Crestron DM NVX Series User manual

The Crestron® DM-NVX-350C,DM-NVX-351C, and DM-NVX-352C
network AV encoder/decoder cards transport ultra high-definition 4K60
4:4:4 HDR video over standard Gigabit Ethernet.
In the Box
1 DM-NVX-350C, DM-NVX-351C, or DM-NVX-352C
Network AV Encoder/Decoder Card
Additional Item
1 Connector, 5-Pin (2003577)
Install the Card
The DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C are designed to
occupy the DMF-CI-8 chassis.
CAUTIONS: To prevent bodily injury when mounting or servicing the
unit in a rack, observe the following guidelines:
lDM NVX® cards are susceptible to damage from electrostatic
discharge (ESD). Observe standard ESD precautions when
handling the cards. Wear an ESD wrist strap that is connected to
ground, and place the cards on grounded surfaces only.
lTo prevent damage to a card that is connected to cables,
disconnect all cables from the card before installing the card into a
card slot or removing the card.
NOTES:
lIn a new installation of the DMF-CI-8, it is recommended that the
cards be installed before power is applied to the chassis. In an
existing installation of the DMF-CI-8, the cards can be added or
replaced without the need to shut down the chassis—the cards are
hot swappable.
lWhen installing the cards into a partially populated DMF-CI-8,
install the cards into slots 5–8 before using slots 1–4. Doing so
ensures better cooling and lower power consumption. In addition,
always cover empty slots using the filler plates included with the
chassis.
To install a card into the DMF-CI-8:
1. Using a #2 Phillips screwdriver (not included) or your fingers, remove
the filler plate of an unused slot by loosening the two captive panel
screws.
2. Carefully insert the card into the card guides of the selected slot, and
then push the card inward until it engages the chassis backplane.
1
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

3. Finger-tighten the two captive panel screws to secure the card—do
not overtighten the screws.
Connect the Card
Connect the card as required for the application.
NOTES:
lThe cards can be configured to use either the DEVICE port or the
HOST port. Both ports cannot be used simultaneously.
lThe DM-NVX-350C and DM-NVX-351C each provide three LAN
ports. LAN ports 1 and 2 are 100BASE-TX/1000BASE-T ports.
LANport 3 is an SFP port.
lThe DM-NVX-352C provides two LAN ports. LAN port 1 is a
100BASE-TX/1000BASE-T port. LAN port 2 is an SFP port.
lAn SFP port connects to a fiber-optic network using the
appropriate Crestron SFP-1G Series transceiver module (sold
separately). For information about installing a Crestron SFP-1G
transceiver module, refer to the SFP-1G Series Installation Guide
(Doc. 7979) at www.crestron.com/manuals.
lOnly one LAN port at a time can be used as the primary LAN
connection to a 1000BASE-T switch in order to stream network
video. Any other LAN port can then be used for connection to a local
network device or to another DM NVX device.
2
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

DM-NVX-350C and DM-NVX-351C Connections (DM-NVX-350C Shown)
3
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

DM-NVX-352 Connections
4
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

AUDIO I/O Connector Pin Assignments
The AUDIO I/O connector uses a 5-pin terminal block for balanced or
unbalanced analog audio input or output.
AUDIO I/O Connector
Balanced/Unbalanced Audio Input
Refer to the following table and diagrams for analog audio input pin
assignments and connection information.
Signal Name Balanced Audio Input Unbalanced Audio Input
+ L+ L+ In
− L− L− Signal return, jumper to GND
G Shield/ground Ground
+ R+ R+ In
− R− R− Signal return, jumper to GND
Balanced/Unbalanced Audio Output
Refer to the following table and diagrams for analog audio output pin
assignments and connection information.
Signal Name Balanced Audio Output Unbalanced Audio Output
+ L+ L+ Out
− L− Open
G Shield/ground Common ground
+ R+ R+ Out
− R− Open
5
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

LED Indicators
Refer to the following table for information about the LED indicators on
the card.
LED Indicator Color Meaning
TX Green The device is in transmitter
(encoder) mode
RX Green The device is in receiver
(decoder) mode.
OL Green The device is online with a
control system.
LAN 1 Green An Ethernet link is established.
Flashing
amber
Data activity is occurring on the
Ethernet link.
LAN 2 (DM-NVX-350C and
DM-NVX-351C only)
Green An Ethernet link is established.
Flashing
amber
Data activity is occurring on the
Ethernet link.
LAN 2 LINK (DM-NVX-352C
only)
Green An Ethernet link is established.
LAN 2 ACT (DM-NVX-352C
only)
Flashing
green
Data activity is occurring on the
Ethernet link.
LAN 3 LINK (DM-NVX-
350C and DM-NVX-351C
only)
Green An Ethernet link is established.
LAN 3 ACT (DM-NVX-350C
and DM-NVX-351C only)
Flashing
green
Data activity is occurring on the
Ethernet link.
HDMI OUTPUT Green An HDMI signal is being
transmitted at the HDMI
output.
HDMI INPUT 1-2 Green An HDMI signal is detected at
the corresponding HDMI input.
Upgrade the Firmware
Before using the device, upgrade the firmware. The latest firmware can be
downloaded from the DM-NVX-350C,DM-NVX-351C, or DM-NVX-352C
product page on the Crestron website (www.crestron.com).
Configure the Card
Configure the card using the web interface. To access the web interface,
open a web browser and then go to the IP address of the card.
NOTE: By default, the IP address of a card is assigned by a DHCP
server on the network. If a DHCP server does not exist on the network,
the IP address defaults to a link-local address in the 169.254. xxx . xxx
range (refer to RFC 3927 for detailed information about link-local
addressing).
To find the IP address of the card, use the menu on the front panel display
of the DMF-CI-8.
To log in to the web interface, enter the user name and password of the
card. The default user name and password are both admin .
6
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

Connect to the Cloud
The Crestron XiO Cloud™ service allows supported Crestron devices
across an enterprise to be managed and configured from one central and
secure location in the cloud. Supported devices are preconfigured to
connect to the service. Use of the service requires a registered Crestron
XiO Cloud account.
To connect the card to the Crestron XiO Cloud service:
1. Record the MAC address and serial number that are labeled on the
shipping box or printed circuit board (PCB). The MAC address and
serial number are required in order to add the card to the Crestron XiO
Cloud environment.
2. Do either of the following:
lIf you have a Crestron XiO Cloud account, go to
https://portal.crestron.io to access the Crestron XiO Cloud
service.
lIf you do not have a Crestron XiO Cloud account, go to
www.crestron.com/xiocloud to register for an account.
For detailed information about using the Crestron XiO Cloud service,
refer to the Crestron XiO Cloud Service User Guide (Doc. 8214) at
www.crestron.com/manuals.
Visit the Product Page
Scan the QR code to visit the product page.
DM-NVX-350C
www.crestron.com/model/6508252
DM-NVX-351C
www.crestron.com/model/6508250
DM-NVX-352C
www.crestron.com/model/6508635
7
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards

Additional Information
Original Instructions
The U.S. English version of this document is the original instructions.
All other languages are a translation of the original instructions.
Crestron product development software is licensed to Crestron dealers and Crestron
Service Providers (CSPs) under a limited nonexclusive, nontransferable Software
Development Tools License Agreement. Crestron product operating system software is
licensed to Crestron dealers, CSPs, and end-users under a separate End-User License
Agreement. Both of these Agreements can be found on the Crestron website at
www.crestron.com/legal/software_license_agreement.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cestron XiO Cloud, and DM NVX are either trademarks or
registered trademarks of Crestron Electronics, Inc. in the United States and/or other
countries. HDMI and the HDMI logo are either trademarks or registered trademarks of
HDMI Licensing LLC in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to
either the entities claiming the marks and names or their products. Crestron disclaims
any proprietary interest in the marks and names of others. Crestron is not responsible
for errors in typography or photography.
©2020 Crestron Electronics, Inc.
Doc. 8392B
03/24/20
8
DM-NVX-350C, DM-NVX-351C, and DM-NVX-352C QuickStart
DM NVX® 4K60 4:4:4 HDR Network AV Encoder/Decoder Cards