Crestron DigitalMedia 8G DM-RMC-100-S Dimensional drawing

DO GUIDE
DO Install the Device
The Crestron®DM-RMC-100-S can be mounted onto a at surface or onto a rack rail.
Mounting onto a Flat Surface
Using four mounting screws (not included), mount the device onto a at surface such as a wall or a
ceiling.
Mounting onto a Rack Rail
The DM-RMC-100-S mounts onto the front or rear rail of a rack. Position the device horizontally so
that the holes in one of the mounting anges align with the holes in the rack. Then, secure the device
to the rack using two rack mounting screws (not included).
DO Connect the Device
Connect the device as appropriate for the application.
Connections, Left Side
Connections, Right Side
DO Set the IP Address
Setup of the IP address of the DM-RMC-100-S depends on the way the device is congured within
the DigitalMedia 8G™ system:
• If the DM-RMC-100-S connects to a DM®switcher, the DM-RMC-100-S is congured by the
switcher automatically.
• If the DM-RMC-100-S connects to a DigitalMedia 8G ber transmitter, the
DM-RMC-100-S uses its own conguration settings. By default, DHCP (Dynamic Host
Conguration Protocol) is enabled. If assignment of the default IP address to the
DM-RMC-100-S is desired, hold down the SETUP button while the unit boots up.
The default IP address 192.168.1.244 overwrites the current setting. To manually set a different
IP address, use the Crestron Toolbox™ application.
DM-RMC-100-S
DigitalMedia 8G™ Fiber Receiver & Room Controller 100
DO Check the Box
QTY PRODUCT PART NUM.
1Connector, 4-Pin 2003576
1Connector, 5-Pin 2003577
1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045865
HDMI OUT:
To HDMI®
display
IR 1–2:
To IR
controllable
devices
LAN:
10BASE-T/
100BASE-TX
Ethernet to
local network device
COM:
To
RS-232
device
DM IN
MMF/SC:
From DM®switcher,
transmitter, or other
DM device
24 V
0.75A MAX:
From included
power pack
Ground

DO GUIDE DOC. 7816C (2044621) 05.17
Specications subject to change without notice.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn
more about this product, use a QR reader application on your mobile device to scan
the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
This product is Listed to applicable UL®Standards and requirements by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
The DM-RMC-100-S is a Class 1 laser product. It complies with safety regulations of IEC-60825-1,
FDA 21 CFR 1040 11, and FDA 21 CFR 1040 10.
WARNING: Visible and invisible laser radiation when open. Avoid direct exposure to beam.
NOTE: Plug the included dust cap into the optical transceiver when the ber optic cable is unplugged.
The specic patents that cover Crestron products are listed at patents.crestron.com. The product warranty can be found at www.crestron.com/warranty.
Certain Crestron products contain open source software. For specic information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. HDMI is either a trademark or registered trademark of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are either trademarks or
registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document
to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for
errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2017 Crestron Electronics, Inc.