.
NOTE: Place cardboard or a mat on work surface to prevent
scratching of parts removed from carton and tractor.
NOTE: Not all hardware will be used. Unused parts may be
discarded after assembly
HARDWARE SHOWN FULL SiZE
EXCEPT WHERE NOTED
STEP 2:
e
e
(SEE FIGURE 3)
Remove tractor hood. (Refer to tractor manual.)
Remove an (LT) Lawn Tractor heat shield like the one
shown. Remove a (GT) Garden Tractor heat shield
like the one shown only if you need access to inside
of tractor frame during step 5.
iMPORTANT: Be sure to re-attach the heat shield after
bumper is installed.
Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE
Ref. Part Qty. Description
A 48894 2 Self Threading Bolt, 3/8-16 x 1-1/2"
B 43062 2 Hex Bolt, 3/8-16 x 1-1/2"
C 43001 4 Hex Bolt, 3/8-16 x 1"
D 44072 4 Whizlock Nut, 3/8"
E 43003 4 Lock Washer, 3/8"
F 47674 4 Plug
65932 1 Bumper
(LT) LAWN TRACTOR
REMOVE THIS
STYLE HEAT SHIELD
(GT) GARDEN TRACTOR
REMOVE THIS HEAT SHIELD
ONLY IF MUFFLER MUST BE
MOVED IN STEP 4.
jFIGORE 3
5

STEP 3: (SEE FIGURE 4)
*Place plug on a work bench or solid table and push
end of bumper down onto plug. Repeat for remaining
plugs.
BUMPER
PUSH DOWN
WITH EVEN
PRESSURE
WORK BENCH
OR SOLID TABLE
I
SHORT STEP
,_'_ PLUG (E)
_-_ FIGURE4
STEP 4: (SEE FIGURE 5)
*Remove any bolts present in front mounting holes in
side of tractor frame. If bolt will not screw out of hole,
check if a nut is present on bolt on inside of frame.
On GT tractors, if access to nut is blocked by a front
mounted muffler, slide muffler down exhaust tubes to
rest on top of browning shield.
iMPORTANT: Be sure to re-attach muffler and heat
shield after bumper is installed.
• If rear mounting holes in tractor frame are empty,
install hex bolts and whizlock nuts supplied in the
parts bags. See figure 5.
(LT) LAWN TRACTOR
REMOVE BOLT iNSTALL (C), (D) IF
iF PRESENT HOLE iS EMPTY
SUSPENSION BRACKET /
(LT) LAWN TRACTOR
REMOVE BOLT INSTALL(C), (D) IF
IF PRESENT HOLE IS EMPTY
SUSPENSION
BRACKET
(GT) GARDEN TRACTOR
EXHAUSTTUBES
MUFFLER
BROWNING SHIELD /
SUSPENSION BRACKET
\/
REMOVE BOLT
IF PRESENT
FIGURE 5
6 Call 1-866-576-8388 for missing parts or assembly help
DO NOT RETURN TO STORE

STEP 5: (SEE FIGURE 6)
*Spread ends of bumper enough to fit slots onto bolts
in rear mounting holes in tractor frame.
*The bumper has three mounting holes. The rear
hole provides the most clearance while the forward
holes provide a neater appearance. Use a hole
that provides enough clearance for hood to stay in
raised position when opened. Attach the bumper
using either standard hex bolts and whizlock nuts or
self threading bolts and lock washers. Use the self
threading bolts if standard hex bolts do not insert
freely into the hole in the tractor frame.
iMPORTANT: Before fully tightening bolts, be sure
tractor hood will stay in raised position when opened.
LAWN TRACTOR (LT) SHOWN
GARDEN TRACTOR (GT) iS SIMILAR
WHIZLOCK NUT (D)
FORBOLT(B)
(E)
FIGURE 6
Call 1-866-576-8388 for missing parts or assembly help 7
DO NOT RETURN TO STORE

Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME ®(1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
www.sears.com www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
www.sears.com 1-800-469-4663 (Canada) www.sears.ca
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR ®
1-800-361-6665 (Canada)
Au Canada pour service en fran£ais:
1-800-LE-FOYER M°
(1-800-533-6937)
www.sears.ca
® Registered Trademark /TMTrademark /sMService Mark of Sears Brands, LLC
® Marca Registrada /TM Marca de Fabrica /sM Marca de Servicio de Sears Brands, LLC
MD
Mc Marque de commerce /Marque depos6e de Sears Brands, LLC © Sears Brands, LLC