Cres Cor AQUATEMP CO151FPWUA12B-Q1 User manual

®
JOB:
ITEM NO:
®
Page E-1.2
Sept., 2004
PASS-THRU AQUATEMP™/ROAST-N-HOLD™
GENTLE CONVECTION OVEN
MODEL CO-151-FPW-UA-12B-Q1
FEATURES AND BENEFITS:
• Roast, cook, bake, reheat and hold with precise temperature and
humidity control. Supplied with food probes to constantly monitor
and control internal food temperature throughout the cooking and
holding stages.
• Slow convected air system promotes natural browning for flavor
and seals in natural juices.
• Moist heat, dry heat or a combination of both allows for a
•variety of food preparation and holding.
• Full 8200 Watts of power allows for reheating of prepared
•meals or bulk items. Maximum temperature 350˚F. (176.5˚C.).
• 1850 Watt water heater with separate control and low water indicator.
• Energy Management Logic system electronically directs power to
where it’s needed most during different operating cycles.
• Pre-setting automatic controls for roasting and holding cycles
allows for unattended operation 24 hours a day.
• Roast and hold over 300 lbs. (136 kg.) of meat in just
•7 sq. ft. of floor space.
• Non-venting oven, permitted by most local codes, provides
•easy, inexpensive installation.
• 304 stainless steel construction throughout for ease of cleaning.
• Smooth interior coved corners prevent food particle/grease buildup.
• Pass-thru design allows easy access from preparation and
serving areas.
• Field reversible insulated Dutch doors prevent temperature •
•loss. Silicone door gaskets for proper seal. High temperature
ceramic magnetic latches for “easy open” and security during
•transport. Latches and hinges mounted inboard.
• Standard with right hand hinging; left hand hinging available
upon request.
• Recessed push/pull handles on both sides prevent damage
•to walls; allows easy maneuvering.
• Non-corrosive stainless steel wire universal angles accommodate a
large variety of pan sizes on adjustable 1-1/2" spacing. Supplied with
12 sets of angles and six raised wire grids.
• Heavy duty 5" swivel casters, two with brakes. Provides mobility
when fully loaded.
POWER UNIT OPTIONS:
• 8200 Watts, 208 Volts, 1 Phase, 60 Hz.
• 8200 Watts, 240 Volts, 1 Phase, 60 Hz.
• 8200 Watts, 208 Volts, 3 Phase, 60 Hz.
• 8200 Watts, 240 Volts, 3 Phase, 60 Hz.
CO-151-FPW-UA-12B-Q1
5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: [phone]
www.crescor.com
®
®
®
C
SANITATION
CLASSIFIED
CLASSIFIED TO
NSF4
ACCESSORIES and OPTIONS
(Available at extra cost):
Security Panel for Controls
Tempered Glass Door Windows
Key Lock Latches
Extra Wire Grids
Extra Universal Angles
Side Bumpers
Set of 5 preset menu item switches
(up to 10 presets allowed)
50 Cycle Service
oSee page E-10 for accessory details.

5925 Heisley Road • Mentor, OH 44060-1833
Phone: 877/CRESCOR • Fax: [phone]
www.crescor.com
©Crescent Metal Products, Inc. 1998 All rights reserved. Litho in U.S.A.
®
CO-151-FPW-UA-12B-Q1
In line with its policy to continually improve its products,
CRES COR reserves the right to change materials and
specifications without notice.
SHORT FORM SPECIFICATIONS
Cres Cor Pass-Thru AquaTemp Roast-N-Hold Convection
Oven Model CO-151-FPW-UA-12B-Q1. Removable power
unit 20 ga. 304 stainless steel, recessed control panel. Two
stainless steel probes, 1-1/2 and 6” long. Cabinet 22 ga. 304
stainless steel. Stainless steel internal frame; coved corner
interior. Dutch doors front and back, 22 ga. 304 stainless
steel, ceramic magnetic latch, heavy duty hinges. 16 ga.
stainless steel water reservoir, 4 gallon capacity. Fiberglass
insulation in sides 2”; back, doors and base 1-1/2”. (12) sets
universal angles for multiple pan sizes and spacing. One
piece base .125 aluminum. 5" swivel modulus casters,
Delrin bearings. Load capacity 250 lbs. each. 8200 Watts,
Volts, 60 Hz., Phase. 2 year parts warranty. Provide
the following accessories: __ . UL, CUL, UL
Sanitation listed.
CABINET:
• Body: 22 ga. 304 stainless steel.
• Reinforcement: Internal framework of 16 ga. stainless steel.
• Insulation: Fiberglass, thermal conductivity (K factor) is .23
•at 75˚F. 1-1/2" in back wall, doors, base; 2" in side walls.
• Water pan: 4 Gallons; 16 ga. stainless steel with 1850 Watt
•heater and with petcock drain; mounted to base.
• Drip trough: Formed 18 ga. stainless steel; mounted to lower
front and rear of cabinet; removable drip pan.
• Air tunnels (2): 20 ga. stainless steel, lift-out type, mounted
•on side walls.
• Push/pull handles (4): 7" vertical; recessed.
BASE:
• One piece construction, .125 aluminum.
• Casters: 5" dia., swivel, modulus tires, 1-1/4 wide, load cap.
•250 lbs. each, temp. range -45˚/+180˚F. Delrin bearings. Front
casters equipped with brakes.
DUTCH DOORS:
• Field reversible.
• Formed 22 ga. 304 stainless steel.
• Latches: Chrome plated zinc with composite handle, ceramic
•magnetic type; mounted inboard.
• Hinges: Heavy duty chrome plated zinc, mounted inboard.
• Gaskets: Perimeter type, silicone.
• Pan stops: Embossed.
PAN SLIDES:
• Stainless steel wire universal angles (.306 dia.) mounted on
•lift-out posts.
• 12 sets of angles adjustable on 1-1/2" centers.
• Grids (6): Nickel chrome plated steel, raised wire 17" x 25".
POWER REQUIREMENTS AVAILABLE:
• 8200 Watts, 208 Volts, 60 Hz., 1 phase, 39 Amps.,
•50 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 1 phase, 34 Amps.,
•50 Amp. service.
• 8200 Watts, 208 Volts, 60 Hz., 3 phase, 23 Amps.,
•30 Amp. service.
• 8200 Watts, 240 Volts, 60 Hz., 3 phase, 20 Amps.,
•30 Amp. service.
POWER UNIT COMPONENTS: (refer to above drawing)
• Body:Formed 304 stainless steel with black control panel, recessed
and tilted 7˚.
A) Thermostat (microprocessor)
• Holding up to 250˚F (121˚C)
• Cook/Retherm up to 350˚F(176.5˚C)
• Thermometer
B) Thermostat (humidity): Solid state
C) Switch: Lighted ON-OFF rocker type.
D)Pilot light for low water level.
• Power cord:Permanent, 8ft., 6/3 ga.with right angle plug.
• Air heaters (3): 2670 Watts each.
• Water heater: 1850 Watts.
• Blower motors (3).
• Vent fans (2).
• Fuses (2): 3 amp.
• Probes (2): 1-1/2” and 6”, stainless steel.
INSTALLATION REQUIREMENTS:
• Check local vent hood codes for mobile Roast-N-Hold ovens.
CRES COR PAN DIM “A” DIM “B” DIM “C” INSIDE DIMENSIONS WEIGHT
MODEL NO. CAP/ANGLES SIZE WIDTH DEPTH HEIGHT WIDTH DEPTH HEIGHT ACT.
12 SEE NOTE IN 28-3/4 37-3/4 73-1/2 21-1/4 26-1/2 58 LBS 403
CO-151-FPW-UA-12B-Q1 SETS BELOW MM 740 960 1870 540 675 1475 KG 183
NOTE: Refer to pan size chart at end of section.
ALL CONSTRUCTION IS RIVETED, WELDED AND FINISHED.
DETAIL OF
PAN SLIDE