Crestron Dm-psu-8 User manual

DO GUIDE

DM-PSU-16 Rear Panel Connections

NOTE: Ensure that the device is properly grounded by connecting the chassis ground lug to an

earth ground (building steel).

NOTE: The eight POWER ports of the DM-PSU-8 and the sixteen POWER ports of the

DM-PSU-16 are PoDM and HDBaseT®PoE PSE (Power Sourcing Equipment) ports. Any wiring that is

connected to a PoDM or HDBaseT PoE port is for intrabuilding use only and should not be connected

to a line that runs outside of the building in which the PSE is located.

DM-PSU-8/DM-PSU-16

8-Port/16-Port PoDM Power Supply for DM 8G+®I/O Cards

DO Install the Device

The Crestron®DM-PSU-8 and DM-PSU-16 can be mounted into a rack or placed onto a at surface.

Mounting into a Rack

Each device occupies 1U of rack space. Using a #1 or #2 Phillips screwdriver, attach the two

included rack ears to the device. Then, mount the device into the rack using four mounting screws

(not included).

Placing onto a Flat Surface

When placing the device onto a at surface or stacking it with other equipment, attach the included

feet near the corners on the underside of the device.

DO Connect the Device

Connect the device as required for the application.

DM-PSU-8 Rear Panel Connections

DO Check the Box

QTY PRODUCT COLOR PART NUM.

2Bracket, Rack Ear, 1U 2032122

4 Foot, 0.5" x 0.5" x 0.23", Adhesive Black 2002389

1 Power Cord, 6' 7" (2 m) 4505164

POWER

MAX 15.4 W/PORT 1–8:

To POE IN port of DM 8G®I/O card

or to HDBaseT

device

100–240 V ~50/60 Hz

2.2–1.0 A:

Mains power input

Ground

POWER

MAX 15.4 W/PORT 1–16:

To POE IN port of DM 8G I/O card

or to HDBaseT device

100–240 V ~50/60 Hz

3.5–1.6 A:

Mains power input

Ground

DO GUIDE DOC. 7970A (2048244) 04.17

Specications subject to change without notice.

DO Learn More

Visit the website for additional information and the latest rmware

updates. To learn more about this product, use a QR reader

application on your mobile device to scan the QR image.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

These products are Listed to applicable UL®Standards and requirements by Underwriters Laboratories Inc.

Ces produits sont énumérés aux normes applicables et les exigences UL par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

Rack Mounting Safety Precautions

•Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be

given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specied by the

manufacturer.

•Reduced Airow: Installation of the equipment in a rack should be such that the amount of airow required for safe operation

of the equipment is not compromised.

•Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due

to uneven mechanical loading.

•Circuit Overloading: Consideration should be given to the connection of the equipment to the supply circuit and the

effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

•Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given

to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

The specic patents that cover Crestron products are listed at http://www.crestron.com/legal/patents. The product warranty can be found at www.crestron.com/warranty.

Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.

Crestron, the Crestron logo, DM 8G, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT is either

a trademark or registered trademark of the HDBaseT Alliance in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters

Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.