CrimeStopper PlateCam SV-5200.IR User manual

INSTALLATION INSTRUCTIONS:
The SV-5200.IR and SV-5200.IR.C are bar-type license plate cameras with a super wide 180°
viewing angle and IR night vision. They are easy to install with no drilling required, requiring
minimal installation time. This uniquely designed product can be used for any passenger car,
SUV and Van. It can also be used on many large Semi Trucks, School Buses, and Transit
Buses
FEATURES:
•Revolutionary design integrates a Color rear vision camera with your rear license plate
•Enhance the look of your Car, SUV, Truck or Van.
•The 180°ultra wide-angle CMOS color camera provides rear images in real time and
eliminates the dangerous “blind-spot” directly behind your vehicle when backing.
•Works well in day or night, on most vehicles.
•Normal or Reverse Image (Selectable)
•The plate cam easily connects with other SecurView monitor or aftermarket monitor that
uses an RCA input
•Available in black and chrome color
•The PlateCam™ is designed for vehicles in which the license plate location is centered
and above the level of the rear bumper. The PlateCam™ may not perform well on
vehicles with low or offset license plate positions.
SV-5200.IR
SV-5200.IR.C
License Plate Bar-Type
Camera
with Night
Vision

INSTALLATION
MOUNTING:
1. The SV-5200.IR and SV-5200.IR.C Rear Vision Systems use a super wide-angle lens for best
all around performance. The Camera will display the full width of most parking spaces up to 8
feet or even wider.
2. These cameras are designed to work best on vehicles that have a license plate located at the
center and above the rear bumper. If your vehicle has a plate location that is offset to the left
side, right side, or your plate is located under the bumper then the PlateCam™ may not
provide optimum performance.
3. The SV-5200.IR and SV-5200.IR.C are designed to use the existing License Plate mounting
equipment
SIDE VIEW
License Plate
Camera Lens
Mounting
Surface
Cable
Factory License
Plate Bolt
NOTE
License Plate Should Not
Be Cut Or Trimmed
CAMERA:
1. The Camera has built-in circuitry to reverse the image so objects on the right of vehicle
appear on the right and objects on the left appear on the left when looking at a standard
monitor. (See Reverse Imaging next section for more information.)
2. The color CMOS camera is maintenance-free, waterproof (IP-68) and vibration resistant.
3. This camera has built-in Infra-Red LEDs for night vision. This will provide the driver with the
absolute best illumination when backing up the vehicle at night time.
4. The camera is completely electronic. There are NO manual adjustments for focus, etc.

REVERSE (MIRROR) IMAGING:
The SV-5200.IR and SV-5200.IR.C Cameras have built-in circuitry to “mirror” the image so objects on
the right of vehicle appear on the right and objects on the left appear on the left when looking at a
standard monitor. If your existing monitor or in-dash monitor has a reverse camera input where the
monitor itself performs the mirror image, then your picture will not be correct. If this happens, the SV-
5200.IR cameras have a jumper plug that can be connected to reverse the image back to normal.
(See Wiring Diagram)
WIRING:
1. Carefully choose a hidden out-of-sight location (possibly behind the plate) for drilling the cable
hole. Some vehicles may have an existing hidden rubber grommet or plug available to avoid
having to drill into the body. Be sure to double-check for any wiring or obstructions behind the
surface where you are going to drill the cable hole. Use the rubber grommet to make a watertight
seal for the cable where it passes into the vehicle.
2. Choose a convenient place to run the camera cable up the left, right or center of the vehicle. As
a rule of thumb, try to avoid main factory harness looms that may contain high levels or RF noise
or interference.
3. You can connect the camera power at the rear of the vehicle behind the reverse lights. You may
also connect power inside the vehicle under the dash or in the trunk. The Red power wire goes to
Reverse Light +12V, and the Black wire to Ground. The small white plastic plug is for reverse or
normal image switching. Leave the jumper disconnected for reverse image, connect the jumper
for normal image
4. Run the Yellow RCA video cable to the monitor’s video input or reverse camera input. Leave the
white RCA disconnected.
MONITOR
BLACK
RED
Connect to +12V
Reverse Light
Ground
Connect to RCA
Video Input of
Monitor YELLOW
SV-5200.IR CAMERA
BLACK
POWER PLUG WHITE
No Connection
NORM / REV
IMAGE PLUG
Connect Jumper for
Normal Image

TECH SUPPORT: [phone]
DISCLAIMER:
Under no circumstances shall the manufacturer or distributor of the PlateCam™ be held liable for
consequential or incidental damages sustained in connection with the use of the PlateCam™ Rear Vision
System. The PlateCam™ is designed as a safety enhancement device and is in no way intended as a
replacement for rear-view mirrors, side-view mirrors or physically checking the surroundings when
backing a vehicle. Always check surroundings for safety when backing! Objects on the monitor are
closer than they appear. For the best fit, modification of the vehicle license may or may not be
necessary. It is the sole responsibility of the vehicle owner to check and verify any and all State or
Federal Motor vehicle codes with regards to modifications of vehicle license plates. The manufacturer of
the PlateCam™ assumes no liability or responsibility whatsoever with regards modifications of the
license plate.
www.crimestopper.com
[e-mail]
Phone [phone]
FAX [phone]
© 2010 Crimestopper Security Products
7-15-2010
SPECIFICATIONS:
1/4 Inch Color CMOS Sensor Video Output: 1.0 V P-P composite (75 Ohm load)
Dimension (MM): 1"(L) × 7⅞"(W) × 1¼"(D) Supply Voltage: +12VDC
Weight:12 Oz. Power Consumption: 80mA
Pixels: 512 (H) x 492 (V) Electronic Shutter: 1/50 s – 1/100000s
Resolution: > 250,000 pixels White Balance: Automatic
More than 420 TV lines Gamma Correction: 0.45
Minimum Illumination: 0 LUX / F 1.2 S/N Ratio: More than 48dB
Lens Type: Wide Angle Operating Temp: -13 to 185 F (-20 to 75 C)
Horizontal Angle: 180° Gain Control: Automatic
Vertical Angle: 90° Digital Signal Processor w/10 Bit A/D Converter