Craftsman 610.24489 User manual

CRRFTSM ®
PLASTIC UTILITY
DUMP CART
Model 610.24489
• 10 cu. ft. heaped capacity
• Durable, polyethelene body
• Easy dump
If you read and follow these instructions, this product
can be assembled in 55 minutes or less. If you don't read
these instructions, assembly may take over two hourst
TO MINIMIZE ASSEMBLY TIME:
DO NOT tighten fasteners until instructed to do so.
Illustrated items shaded red are the parts being
assembled in that instruction section.
Assemble unit on cardboard box to avoid scratches
or damage to parts.
For best results, two people are required for assembly.
If there are any missing
parts, or if you have any
questions on assembly,
operation, maintenance
or safety, please call
1-800-652-2321
All fasteners are readily
available for purchase at
your nearest Sears store
or local hardware store.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A
Visit our Craftsman website: www.sears.com/craftsman @ 01/2009 6000154-REV A 01/09

Bolt Bag Contents
I©
13
15
17 16
REF. NO.
13
14
15
16
17
PART NO.
300083
300084
300072
6000105
6000106
AMT.
1
3
4
2
2
DESCRIPTION
HITCH PIN
HAIRPIN COTTER PIN
3/4" AXLE WASHER
SPACER, LONG
SPACER, SHORT
18 19 20 21
REF. NO.
18
19
20
21
PART NO. AMT.
300054 32
3000711 12
300062 34
3000537 2
DESCRIPTION
5/16"-18 x 3/4" PAN HEAD BQL-r
5/16" USS FLAT WASHER
5/16"-18 KEPS NUT
5/16"-18 x 1" PAN HEAD BOLT
TOOLS SUGGESTED FOR ASSEMBLY
Large blade screwdriver
1/2" wrench and/or socket
cordless drill
SAFETY INSTRUCTIONS
Never exceed load capacity of cart - 325 Ibs.
When operating on slopes, use lowest ground speed and
limit load to 200 Ibs.
Do not carry passengers in cart.
Do not use this cart on public roads.
Operate up and down slopes, never across the face of slopes.
Avoid sudden turns or maneuvers.
MAINTENANCE & STORAGE
Periodically check all nuts and bolts for tightness.
Check tire pressure regularly.
Grease wheels at axle for longer life.
Keep cart clean and dry to prevent rust and corrosion.
Store inside a clean, dry area when not in use.
OPERATION
With cart attached to tractor pull back on latch bar.
Cart body will tilt backwards, dumping contents.
Once empty, pull cart body down until it latches.
Make sure to use the hairpin cotter with the hitch pin when
attaching to the tractor.
Follow all operating instructions in tractors owners manual.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 2.

Carton Contents
3
2
7
10
6
4812
II 9
REF. NO. PART NO. AMT. REF. NO. PART NO. AMT.
i I CA RT BODY i
2 1 FRONT SUPPORT BRACE 8 1 DRAWBAR ASSEMBLY
3 1 FRONT SUPPORT 9 2 WHEELS
4 2 _TCH ANGLE 10 ANGULAR SUPPORT
5 2 AXLE SUPPORT 11 1 ASSEMBLY MANUAL
6 4 AXLE HOLDER 12 6000108 BOLT BAG
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 3.

Front Support Sub-Assembly
Step 1. Attach LATCH ANGLE (4) to FRONT SUPPORT (3).
Step 2. Assemble FRONT SUPPORT BRACE (2) to FRONT SUPPORT (3).
10
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 4.

Axle Support Sub-Assembly
Step 3. Loosely bolt together two AXLE HOLDERS (6) as shown.
Bolts will be tightened after axle is installed.
Step 4. Repeat for other two plates.
6
2O
Finger tight at this time
18
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 5.

Undercarriage Assembly
Step 5. Secure Front Support Assembly (Page 4) and AXLE SUPPORTS (5) to CART BODY (1) as shown, making sure to use
flat washers (19) under the heads of ALL bolts (18 & 21) going through CART BODY (1).
NOTE: HolesA&B need bolt (21)
Finger tight at this time
FRONT SUPPORT
ASSEMBLY
5
2O
21
_18
USE FLA T WASHERS UNDER THE HEADS OF
THE BOLTS GOING THROUGH THE BODY.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 6.

Axle Holder Assembly
Step 6. Add AXLE HOLDER ASSEMBLIES (Page 5) to AXLE SUPPORTS with bolts (18) and keps nuts (20) as shown.
HOLDER ASSEMBLY
THESE BOLTS WILL BE
TIGHTENED AFTER AXLE
IS INSTALLED.
8
TIGHTEN THESE EIGHT
BOLTS ONLY AT THIS TIME.
2O
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 7.

Hitch Assembly
Step 7. Secure LATCH ANGLE (4) to DRAWBAR ASSEMBLY (8) with bolts (18) and kep nuts (20).
8
2O
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 8.

Add Axle, Drawbar & Wheels
Step 8. Slide AXLE (7) through AXLE HOLDER, large SPACER (16),
DRAWBAR ASSEMBLY (8), large SPACER (16) and other AXLE HOLDER.
Step 9. Center axle and tighten
all bolts at this time.
Step 10. Slide AXLE WASHER (15), /
small SPACER (17),
WHEEL (9), another AXLE
WASHER (15).
5
Step 11. Insert HAIRPIN CO-I-I-ER PINS (14
in axle.
Step 12. Set cart upright on wheels and
insert HITCH PIN (13) into DRAWBAR
ASSEMBLY (8) and secure with HAIRPIN
CO-I-I-ER PINS (13).
HOLDER
15
9
14
15
Tighten all bolts at this time
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 9.

Service Parts List- 610.24489
2
418 1
17
6
14
REF. PART NO.
1 6000026
2 6000022
6000025
4 6000024
6000028
6 6000029
6000030
8A 6000019
9 6000027
10 6000023
13 300083
14 300084
15 300072
16 6000105
17 6000106
18 300054
19 3000711
.15 20 300062
21 3000537
22 401111
23 401121
24 300131
25 300053
26 300061
27 300052
AMT.
1
1
2
2
4
1
1
4
2
2
32
12
34
2
1
1
1
2
1
DESCRIPTION
CART BODY
FRONT SU PPOR-I- BRACE
FRONT SU PPORT
LATCH ANGLE
AXLE SUPPORT
AXLE HOLDER
AXLE
DRAW BAR
WHEELS
ANGULAR SUPPORT
HITCH PIN
HAIRPIN CO-I-FER PIN
3/4" AXLE WASHER
SPACER, LONG
SPACER, SHORT
5/16"-1 x 3/4" PAN HEAD BOLT
5/16" USS FLAT WASHER
5/16"-18 KEPS NUT
5/16"-18 x 1" PAN HEAD BOLT
LATCH POST
HITCH BRACKET
LATCH SPRING
3/8"-16 x 4" HEX BOLT
3/8"-16 C-LOCK NUT
3/8"-16 x 3/4" HEX HEAD BOLT
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m. - 5 p.m.E.S.T.
Page 10.