Crestron CSA-PWS10S-HUB User manual

CSA-PWS10S-HUB
Crestron Electronics, Inc. Installation Guide – DOC. 7438A
15 Volvo Drive Rockleigh, NJ 07647 (2037987)
Tel: 888.CRESTRON 12.13
Fax: [phone] Specifications subject to
www.crestron.com change without notice.
Introduction
The Crestron®CSA-PWS10S-HUB power supply powers up to 10 Crestron shades and features a built-in 5-segment
Cresnet®hub with network diagnostics capabilities. Local controls and indicators allow for easy testing of shades
without connecting to a control system.
The power supply is convection cooled for silent operation and can be surface mounted as a standalone device
(CSA-PWS10S-HUB). It is also available for order in an enclosure (CSA-PWS10S-HUB-CAEN-1X1), which can
be surface or flush wall mounted.
CSA-PWS10S-HUB Specifications
SPECIFICATION DETAILS
Load Rating
Total Shades Supported Provides power for up to (10) Crestron shades, each homerun to the power
supply
Output 24 Vdc
50 W per output LPS
350 W total continuous load
425 W for 2 minute on 2 minute off discontinuous shade load
Load Protection (10) Self resetting thermal fuses and (10) 4 A time lag fuses, Littelfuse JDYX2
0213 004 MXP (5 x 20 mm, 250 V, 4 A, time lag, cartridge) provided for each
50 W segment, (1) of each per output
Power Requirements 120—240 Vac, 50/60 Hz;
5 A maximum
Environmental
Installation Location Indoor use only
Temperature 32º to 104º F (0º to 40º C)
Humidity 10% to 90% RH (non-condensing)
Enclosure
CSA-PWS10S-HUB
CSA-PWS10S-HUB-
CAEN-1X1
Metal, gray, surface mount (indoor use only)
Includes CAEN-1X1, 16 gauge galvanized steel enclosure with vented gray steel
cover, surface mount or recessed in a wall (indoor use only)
Dimensions
CSA-PWS10S-HUB
Height
Width
Depth
CSA-PWS10S-HUB-
CAEN-1X1
Height
Width
Depth
7 9/16 in (194 mm)
12 15/16 in (330 mm)
2 11/16 in (68 mm)
16 9/16 in (421 mm)
16 1/8 in (409 mm)
4 7/16 in (113 mm)
Weight
CSA-PWS10S-HUB
CSA-PWS10S-HUB-
CAEN1x1
5.6 lb (2.6 kg)
15.0 lb (6.8 kg)
(Continued on the following page)

Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors
2•Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC. 7438A
CSA-PWS10S-HUB Specifications (Continued)
SPECIFICATION DETAILS
Input Terminal
(CSA-PWS10S-HUB-CAEN-
1X1 only)
18–10 AWG, 30 A, 600 V
Line Power
CSA-PWS10S-HUB
(1) Attached input power cable (~10 in long (254 mm)) with inline IEC 60320 C14
main power inlet;
Mates with removable power cord (included)
CSA-PWS10S-HUB-
CAEN-1X1
(1) Attached input power cable (~10 in long (254 mm)) with inline IEC 60320 C14
main power inlet;
Connects to ac power source using grounded pigtail cable and terminal block
(both included)
Cresnet (2) 4-pin 5 mm detachable terminal blocks;
Cresnet slave ports, paralleled;
Connect to Cresnet control network, power not supplied to these connections;
Cresnet power output ports with data pass-through;
In event of power failure the unit is auxiliary powered from this port to provide
status
A-E, 1-10 (10) 4-pin 5 mm detachable terminal blocks comprising (2) Cresnet ports per
each of (5) hub segments;
Each terminal bock provides 24 volts and 50 watts LPS
USB (1) USB Type B female, USB computer console port
LEDs
PWR 1-10
(10) Green LEDs, indicate 24 V present at each corresponding output;
Indicates over current situation
NET A-E (5) Amber LEDs, indicate Cresnet activity on each corresponding segment;
Indicates issues on the bus during diagnostic testing
NET HOST (1) Amber LED, indicates activity on the Cresnet bus
MSG (1) Red LED, indicates error messages and test mode
Push Buttons
MASTER UP
MASTER DOWN
TEST
RESET
(1) Push button, press and hold to raise all connected shades
(1) Push button, press and hold to lower all connected shades
(1) Push button, initiates diagnostic test
(1) Recessed push button, forces hardware reset

Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB
Installation Guide – DOC. 7438A Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB •3
Regulatory Compliance
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
As of the date of manufacture, the CSA-PWS10S-HUB and CSA-PWS10S-HUB-CAEN-1X1 have been
tested and found to comply with specifications for CE marking and standards per EMC and
Radiocommunications Compliance Labelling.
Federal Communications Commission (FCC) Compliance Statement
These devices comply with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) These devices may not cause harmful interference and (2) these devices must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors
4•Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC. 7438A
CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Top and Front Views)
1 1/4 in
(32 mm)
1 1/2 in
(39 mm)
5 11/16 in
(145 mm)
2 1/2 in
(64 mm)
1 5/16 in
(33 mm)
2 5/16 in
(58 mm)
(4x) Ø 1 3/4 in (45 mm)
Knockouts for 1 1/4 in
(32 mm) Conduit
2 9/16 in
(65 mm)
5/8 in
(16 mm)
15/16 in
(24 mm)
1 1/4 in
(32 mm)
1 1/4 in
(32 mm)
16 1/8 in
(409 mm)
16 9/16 in
(421 mm)

Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB
Installation Guide – DOC. 7438A Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB •5
CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Bottom View)
(21x) Ø 7/8 in (23 mm)
Knockouts for 1/2 in
(13 mm) Conduit
1 1/4 in
(32 mm) Typ.
5/8 in
(16 mm)
15/16 in
(24 mm)
2 1/2 in
(64 mm)
3 13/16 in
(97 mm)
11 1/4 in
(286 mm)
14 3/8 in
(365 mm)
1 1/4 in
(32 mm)
1 1/4 in
(32 mm)

Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors
6•Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC. 7438A
CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Side View)
1 in
(26 mm)
1 3/4 in
(45 mm)
(8x) Ø~3/16 in (5 mm) Mounting Holes
for #8 Wood Screws (Not Supplied)
2 1/2 in
(64 mm)
5 7/16 in
(138 mm)
1 7/16 in
(36 mm)
10 13/16 in
(275 mm)
15 13/16 in
(402 mm)
8 in
(203 mm)
2 1/4 in
(58 mm)
4 1/4 in
(108 mm)
4 7/16 in
(113 mm)

Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB
Installation Guide – DOC. 7438A Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB •7
CSA-PWS10S-HUB-CAEN-1X1 Overall Dimensions (Front View, Cover Removed)
2 1/4 in
(58 mm)
10 7/8 in
(276 mm)
10 15/16 in
(277 mm)
(4x) Ø 1 3/8 in
(35 mm)
Mounting Boss
Barcode Label for
Entire Assembly
Barcode Label for
Cabinet
(4x) 7/16 in
(12 mm)
(4x) Ø5/8 in
(16 mm)
(4x) Ø~5/16 in (8 mm) Mounting Holes
for #8 Wood Screws and #8 Large
Flat Washers (Not Supplied)
Cresnet connectors
are included.
Cable Tie
Anchors
2 3/4 in
(70 mm)
9 7/8 in
(251 mm)
I.T.E
POW ER SUPPLY
41JC
ASSEMBLED INCOO
CSA-PWS10S-HUB- CAEN-1 X 1
PN 6506320 SNXXXXX
000 00
INPUT: 120-240V~,50/60 Hz,5A MAX.
OUTP UT: 24V ,350WCONTIN UOUS,
425W 2MIN.ON 2MI N.OFF LI MITE D DUTY CYCLE.
50W MAX/OUTPUT LPS
I.T.E
POW ER SUPPLY
41JC
ASSEMBLED INCOO
CSA-PWS10S-HUB
INPUT: 120-240V~,50/60 Hz,5A MAX.
OUTP UT: 24V ,350WCONTIN UOUS,
425W 2MIN.ON 2MI N.OFF LI MITE D DUTY CYCLE.
50W MAX/OUTPUT LPS
REPLACEMENT FUSE F 1-F10:
5 X 20 MM 4A,250V~
TI ME LAG FUSE
PN 6506308 SNXXXXX
000 00

Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors
8•Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC. 7438A
CSA-PWS10S-HUB Overall Dimensions (Top, Front, and Bottom Views)
2 9/16 in
(66 mm)
1 1/8 in
(29 mm)
1 11/16 in
(44 mm)
2 11/16 in
(68 mm)
8 7/16 in
(215 mm)
10 11/16 in
(273 mm)
12 15/16 in
(330 mm)
9/16 in
(15 mm)
1/8 in
(4 mm)
1/4 in
(7 mm) Offset
(4x) Ø3/16 in
(5 mm) Mounting
Holes for #8 Pan
Head Wood
Screws
(Not Supplied)
Barcode Label
for Power Supply
All Cresnet
connectors and
fuses are included.
2 1/4 in
(58 mm)
IEC, 3
Conductor
Male Cable,
Aprox. 10”
(254 mm)
Long
12 3/8 in
(314 mm)
7 9/16 in
(194 mm)
6 in
(153 mm)
5/16 in
(9 mm)
12 3/8 in
(314 mm)
2 7/16 in
(63 mm)
3 1/16 in
(79 mm)
I.T.E
POW ER SUPPLY
41JC
ASSEMBLEDINCOO
CSA-PWS10S-HUB
INPUT: 120-240V~,50/60 Hz,5A MAX.
OUTP UT: 24V ,350WCONTI NU OUS,
425W 2MIN.ON 2MI N.OF F L IMIT ED DUTY CYCLE.
50W MAX/OUTPUT L PS
REPLACEMENT FUSE F1-F10:
5 X 20 MM 4A,250V~
TIME LAG FUSE
PN 6506308 SN XXXXX
000 00

Power Supply for Crestron Shade Motors Crestron CSA-PWS10S-HUB
Installation Guide – DOC. 7438A Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB •9
CSA-PWS10S-HUB Overall Dimensions (Side View)
Installation
The enclosure must be installed by a licensed electrician in accordance with all national and local codes.
CAUTION: Double pole/neutral fusing implemented.
CAUTION: The CSA-PWS10S-HUB-CAEN-1X1 houses equipment that needs to be air-cooled. Therefore, mount
in a well-ventilated area. The ambient temperature range should be 32°F to 104°F (0°C to 40°C). The relative
humidity should range from 10% to 90% (non-condensing). Allow adequate clearance in front of the vented cover
for servicing and ventilation.
NOTE: The CSA-PWS10S-HUB-CAEN-1X1 is designed for surface mounting or flush mounting on a wall.
NOTE: The CSA-PWS10S-HUB is intended for surface mounting on a wall.
NOTE: Enclosure and power supply are intended for indoor use only.
NOTE: When flush mounting, 5/8” drywall is preferred.
NOTE:Four keyholes are located within the enclosure and should be used if surface mounting.
Mounting the CSA-PWS10S-HUB-CAEN-1X1
For surface mounting, the enclosure must be mounted securely to building wall studs or at least 1/4 in (7 mm)
plywood using four #8 screws with four #8 large flat washers (not included) before operation. The enclosure cover
must be installed for normal use.
For flush mounting, the enclosure must be mounted securely to building wall studs using eight #8 screws (not
included) before operation. The enclosure cover must be installed for normal use.
Mounting the CSA-PWS10S-HUB
To surface mount the CSA-PWS10S-HUB, the power supply must be mounted securely to building wall studs or at
least 1/4 in (7 mm) plywood using four #8 pan head wood screws. Use the screw holes indicated in
“CSA-PWS10S-HUB Overall Dimensions” on page 8 to secure the power supply to the mounting surface.
7 7/16 in
(189 mm)
13/16 in
(21 mm)
5/8 in
(16 mm)
7 9/16 in
(194 mm)

Crestron CSA-PWS10S-HUB Power Supply for Crestron Shade Motors
10 •Power Supply for Crestron Shade Motors: CSA-PWS10S-HUB Installation Guide – DOC. 7438A
Wiring
Once the unit is properly secured to the mounting surface, the unit must be properly wired. Refer to the guidelines
below for details.
CAUTION: All power feeds must be protected by single pole listed circuit breaker or branch rated fuse no greater
than 20 A.
NOTE: Use copper conductors only—rated 75°C or better.
NOTE: All wiring must be installed in accordance with all local and national electrical codes.
NOTE: Four snap bushings are supplied. If required, insert into knockouts at the bottom of the enclosure to prevent
damage to low voltage wiring.
The device must be mounted before operation.
Class 1 and Class 2 field wires must be kept separate. Refer to the following illustrations showing wiring details.
Areas for high voltage (Class 1) wiring are along the left side of the unit. The right side of the enclosure is reserved
for low voltage (Class 2) wiring.
NOTE: The installer must provide disconnect means within site of the enclosure.
NOTE: The CSA-PWS10S-HUB power cable is considered to be a disconnect means. For this reason the total
length of power cable from CSA-PWS10S-HUB to the outlet cannot exceed 14 feet (4.5 meters).
Class 1 Wiring Details
Class 1 Wiring
WIRE CONNECTION COLOR
GND Ground Green/Yellow Stripe
NEUT Neutral White
LINE Hot Black
Class 2 Wiring Details
Neutral, Line,
and Ground
Connections
Class 1
Wiring Only
Power
From
120-240
Vac
Class 2
Wiring Only