Crestron 4 Series User manual

The Crestron® RMC4 provides a secure, high performance, cost-effective
4-Series™ control processor and interface for controlling and monitoring
a single display device, a small AV system, lighting and shading, climate
control, security, energy management, and many other specialized
applications. A small form factor allows the RMC4 to be placed just about
anywhere, with the option to attach it to a flat surface or DIN rail using
the included mounting bracket.
In the Box
1 RMC4, 4-Series Control System
Additional Items
1 Bracket, Mounting, Integrated DINRail Clip (4519035)
2 Screw, 6-32 x 3/8 in., Phillips(2007225)
2 Connector, 3-Pin (2003575)
2 Connector, 4-Pin (2003576)
1 Connector, 5-Pin (2003577)
Mount the Control System
The RMC4 can be mounted onto a flat surface or a standard DIN rail
using the included mounting bracket.
CAUTION:To prevent overheating, do not operate the RMC4 in an area
that exceeds the environmental temperature range (32 to 104°F or
0to40°C) for this device.
Optional rack mount and pole mount kits (not included)are also available
for use with the RMC4. For more information, refer to the RMK-IFE-1U
Installation Guide (Doc. 7627) and the PLMK-IFE-101 Installation Guide
(Doc. 7615).
SurfaceMounting
1. Detach the RMC4 from the mounting bracket by pulling the left and
right flanges of the bracket outward to release the tabs that hold the
RMC4 in place.
2. Attach the mounting bracket to the surface by using four appropriate
mounting screws (not included) through the four mounting holes on
the bottom of the bracket.
3. Align the slots on the bottom of the RMC4 with the tabs on the
mounting bracket.
4. Press the RMC4 into the bracket until it snaps into place.
1
RMC4 QuickStart
4-Series™ Control System

5. (Optional) Secure the RMC4 to the bracket using the two included
6-32x3/8 in. screws as shown in the following illustration. DINRail Mounting
1. Detach the RMC4 from the mounting bracket by pulling the left and
right flanges of the bracket outward to release the tabs that hold the
RMC4 in place.
2. Pull the DIN rail release tab downward using a flat-head screwdriver.
3. Position the DIN rail mounting tabs (located on the rear of the
bracket) over the top edge of the DIN rail.
4. Push the DIN rail release tab upward to lock the mounting bracket
onto the rail.
5. Align the slots on the bottom of the RMC4 with the tabs on the
mounting bracket.
6. Press the RMC4 into the bracket until it snaps into place.
NOTE:Do not use the included screws to secure the bracket to the
bottom of the RMC4 when mounting into a DINrail, as it will then not be
possible to remove the RMC4 from the DIN rail.
2
RMC4 QuickStart
4-Series™ Control System

Connect the Control System
Make all device connections as shown in the following illustrations.
Front Panel Connections
Rear Panel Connections
Observe the following when connecting the RMC4:
lPower is provided to the RMC4 by a single Ethernet cable. A Crestron
PoE (Power over Ethernet) power supply, such as the PWE-4803RU,
or a PoE-capable network switch is recommended (both not included).
lConnect the chassis ground lug to a known earth ground circuit (for
example, building steel) to ensure that the RMC4 is grounded properly.
lApply power after all connections have been made.
3
RMC4 QuickStart
4-Series™ Control System

COM1 Connections
Port RS-232 RS-4221RS-485
GGND GND GND2
TX TX(from RMC4) TX- (from RMC4) TX-/RX-
RX RX(to RMC4) RX+(from RMC4) Not used
RTS RTS(from RMC4) TX+(from RMC4) TX+/RX+
CTS CTS(to RMC4) RX- (to RMC4) Not used
1. RS-422 transmit and receive are balanced signals that require two lines plus a ground
in each direction. RXD+ and TXD+ should idle high (going low at start of data
transmission). RXD- and TXD- should idle low (going high at start of data
transmission). If necessary, RXD+/RXD- and TXD+/TXD- may be swapped to maintain
correct signal levels.
2. A ground terminal connection is recommended but not required.
Configure the Control System
The control system may be configured using the provided web
configuration interface. The interface can be accessed using the control
system IP address or the Crestron XiOCloud® service.
Configuration via IP Address
To access the web configuration interface using the control system
IPaddress:
NOTE:The control system ships with DHCPenabled. A DHCPserver is
required to access the web configuration interface via the device
IPaddress.
1. Connect the control system to the network.
2. Use the Device Discovery tool in Crestron Toolbox™ software to
discover the control system and its IP address on the network.
3. Enter the control system IPaddress into a web browser.
Configuration via Crestron XiOCloud
The Crestron XiO Cloud service allows supported Crestron devices across
an enterprise to be managed and configured from one central and secure
location in the cloud. Supported devices are configured to connect to the
service. Use of the service requires a registered Crestron XiO Cloud
account.
NOTE: The device may be disconnected from the service by navigating to
the Cloud Services tab in Crestron Toolbox software (Functions >
Device Info >Cloud Services). For details, refer to the Crestron Toolbox
help file.
To access the web configuration interface using the Crestron XiOCloud
service:
1. Connect the control system to the network.
2. Record the MAC address and serial number that are labeled on the top
of the control system. The MACaddress and serial number are
required to add the device to the service.
3. Do either of the following
lFor existing accounts, access the Crestron XiO Cloud service at
https://portal.crestron.io.
lFor new accounts, register for a Crestron XiO Cloud account at
www.crestron.com/xio-cloud-registration.
4. Claim the device to the service as described in the Crestron XiO Cloud
User Guide (Doc. 8214).
5. Select the device from the cloud interface to view its settings.
4
RMC4 QuickStart
4-Series™ Control System

Create an AdminAccount
The first time the web configuration interface is accessed, a dialog box is
displayed asking the user to create an admin account. A similar message
is displayed when connecting to the device in Crestron Toolbox software if
an admin account has not already been created.
To create an admin account:
1. Enter a username and password for the admin account in the
appropriate text fields.
CAUTION:Do not lose the username and password for the admin
account, as the device must be reset to factory settings to regain
access.
2. Click OK. A dialog box is displayed stating that enabling authentication
will restart the web session.
3. Click Yes to confirm and restart. The username and password created
in step 1 must be entered to regain access to the web configuration
interface.
NOTE:The username and password must also be entered when
connecting to CrestronToolbox or XPanel.
Set the Time Zone
The time zone must be set on the control system to ensure that the
correct time settings are pushed to controlled devices.
To set the time zone:
1. Access the web configuration interface using either the device
IPaddress or the Crestron XiOCloud service.
2. Navigate to Settings >System Setup.
3. Select the time zone where the control system is used from the Time
Zone drop-down menu.
4. Click Save Changes on the top right of the screen.
Pair with Apple HomeKit
The control system can be paired with Apple® HomeKit® technology to
enable communication between the control system and Apple HomeKit
devices and accessories.
For pairing instructions and to locate the unique QRcode required for
pairing, refer to the RMC4Product Information document
(Doc.8541)that shipped with the RMC4.
5
RMC4 QuickStart
4-Series™ Control System

Visit the Product Page
Scan the QR code to visit the product page.
RMC4
www.crestron.com/model/6510418
Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, 4-Series, Cresnet, Crestron Toolbox, and XiOCloud are either
trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. Apple and HomeKit are either trademarks or registered
trademarks of Apple, Inc. in the United States and/or other countries. Other
trademarks, registered trademarks, and trade names may be used in this document to
refer to either the entities claiming the marks and names or their products. Crestron
disclaims any proprietary interest in the marks and names of others. Crestron is not
responsible for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8513A
06/26/20
6
RMC4 QuickStart
4-Series™ Control System