CrimeStopper CS-2000 Manual

CS-2000
REMOTE CONTROL ALARM SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION
CONGRATULATIONS on your choice of a ™ Remote Alarm System by Crimestopper Security Products Inc.
This booklet contains the information necessary for installing, using, and maintaining your alarm system. If
any questions arise, contact your installation dealer first, or Crimestopper Security Products Inc. at the Tech
Support number below.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren,
L.E.D., Power, Ground, Doorpin, etc.
-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e.
Door Locks, Starter Kill, Hood, Trunk, and Auxiliary Remote Output etc.)
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
[phone]
www.crimestopper.com
[email protected]
This device complies with FCC Rules part 15. Operation is subject to the
following
two conditions: 1) This device may not cause interference, and (2) this device
must accept any interference that may be received, including interference that may
cause undesired operation. The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modification to this equipment. Such
modification could void the user's authority to operate the equipment.

INSTALLATION CAUTIONS & WARNINGS
BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR
BAGS, ABS BRAKES, AND BATTERY).
TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle.
MAKE CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.
DO NOT EXCEED MAXIMUM OUTPUT RATINGS! -SERIOUS DAMAGE MAY OCCUR. LIMITS FOR
ALARM FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD,
MEASURE LOAD WITH AN AMP-METER.
REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost.
DAMAGE MAY OCCUR TO SYSTEM IF PROPER PRECAUTIONS ARE NOT OBSERVED.
DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering
column, or any other moving parts in the vehicle.
COMPONENT MOUNTING
DO NOT Mount the control unit in the engine compartment.
DO NOT Mount the control unit or wiring harness where they can become entangled with moving parts
such as brake/gas/clutch pedals, or the steering column.
The alarm control module should be mounted in a concealed location. The Placement of the module will
affect the distance from which the remote transmitter can control the unit. The antenna wire should be routed
away from any metal if possible. Do not alter the length of the antenna wire or route it with other wires. Do
not ground the antenna wire.
SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing
downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body
metal near the siren.
LED: Mount the red LED in a visible location on the dashboard or console. Drill an 11/32" hole at the chosen location.
Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to
firewall or side paneling.
Override/Program Button: Mount the Override/Program push-button in a hidden location easily accessible to the
user in case the system must be disarmed without the use of the transmitter. This switch is also used to program
certain features.

WIRING
RED WIRE: +12V POWER INPUT (15 Amp fuse)
Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle
battery positive terminal.
WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT (10 Amp Max.)
Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the
parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or
2 diodes to separate the output signal.
BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.)
Connect to RED siren wire.
BLUE/WHITE WIRE: (-) NEG. DOOR LOCK OUTPUT
Connects to lock circuit of NEGATIVE door lock systems or to terminal 85 of a relay. See Door Lock diagrams.
WHITE/RED WIRE: (-) NEG. DOOR UNLOCK OUTPUT
Connects to unlock circuit of NEGATIVE door lock systems or to terminal 85 of a relay. See Door Lock diagrams.
ORANGE WIRE: (-) NEG. ARMED OUTPUT / STARTER DISABLE (500mA Neg.)
Ground output when system is armed. This output is used for disabling the starter or to activate other devices such as
scanner LED’s, window modules, voice modules etc. For starter kill, cut starter wire and connect between 87A and 30
on relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in the ON and CRANKING
position.
BROWN/WHITE WIRE: (-) HORN HONK OUTPUT (Optional, May Require Relay)
This wire provides a pulsed (-) negative output for honking the vehicle’s horn when the system is tripped or when panic
is activated. Connect this wire to Negative Horn trigger wire in the steering column or to a relay on vehicles with a
positive horn circuit.
BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION (Optional, May Require Relay)
Connect to terminal 85 of relay. Connect terminal 86 to constant. Connect terminal 87 to +12V constant or ground
depending on the type of dome light circuit in the vehicle. 30 to the dome light circuit.
BLUE WIRE: (-) HOOD/TRUNK INPUT
This wire is an input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches
that read ground when open. If no existing switches are available, install new pin switches. Note: DO NOT mount new
pin switches in water pathways.
GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, May Require Relay)
Connects to terminal 85 of a relay. Connect terminal 86 to constant. Connect terminal 87 to +12V constant or ground
depending on the type of circuit that needs to be activated. Connect terminal 30 to the device/circuit to be activated.

WIRING
YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS
Connect to an ignition wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and “Start”
positions.
BLACK WIRE: SYSTEM CHASSIS GROUND
THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from
the connection point to ensure a good connection. We recommend the kick panel area for your ground point.
VIOLET WIRE: (+) DOOR TRIGGER INPUT
Same as GREEN wire below except this wire is used for vehicles that show a positive voltage (12 volts) when the door
is open such as Ford.
GREEN WIRE: (-) DOOR TRIGGER INPUT
Identify the wire that reads Ground when any door is open and 12 volts when all doors are closed.
2 PIN PLUG (BLUE): PROGRAM/OVERRIDE PUSH BUTTON
p
2 PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT)
4 PIN SENSOR PLUG:
WHITE WIRE: NEG. WARN AWAY *The Sensor supplied with the system does not require
BLUE WIRE: NEG. TRIGGER any additional wiring, simply mount the sensor in a
BLACK WIRE: SENSOR GROUND suitable location, plug in, and adjust sensitivity.
RED WIRE: SENSOR +12V POWER
PROGRAMMING
PROGRAMMABLE OPTIONS
1. Turn the Ignition ON and press the Override/Program button 5 times. You should hear a long confirmation chirp.
2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to
the feature list below. The siren will chirp for each button press.
3. When you get to the desired option number, press button the appropriate button on the transmitter change the
option according to the chart below. Button #1 gives a single light flash/siren chirp and Button #2 gives two light
flashes/siren chirps. See chart Below for Option descriptions and vales.
4. Change ONE option at a time repeating steps 1-3 as needed. When you are finished customizing options, check
operation to see if the option(s) have changed.
Option #
Description Button #1 (Large) Button #2 (Small)
1Passive Arming OFF (Default) ON
2Autolock with Ignition ON (Default) OFF

PROGRAMMING
SILENT ARMING /DISARMING
The system can be silently armed and disarmed as normal with but with no siren chirp. Turn ignition on and press the
#2 (Small) Button for about (3) seconds. You will hear (2) siren chirps. After the ignition is turned off, there will be no
siren chirps on arm/disarm. Repeat this procedure to enable chirps. (There will be 4 chirps when re-enabling)
ACTIVE RE-ARM PROGRAMMING
To enable this feature, Turn ignition on and press the #1 (Large) Button on the for about (3) seconds. (2) Siren chirps
will be heard when disabling this feature. Repeat procedure to enable. (1 siren chirp when enabling)
TRANSMITTER PROGRAMMING Note: System can learn up to 3 different codes max.
1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (1)
short chirp.
2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button.
The system is now in programming mode.
3. Press Button #1 on new transmitter –siren will chirp to confirm programming. Repeat Step 3 within 5 sec. for up to
2 additional transmitters.
4. Turn off Ignition.
Note 1: If only one transmitter is being programmed, continue pressing button #1 until dash LED flashes goes out and
the system chirps to exit programming mode to prevent unauthorized codes and noise from entering the system.
Note 2: Programming mode is exited automatically after 5 seconds of last code transmission or once 3 new codes
have been programmed. The LED will flash (4) times indicating program mode exit.
OPERATION
ACTIVE ARMING
To arm the system, press the #1 (Large) button on the transmitter. You will hear a single siren chirp and the lights will
flash once. Doors will lock and the starter will be disabled if these optional features are installed. The red LED in the
vehicle will start flashing after 15 seconds. After a short delay to allow vehicle and electronics to stabilize the system
will be completely armed. If there is an intrusion into the vehicle or hard impact to the body the alarm will sound and
flash the lights for 45 seconds. After 45 seconds the system will automatically shut off and re-arm to continue to
protect the vehicle. If a door is left open the unit will cycle a second time and continue to protect the other non-
tampered zones. Note: To Arm/Disarm with a Soft (NIGHT) chirp press and release the #2 (Small) button.
DISARMING
To disarm the alarm and unlock the doors, press the #1 (Large) button on the transmitter. You will hear 2 siren chirps
and the lights will flash twice. Dash LED stops flashing.

OPERATION
REMOTE PANIC PROTECTION
To sound the alarm upon command (panic), press and hold the #1 (Large) Button for at least (2) seconds until the
siren sounds. Press the same button again to reset panic mode.
TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL)
To pop the trunk (if optional feature is installed), press the #2 (Small) Button for at least 1 second.
EMERGENCY OVERRIDE/ VALET MODE
If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to perform an
Emergency Disarm. Open the door with the key, which will activate the alarm, turn the ignition ON, and press the
override/program button about 3-4 seconds. The Alarm will disarm and go into Valet mode. (LED on solid). Repeat
the above procedure to Exit/Enter Valet mode. NOTE: Keyless Entry features will still operate when in Valet Mode.
ACTIVE CARJACK
This feature provides Active (user controlled) Carjack protection. When the Ignition is on (vehicle is running),
press buttons #1 and #2 together for 1 second to activate a Carjack countdown. (Parking lights will turn on for
3 seconds as confirmation) 30 seconds later, the unit will begin a Carjack Cycle consisting of 15 sec. of pre-
warning chirps turning into a full activation with siren/flashing lights for up to 5 min. To reset Carjack, press
Buttons #1 and #2 together or turn Ignition OFF, then ON and hold the override/program button for 3 seconds.
PASSIVE ARMING MODE (Programmable)
Passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed.
The LED will begin flashing rapidly while counting down. If a door is open, the system will wait (LED solid) for the door
or zone to close before arming. Note: This unit does not include a Passive Door Lock feature.
PRIOR INTRUSION ALERT
If the system was tripped in your absence, the dash LED will be flashing rapidly and when the system is disarmed it will
chirp/flash 3 times. Inspect your vehicle to check for any damage or if a theft has occurred.
DOME LIGHT ILLUMINATION (OPTIONAL)
This feature turns on the vehicle’s dome light upon disarm for 30 seconds or until the key is turned on.
DEFECTIVE ZONE ALERT/BYPASS
If a door/zone is left open after arming, the siren will warn you with 4 chirp/flashes and bypass the zone automatically.
AUTOLOCK/UNLOCK WITH IGNITION (Programmable)
This feature will allow the unit to automatically lock when the ignition is turned on and unlock when turned off.
ACTIVE RE-ARMING, [ACCIDENTAL DISARM PROTECTION] (Programmable)
Active Re-arming allows the system to re-arm itself 30 seconds after being disarmed with the remote if a door has NOT
been opened. This is handy if the vehicle is accidentally disarmed without your knowledge.

POWER DOOR LOCK WIRING
++
+

87A
86
87
30
85
87A
86
30
BATTERY
+-
IGN
EMERGENCY
DISARM/
VALET/
PROGRAM
SWITCH
PIN SWITCH
(+)POSITIVE DOOR
SW
HOOD/TRUNK
(-)NEGATIVE
RELAY
PIN SWITCH
OPTIONAL
STARTER KILL
PIN SWITCH
(-)NEGATIVE DOOR
LED
FUSE
BOX
+
IGNITION
"ON & START"
START WIRE
(-)DOOR TRIGGER
YELLOW
CUT
(-) AUX. REMOTE OUTPUT
GRAY
(-)HOOD/TRUNK TRIGGER
BLUE
+ DOOR TRIGGER
WHITE/RED
NEG. ARMED OUTPUT
ORANGE
(STARTER DISABLE)
STARTER
+IGN SWITCHED "ON"
CHASSIS GROUND
RED FUSE
10 A
BROWN
+ 10A MAX
WHITE
BLACK(GROUND)
WHITE(WARNING)
RED (+)
BLUE (TRIGGER)
PARKING
LIGHTS
(-) NEG. LOCK OUTPUT
DUAL-STAGE
SHOCK SENSOR
SIREN
BLUE/WHITE
(-) NEG. UNLOCK OUTPUT
85
87A
86
87
30
85
BLACK/WHITE
(-)DOME ILLUMINATION
BLACK
VIOLET
GREEN
RELAY
OPTIONAL
RELAY
OPTIONAL
BROWN/WHITE
(-) HORN HONK OUTPUT
CS-2000
+ SIREN OUTPUT
RED
BLUE