Crestron FT2A-UTK-PWS User manual

FT2A-UTK-PWS
Power Supply for FT2 Series
Installation Guide
Description
The Crestron®FT2A-UTK-PWS is a 24 Vdc power supply that is used to supply power to
the power bus in an FT2-ELEC assembly. The FT2A-UTK-PWS can replace the power
supply that ships with the FT2-ELEC, or it can be used to supply additional power to the
FT2-ELEC if two FT2A-CHGR-USBA/C modules are installed as part of the
FlipTop™ system.
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.
Installation
Use the following procedure to install the FT2A-UTK-PWS.
NOTE: Connect the power supply to the power bus prior to installing any modules.
NOTE: Two power supplies are required if installing two FT2A-CHGR-USBA/C modules
in the FT2-ELEC. For more information, refer to the FT2A-CHGR-USBA/C Installation
Guide (Doc. 8219) at www.crestron.com/manuals.
1. Underneath the table, connect the power supply to the bottom of the power bus as
follows:
a. If connecting one power supply to the power bus, connect the dual connector
ends of the included Y-adapter cable to the two barrel jacks under the power bus.
Then, connect the power supply’s power cord to the single connector end of the
Y-adapter.
Y-Adapter Cable
Power supply
holder
FT2A-UTK-PWS
FT2-ELEC assembly
FT2A-UTK-PWS Mounting Locations
FT2A-UTK-PWS
mounting
locations (6)
NOTE: Ensure that the unit is properly grounded by connecting the chassis
ground lug to an earth ground (building steel).
2. Dress the power cord and secure it to the cable management bar on the bottom of
the assembly. Refer to the image above for the location of the cable management
bar.
5. Connect the included 5' 10" (1.78 m) power cable to the power jack on top of the
power supply, and then connect the other end to a power source.
NOTE: Do not apply power until all modules have been installed and all
connections have been made to the FT2-ELEC.
FT2-ELEC
power bus
barrel jacks
FT2 assembly
(bottom view)
Ground lug
Cable management bar
b. If connecting two power supplies to the power bus, connect each power supply’s
power cord to a barrel jack in the power bus.
Connecting the FT2A-UTK-PWS to the FT2-ELEC Power Bus
3. Slide the power supply into the power supply holder until it is secured in place.
4. Insert the power supply holder into the side of the FT2-ELEC assembly so that the
four mounting posts on the rear of the holder engage the four rectangular slots in
one of the six mounting locations. (Refer to the illustrations below.) Then, slide the
holder downward until it is secured to the assembly.
Attaching the FT2A-UTK-PWS to the FT2-ELEC Assembly

As of the date of manufacture, the product has been tested and found to comply with specications
for CE marking.
This product is Listed to applicable UL®Standards and requirements tested by Underwriters
Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specic patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specic information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks of Crestron
Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks
or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other
countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any
proprietary interest in the marks and names of others. Crestron is not responsible for errors in
typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.
Crestron Electronics, Inc. Installation Guide - DOC. 8251A
15 Volvo Drive, Rockleigh, NJ 07647 (2050263)
Tel: 888.CRESTRON 11.17
Fax: [phone] Specications subject to
www.crestron.com change without notice.