Crestron DM-NVX-E30 User manual

DM NVX™ Network AV
Encoders/Decoders
DM-NVX-E30
DM-NVX-D30
DM-NVX-E30C
DM-NVX-D30C
Product Manual
Crestron Electronics, Inc.

Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
The product warranty can be found at www.crestron.com/legal/sales-terms-conditions-warranties.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/legal/open-source-software.
Crestron, the Crestron logo, 3-Series, Crestron Toolbox, Crestron XiO Cloud, DigitalMedia, DM NVX, and DM NVX Director
are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries.
Dolby and Dolby Atmos are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or
other countries. DTS HD and DTS:X are either trademarks or registered trademarks of DTS, Inc. in the United States and/or
other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the
United States and/or other countries. Active Directory is either a trademark or registered trademark of Microsoft
Corporation in the United States and/or other countries. DisplayPort is either a trademark or registered trademark of Video
Electronics Standards Association in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors
in typography or photography.
©2019 Crestron Electronics, Inc.

Product Manual – DOC. 8425A Contents •i
Contents
Introduction...................................................................................................................................1
Physical Description.................................................................................................................... 2
DM-NVX-E30 and DM-NVX-D30 ........................................................................................................... 2
Front Panel, DM-NVX-E30................................................................................................................ 2
Front Panel, DM-NVX-D30 ............................................................................................................... 3
Rear Panel, DM-NVX-E30 and DM-NVX-D30...............................................................................4
DM-NVX-E30C ...........................................................................................................................................5
DM-NVX-D30C...........................................................................................................................................6
Configuration and Status.......................................................................................................... 7
DMF-CI-8 Chassis Details........................................................................................................................ 7
Using the Web Interface.................................................................................................................... 7
Using SIMPL Windows .......................................................................................................................8
DM NVX Director Virtual Switching Appliance....................................................................................8
Stream Statistics.......................................................................................................................................9
Using the Web Interface....................................................................................................................9
Using SIMPL Windows .....................................................................................................................10
Multicast TTL (Time-to-Live).................................................................................................................10
Using the Web Interface..................................................................................................................10
Using SIMPL Windows ......................................................................................................................11
DSCP (Differentiated Services Code Point) ...................................................................................... 12
EDID (Extended Display Identification Data).................................................................................... 13
Subscriptions ............................................................................................................................................ 14
Using the Web Interface.................................................................................................................. 14
Using SIMPL Windows ..................................................................................................................... 15
7.1 Surround Sound Audio ...................................................................................................................... 15
Analog Audio Output .............................................................................................................................. 16
Using the Web Interface.................................................................................................................. 16
Using SIMPL Windows ..................................................................................................................... 16
Crestron XiO Cloud Service Connection ............................................................................................. 17
Enterprise-Grade Security ..................................................................................................................... 18
IEEE 802.1X Authentication ............................................................................................................ 18
Authentication Management ......................................................................................................... 19
Fan Control .............................................................................................................................................. 20
Using the Web Interface................................................................................................................. 20
Using SIMPL Windows .................................................................................................................... 20
Automatic Firmware Update ................................................................................................................ 21

ii •Contents Product Manual – DOC. 8425A
HDCP 2.2 Compliance............................................................................................................... 22
IGMP Snooping .......................................................................................................................... 23
Troubleshooting......................................................................................................................... 25
Appendix: Device Discovery..................................................................................................... 27

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •1
Introduction
Crestron® DM NVX™ network AV encoders/decoders transport ultra high-definition 4K
video with 60 Hz frame rates and 4:4:4 color sampling over standard Gigabit Ethernet.
Support for High Dynamic Range (HDR) video and HDCP 2.2 ensures high picture quality
and compatibility with a variety of media sources. Using Pixel Perfect Processing
technology, a video signal is encoded and decoded to achieve imperceptible end-to-end
latency of less than 1 frame.
DM-NVX-E30(C) devices consist of the DM-NVX-E30 surface-mountable endpoint
and the DM-NVX-E30C card, which function as encoders (transmitters) only.
DM-NVX-D30(C) devices consist of the DM-NVX-D30 surface-mountable endpoint and
the DM-NVX-D30C card, which function as decoders (receivers) only. Compact in design,
the DM-NVX-E30 and DM-NVX-D30 are designed to fit in various locations, for example,
behind a flat panel display. The DM-NVX-E30C and DM-NVX-D30C are designed to
occupy the DMF-CI-8 card chassis.
NOTES:
•The DM-NVX-D30 and DM-NVX-D30C do not support scaling.
•DM-NVX-E30(C) encoders and DM-NVX-D30(C) decoders are compatible with
DM-NVX-350(C), DM-NVX-351(C), and DM-NVX-352(C) encoders/decoders.
If DM-NVX-E30(C) encoders are used with DM-NVX-35x(C) devices, the
DM-NVX-35x(C) devices must be in Receiver mode. If DM-NVX-D30(C) decoders are
used with DM-NVX-35x(C) devices, the DM-NVX-35x(C) devices must be in
Transmitter mode.
This manual provides information about the following:
•Physical description
•Configuration and status
•HDCP 2.2 compliance
•IGMP snooping
•Troubleshooting
In addition, information about device discovery of a DM NVX device using Crestron
Toolbox™ software is provided in the appendix of this manual. For installation
information, refer to the DM-NVX-E30/DM-NVX-D30 Quick Start (Doc. 8211) and the
DM-NVX-E30C/DM-NVX-D30C Quick Start (Doc. 8346) as applicable. For information
about designing a DM NVX system, refer to the DM NVX System Design Guide
(Doc. 7977). The documents are available at www.crestron.com/manuals.

2•DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Physical Description
The following sections provide information about the connectors, controls, and indicators
that are available on the DM-NVX-E30(C) and DM-NVX-D30(C) devices.
DM-NVX-E30 and DM-NVX-D30
This section provides information about the front and rear panels of the DM-NVX-E30
and DM-NVX-D30.
Front Panel, DM-NVX-E30
The following illustration shows the front panel of the DM-NVX-E30.
DM-NVX-E30 Front Panel
CONSOLE: Micro USB connector, female;
USB 2.0 computer console port for setup
NV LED:Green LED, indicates that the device is encoding (transmitting)
network video
OL LED: Green LED, indicates an online connection to a control system via Ethernet
LAN: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;1
PoE+ PD (powered device) port compatible with a PoE+ compliant Ethernet switch, a
Crestron DM-PSU-ULTRA-MIDSPAN, or an approved third-party PSE;
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity
HDMI INPUT LED: Green LED, indicates sync detection at the HDMI® input
HDMI INPUT: HDMI Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort™ interface
compatible)2, 3
1The LAN port must connect to a 1000BASE-T switch in order to stream network video.
2The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI or
Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are sold separately.
3Device control via CEC (Consumer Electronics Control) requires the use of a Crestron 3-Series® or later
control system.
    


Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •3
AUDIO: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
NOTE: The analog audio output is functional only when the DM-NVX-E30 is receiving
a 2-channel stereo input signal.
Front Panel, DM-NVX-D30
The following illustration shows the front panel of the DM-NVX-D30.
DM-NVX-D30 Front Panel
CONSOLE: Micro USB connector, female;
USB 2.0 computer console port for setup
NV LED: Green LED, indicates that the device is decoding (receiving) network video
OL LED: Green LED, indicates an online connection to a control system via Ethernet
LAN: 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;1
PoE+ PD (powered device) port compatible with a PoE+ compliant Ethernet switch, a
Crestron DM-PSU-ULTRA-MIDSPAN, or an approved third-party PSE;
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity
HDMI OUTPUT LED: Green LED, indicates video signal transmission at the
HDMI output
HDMI OUTPUT: HDMI Type A connector, female;
HDMI digital video/audio output (DVI compatible)2, 3
AUDIO: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
NOTE: The analog audio output is functional only when the DM-NVX-D30 is receiving
a 2-channel stereo input signal.
1The LAN port must connect to a 1000BASE-T switch in order to stream network video.
2The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cables are sold separately.
3Device control via CEC requires the use of a Crestron 3-Series or later control system.
  


4•DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Rear Panel, DM-NVX-E30 and DM-NVX-D30
The following illustration shows the rear panel of the DM-NVX-E30 and DM-NVX-D30.
DM-NVX-E30 and DM-NVX-D30 Rear Panel
PWR: Bicolor green/amber LED, indicates operating power supplied via the power
pack (sold separately), PoE+ compliant Ethernet switch, or injector/PSE;
Lights amber while booting and green when operating
SETUP: Push button for on-screen display of IP address;
Red LED, indicates that the SETUP button is pressed and times out automatically.
NOTES:
•If the DM-NVX-D30 decoder is connected to a DM-NVX-E30(C) or
DM-NVX-35x(C) encoder, pressing the SETUP button on the DM-NVX-D30
for less than 10 seconds displays the decoder and encoder IP addresses.
The IP addresses are shown on the display connected to the HDMI output of
the decoder.
•If the DM-NVX-E30 encoder is connected to a DM-NVX-D30(C) decoder, pressing
the SETUP button on the DM-NVX-E30 for less than 10 seconds displays the
encoder and decoder IP addresses. The IP addresses are shown on the display
connected to the HDMI output of the decoder.
•If the DM-NVX-E30 encoder is connected to a DM-NVX-35x(C) decoder,
pressing the SETUP button on the DM-NVX-E30 displays the IP address of the
decoder only. The IP address is shown on the display connected to the HDMI
output of the decoder.
RESET: Recessed push button for hardware reset
IR 1–2: 4-pin 3.5 mm detachable terminal block;
Comprises two IR/serial ports∗
IR output up to 1.1 MHz;
1-way serial TTL/RS-232 (0–5 volts) up to 19200 baud;
Crestron IRP2 emitter sold separately
COM: 5-pin 3.5 mm detachable terminal block;
Bidirectional RS-232 port;*
Up to 115.2k baud, hardware and software handshaking support
∗Device control via RS-232 and IR requires the use of a Crestron 3-Series or later control system.
     


Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •5
24VDC 2.0A: 2.1 x 5.5 mm DC power connector;
24 VDC power input;
Power pack included
Ground: 6-32 screw, chassis ground lug
DM-NVX-E30C
The following illustration shows the connectors, controls, and indicators that are
available on the DM-NVX-E30C.
DM-NVX-E30C
CONSOLE: Micro USB connector, female;
USB 2.0 computer console port for setup
NV LED: Green LED, indicates that the device is encoding (transmitting)
network video.
OL LED: Green LED, indicates an online connection to a control system via Ethernet
LAN: 100BASE-TX/1000BASE-T Ethernet port;1
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity
HDMI INPUT LED: Green LED, indicates sync detection at the HDMI input
HDMI INPUT: HDMI Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface
compatible)2, 3
AUDIO: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
NOTE: The analog audio output is functional only when the DM-NVX-E30C is
receiving a 2-channel stereo input signal.
1The LAN port must connect to a 1000BASE-T switch in order to stream network video.
2Device control via CEC requires the use of a Crestron 3-Series or later control system.
3The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI or
Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are sold separately.
     

6•DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
DM-NVX-D30C
The following illustration shows the connectors, controls, and indicators that are
available on the DM-NVX-D30C.
DM-NVX-D30C
CONSOLE: Micro USB connector, female;
USB 2.0 computer console port for setup
NV LED: Green LED, indicates that the device is decoding (receiving) network video.
OL LED: Green LED, indicates an online connection to a control system via Ethernet
LAN: 100BASE-TX/1000BASE-T Ethernet port;1
Green LED indicates Ethernet link status;
Amber LED indicates Ethernet activity
HDMI OUTPUT LED: Green LED, indicates video signal transmission at the
HDMI output
HDMI OUTPUT: HDMI Type A connector, female;
HDMI digital video/audio output (DVI compatible)2, 3
AUDIO: 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: 200 Ohms balanced, 100 Ohms unbalanced;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
NOTE: The analog audio output is functional only when the DM-NVX-D30C is
receiving a 2-channel stereo input signal.
1The LAN port must connect to a 1000BASE-T switch in order to stream network video.
2Device control via CEC requires the use of a Crestron 3-Series or later control system.
3The HDMI connection requires an appropriate adapter or interface cable to accommodate a DVI signal.
CBL-HD-DVI interface cables are sold separately.
   
 

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •7
Configuration and Status
This section provides information about configuring or viewing the following items using
the web interface and SIMPL Windows as applicable:
•DMF-CI-8 chassis details
•DM NVX Director™ virtual switching appliance
•Stream statistics
•Multicast TTL (Time-to-Live)
•DSCP (Differentiated Services Code Point)
•EDID (Extended Display Identification Data)
•Subscriptions
•7.1 surround sound audio
•Analog audio output
•Crestron XiO Cloud™ service connection
•Enterprise-grade security
•Fan control
•Automatic firmware update
DMF-CI-8 Chassis Details
NOTE: DMF-CI-8 chassis details apply to the DM-NVX-E30C and DM-NVX-D30C only.
A DM NVX card occupies a DMF-CI-8 chassis. Information about the chassis can be
viewed using the web interface or SIMPL Windows.
Using the Web Interface
View DMF-CI-8 chassis information on the Status page. The Chassis Details section
displays the following information:
•Serial number of the chassis
•Number of the slot into which the card is installed

8•DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Status Page – Chassis Details
Using SIMPL Windows
Using the top-level programming slot for the DM NVX card, program the
<ChassisSerialNumber_F>serial output join to report the serial number of the chassis.
Program the <CardSlotInfo_F> serial output join to report the number of the slot into
which the card is installed.
DM NVX Director Virtual Switching Appliance
If a DM NVX device is managed by a DM NVX Director™ virtual switching appliance,
information about the appliance can be viewed using the web interface.
View DM NVX Director appliance information on the Status page. The DM NVX Director
section displays the following information:
•DM NVX Director hostname
•Domain name, number, and slot number to which the DM NVX device is assigned

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •9
Status Page – DM NVX Director
Stream Statistics
Statistics can be displayed to indicate the number of packets received or transmitted,
the number of dropped packets, and the bit rate of the received stream. To enable or
disable stream statistics, use the web interface or SIMPL Windows as discussed in the
following sections.
Using the Web Interface
Configure stream statistics on the Stream page. In the Statistics section of the page,
set Statistics to Enable or Disable. To reset statistics, click Reset Statistics.
For additional information, refer to the online help of the web interface.
NOTE: The bit rate of the stream appears on the Stream page of the DM-NVX-D30 and
DM-NVX-D30C only.
Stream Page - Statistics Configuration

10 •DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Using SIMPL Windows
For the DM-NVX-E30 and DM-NVX-E30C, configure stream statistics in Slot-01:
Stream Transmit. For the DM-NVX-D30 and DM-NVX-D30C, configure stream
statistics in Slot-02: Stream Receive. Trigger the <StatisticsEnabled>digital input join
to enable the reporting of statistics. To disable statistics, trigger the
<StatisticsDisabled>digital input join. To clear the statistics, trigger the
<ResetStatistics> digital input join. The corresponding serial joins are updated when the
digital input joins are triggered. For additional information, refer to the SIMPL Windows
help file.
Multicast TTL (Time-to-Live)
NOTE: Multicast TTL configuration is applicable to the DM-NVX-E30 and
DM-NVX-E30C only.
Multicast TTL provides the ability to limit or extend the hop limit of a DM NVX stream
that traverses routers. In IPv4 multicasting, routers have a TTL threshold assigned to
each interface. Only multicast packets with a TTL greater than the threshold of the
interface are forwarded.
Multicast TTL can be set to any value ranging from 1to 255. The default setting is 5.
To set a multicast TTL value, use the web interface or SIMPL Windows.
Using the Web Interface
Configure multicast TTL on the Stream page. In the Advanced section of the page, set a
multicast TTL value:
1. Set Auto Initiation to Disabled.
2. Stop the stream by clicking Stop.
3. Select the Custom TTL checkbox.
4. Enter the desired TTL value (1to 255).
5. Set Auto Initiation to Enabled. The stream automatically restarts.
NOTE: Deselecting the Custom TTL checkbox returns the TTL value to the
default setting.

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •11
Stream Page - Multicast TTL Configuration
Using SIMPL Windows
Configure multicast TTL as follows:
1. Using the top-level programming slot:
a. Trigger the <AutomaticInitiationDisabled> digital input join.
b. Trigger the <Stop> digital input join.
2. In Slot-01: Stream Transmit, set the <MulticastTTL> analog input join to the
desired value (1to 255).
3. Using the top-level programming slot, trigger the <AutomaticInitiationEnabled>
digital input join. The stream automatically restarts.
For additional information, refer to the SIMPL Windows help file.

12 •DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
DSCP (Differentiated Services Code Point)
NOTE: DSCP configuration is applicable to the DM-NVX-E30 and DM-NVX-E30C only.
To implement Quality of Service (QoS), IP networks use the DSCP value. Within an
IP packet header, the DSCP defines a value from 0 to 63 that maps to a certain traffic
classification. Based on IT department policies, DSCP values are used within a network
to determine the treatment of packets in router queues, the routes of traffic flows, and
per-hop behavior. By default, DSCP is set to 32.
NOTE: Change the DSCP default setting of 32 only if required by IT department policies.
Configure DSCP on the Stream page. In the Advanced section of the page, set a
DSCP value:
1. Set Auto Initiation to Disabled.
2. Stop the stream by clicking Stop.
3. Select the Custom DSCP checkbox.
4. Enter the desired DSCP value (0to 63).
5. Set Auto Initiation to Enabled. The stream automatically restarts.
NOTE: Deselecting the DSCP checkbox returns the DSCP value to the default setting.
Stream Page - DSCP Configuration

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •13
EDID (Extended Display Identification Data)
NOTE: EDID configuration is applicable to the DM-NVX-E30 and DM-NVX-E30C only.
EDID configuration allows management of the EDID that is to be sent to the upstream
device connected to the HDMI input of the DM NVX device. If an EDID other than the
default EDID is desired, use the web interface to configure the EDID.
Configure EDID on the HDMI INPUT page. In the EDID section of the page, select the
desired EDID. For additional information, refer to the online help of the web interface.
HDMI INPUT Page - EDID Configuration

14 •DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Subscriptions
NOTE: Subscription configuration is applicable to the DM-NVX-D30 and
DM-NVX-D30C only.
Subscription of a DM NVX encoder to a DM NVX decoder sets up Real Time Streaming
Protocol (RTSP) negotiation between the DM NVX decoder and the DM NVX encoder.
When a stream is routed, the DM NVX decoder performs the Internet Group
Management Protocol (IGMP) join, which causes the decoder to join the multicast group
of the encoder. A maximum of 64 encoders can be subscribed to a single decoder.
To configure subscriptions, use the web interface or SIMPL Windows as discussed in the
following sections.
Using the Web Interface
Configure subscriptions on the Subscriptions and Routing pages:
1. On the Subscriptions page, do either of the following:
a. In the Subscribed Streams section, manually add each encoder that is to be
subscribed to the decoder or load one or more existing subscription lists
(*.xml). The default filename of the subscription list is subscription.xml.
NOTE: Subscribed transmitters can be reordered in the list. To do so, click the
encoder that is to be reordered in the list, and then click the up arrow
( ) or the down arrow ( ) until the encoder appears in the desired
location in the list.
b. In the Available Streams section of the page, click Subscribe Checked or
Subscribe for the encoders that are to be subscribed to the decoder.
Subscriptions Page

Product Manual – DOC. 8425A DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders •15
2. In the DM NVX Routing section of the Routing page, select the desired encoder to
be routed to the decoder.
Routing Page
For additional information, refer to the online help of the web interface.
Using SIMPL Windows
NOTE: Selection of the encoders for subscription or selection of subscription lists can be
performed using the web interface only.
Manually select a subscribed encoder for routing in Slot-1000: XIO Routing. Set the
<VideoOut> analog input join to the desired encoder. For additional information, refer to
the SIMPL Windows help file.
7.1 Surround Sound Audio
DM NVX devices support the lossless transport of 7.1 surround sound audio, which
includes Dolby® TrueHD, Dolby Atmos®, DTS HD®, DTS:X® and uncompressed linear PCM
audio formats.
NOTE: The DM-NVX-D30 and DM-NVX-D30C cannot accept downmixed audio from a
DM-NVX-351 or DM-NVX-351C transmitter.
To configure 7.1 surround sound audio, set the desired EDID (refer to "EDID" on page 13).

16 •DM-NVX-E30(C)/DM-NVX-D30(C) Encoders/Decoders Product Manual – DOC. 8425A
Analog Audio Output
The analog audio output can provide a stereo line-level signal to feed a local sound
system or sound bar. The output volume is adjustable via the web interface or
SIMPL Windows.
Using the Web Interface
Configure the volume of the analog audio output on the Output page. Set Analog Audio
Volume to the desired volume.
Output Page - Analog Settings Configuration
For additional information, refer to the online help of the web interface.
Using SIMPL Windows
Using the top-level programming slot for the DM NVX device, set the
<AnalogAudioOutputVolume> analog input join to the desired volume. For additional
information, refer to the SIMPL Windows help file.