CrimeStopper CoolStart RS-1604TW1 User manual

RS-1604TW1/RS-1704TW2/RS-1804FM
RS1905FM
2-Way Paging Remote Engine Starting & Keyless
Entry System with 1-Way Sidekick Remote Control
OPERATING INSTRUCTIONS
-PRIMARY: Thesearefeaturesthatmustbeconnectedinorderforthesystemtooperateproperlyi.e.Remote
Startconnections,Flashinglights,BrakeReset. Forprogramming,thehoodpinandprogrambuttonarerequired.
-OPTIONAL: These are features are to be connected only if desired or agreed upon by the customer and the
installingdealeri.e.DoorLocks,TrunkPop,DomeLightIllumination,Horn-Honk, Anti-Grind,etc. Thesefeatures
may also require additional parts and/or labor fees. Consult with your installer beforehand to be sure of what is
going to be installed with your particular system.
TECHNICALSUPPORT:[phone]
Monday -Friday8:00am -4:30pmPacificStd.Time
WebSite:www.crimestopper.com
E-mail:[email protected]
CRIMESTOPPERSECURITYPRODUCTS,INC.
1770S.TAPOSTREET,SIMIVALLEY,CA.93063
REV C–09.30.2005
This device complies with FCC Rules part 15. Operation is
subject to the following two conditions: 1) This device may not
cause interference, and (2) this device must accept any
interference that may
be received, including interference that
may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by
unauthorized modification to this equipment. Such modification
could void the user's authority to operate the equipment.

2
TABLE OF CONTENTS
OperationCautions&Warnings….………………..….…………………………………….…………………...………2
2-WayPagingLEDRemote TW1.........…………………………………………………………….…………..……….3
2-WayPagingLCDRemoteTW2..……………………………………………………………………………...……….4
2-WayPagingLCDRemoteFM…..……..……………………………………………………………………...…...…..5
Usingthe Remote 1-WayRemote………………………………………………………………………………….….6-7
RemoteEngineStarting…………………………………………………………………………………………...…..8-11
TurboTimerMode……………………………….……………………………………...………………………….….…12
ConvenienceandSafetyFeatures…….……………………….………………..………………………..….....….13-14
TransmitterProgramming….…………….………………………………………….……………….…..…….…......…15
2Vehicle Operation.………………………………….………………...……………………..………...……..…...……16
Troubleshooting“BeforeYouCall”………….…………..………………………………………….………….…...17-18
LowBatteryWarningandreplacingthe AAA batteryonLCDRemote…………………………………………….19
SettingtheClock…………………………………………………………………………………...………...…BackPage
OPERATION CAUTIONS & WARNINGS
CRIMESTOPPERSECURITYPRODUCTS,INC.andits VENDORSshallnotbeliableforanyaccidentresulting
fromtheuseofthisequipment.Thissystemisdesignedtobeprofessionallyinstalledintoacarorvehicleinwhich
allitems,suchasparkingbrakeandallassociatedcomponents,doorswitches,transmissionshiftlinkage,throttle
linkage,andallenginesafetyfeatures,areinperfectworkingcondition.
DO NOTinstallthe Remote EngineStartingSystemonMANUAL TRANSMISSION vehicles. If accidentally left
ingearthevehiclecouldbecomeaself-propelledthreatto lifeandproperty.
ITISABSOLUTELYTHEOWNER’SSOLERESPONSIBILITYTO:A)Understandtheoperationofthissystem
anditssafetyfeatures.B)Checkforproperoperationofthesystempriortoacceptingdeliveryofthevehiclefrom
theinstallationfacility. C) Check andmaintaintheconditionofthevehicleandall itemsrelativetotheproper
operationofthissystemanditssafetyfeatures. D)Alwaysleavethedoorsandwindowsclosedandlockedto
protectagainstaccidentandtheft.
DO NOT remote startthevehiclein a closed garage. Make sure that the garage door is open or there is
adequateventilation.Failuretoobservethisrulecouldresultininjury or death from poisonous Carbon Monoxide
fumes.

3
2-WAY PAGING LED REMOTE RS-1604TW1
TWO-WAYPAGEROPERATION&PAGETONES:
FEATURE BUTTON ACTION BEEPS LED/FLASH
LOCK #1(Lock) Press&Release 1X then 1X again Orange/ 1X
UNLOCK #2(Unlock)
Press&Release 1X then 2X again Green/ 2X
AUX#1 #3 (Trunk) Press &Hold 2Sec. 1Xthen 3X again Yellow / 1X
REMOTESTART #4 (Start) Press& Hold 2Sec. 1Xthen 3X again Blue /3X
ENGINERUNNING 6XBlue /6X
TURNOFF ENGINE
#4 (Start) Press& Hold2Sec. 1XNo Page back
PANIC #1(Lock) Press& Hold3Sec. 1X then 2X/12X Orange12X/Green1X
UNLOCKLOCK
PAGING
LED's
REMOTE
ANTENNA
FIXED
TRUNK
#1 #2
#3 #4
POP START
#5
CAR2
nd
OPERATION:
BUTTON 1 (Lock Symbol):
•Press and release to Lock doors.
•Press and Hold for more than 3 seconds to activate
“Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Unlock doors.
BUTTON 3 (Trunk Symbol):
•Press andHold for two seconds to activate trunk pop
(Optional Feature).
BUTTON 4 (Start):
•Press and Hold for two seconds to Start/StopEngine
BUTTON 5 (Side button)
§Press and Release to show the previous status.
§Press and Hold for 5 second to switch to vehicle #2.

4
#2 UNLOCK
LCD
SCREEN
#4 ENGINE
START/STOP
#1 LOCK
#3 TRUNK
#5 RECALL
CAR I or II
FIXED
ANTENNA
AM
OPERATION:
BUTTON 1 (LOCK Symbol):
•Press and release to Lock doors.
•Press and Hold for more than 3 seconds to activate “Panic”
feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Unlock doors.
BUTTON 3 (Trunk Symbol):
•Press and Hold two seconds to activate trunk pop (Op
tional
Feature).
BUTTON 4 (Start Key Symbol):
•Press and Hold two seconds to Start/Stop engine.
BUTTON5 (On side of remote):
•Press and release to light up the LCD screen.
•
Press and release twice to recall the last message from the
LCD screen.
•Press and Hol
d two seconds to change from Car 1 to Car 2
•Press 5 times to change the time and
enable/disable beep
tones from the remote.
LOCK
UNLOCK
TRUNKPOP
REMOTE
START
LOWBATTERY
PANIC
2-WAY PAGING LCD REMOTE RS-1704TW2

5
2-WAY PAGING LCD REMOTE RS-1804FM/1905FM
#1 ARM/
LOCK #4 ENGINE
START/STOP
#5
RECALL /
CAR I OR II
#3 TRUNK
POP
#2 DISARM/
UNLOCK
ANTENNA
START
FIXED
LCD
SCREEN
PM
PM
PM PM
PM
IGN
PM
IGN
(<<<< MOVING <<<<<)
LOCK UnLock Trunk Pop ConfirmRemote SuccessfulStart
StartRequest
OPERATION:
BUTTON 1 (Lock Symbol):
•Press and release to Lock system.
Press and Hold for more than 3 seconds to activate
“Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Unlock system.
BUTTON 3 (Trunk Symbol):
•Press and Release to activate trunk pop (Optional
Feature).
BUTTON 4 (Start Symbol):
•Press and release to Start/Stop Engine.
BUTTON 5 (On Side of Remote)
•Press and release to recall the last
message from the
LCD screen.
•Press and Hold 5 seconds to change from Car 1 to Car 2.
•Press 5 times to enable/disable beep tones from the
remote.

6
USING THE 1-WAY REMOTE
The transmitter supplied with the CoolStart system contains four buttons, flashlight, and vehicle 2 switch. The
button configuration of the CoolStart system is Factory-set and unchangeable. See Page 16for additional
information on how to use your remote to operate a secondvehicle equippedwith a CoolStartsystem.
NOTE:BUTTON#4 and#3 RemoteStart/Trunk
There is a deliberate delay or 2 presses (Optional) built into the system on button #4 and #3 to help prevent
accidentalremotestartingfromtheremotebeinginyourpocketorpurse. Duringnormaluse,ifyoupressbutton
#4 or #3 too quickly, the system may not start the engine or open trunk.
OPERATION:
BUTTON 1 (Lock Symbol):
•Press and release to Lock doors.
•Press and Hold for more than 3 seconds to
activate “Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Unlock doors.
BUTTON 3 (Trunk Symbol):
•Press andHold for two seconds to activate
trunk pop (Optional Feature).
BUTTON 4 (Start):
•Press and Hold for two seconds to Start/Stop
Engine
BUTTON 5 (Side button)
§Press and Release to show the previous
status.
§Press and Hold for 5 second to switch to
vehicle #2.
COOLSTART
#3
#1
#2
#4
LOCK
TRUNK
REMOTE
UNLOCK
VEHICLE 2
FLASHLIGHT
START
#5
Replacement Battery
GP23A
(12volt)

7
USING THE 1-WAY REMOTE RS-1905FM
START
LOCK
UNLOCK
REMOTE
#4
#3
#2
#1
2NDVEHICLE
TRUNK
(AUX#3)
(AUX#2)
(AUX#4)
STARTER #5
COOL START
The transmitter supplied with the RS-1804FM/1905FM systemhas five buttons. The button configuration of the
RS-1804FM/1905FMisFactory-setandunchangeable. See Page 16for additional information on how to use your
remotetooperatea secondvehicleequippedwitha CoolStartsystem.
NOTE:BUTTON#4 and#3 RemoteStart/Trunk
There is a deliberate delay or 2 presses (Optional) built into the system on button #4 and #3 to help prevent
accidentalremotestartingfromtheremotebeinginyourpocketorpurse. Duringnormaluse,ifyoupressbutton
#4 or #3 too quickly, the system may not start the engine or open trunk.
Replacement Battery
GP23A (12volt)
OPERATION:
BUTTON 1 (Lock Symbol):
•Press and release to Lock doors.
•Press and Hold for more than 3 seconds to activate
“Panic” feature.
BUTTON 2 (Unlock Symbol):
•Press and release to Unlock doors.
•Press 2 times for Driver Door Priority Unlock.
BUTTON 3 (Trunk Symbol):
•Press andHold for ½ second or press twice to
activate trunk pop.
BUTTON 4 (Start):
•Press and Hold for ½ second or press twice to
Start/Stop Engine.
BUTTON 5 (Vehicle #2/ AUX#2/AUX#3/AUX#4)
§AUX #2: Press button 5 then press button 1.
§AUX #3: Press button 5 then press button 2.
§AUX #4: Press button 5 then press button 3.
§vehicle #2.
§Press and Hold for 2 sec. for vehicle #2.

8
REMOTE ENGINE STARTING
REMOTEENGINESTARTING -SUCCESSFULSTART:
1) Press the remote start button for at least 1/2 second (Default) ortwice ifsetfordoublepress.
2) Parking lights flash once; return solid,and the Ignition/Acc circuits turn on.
3) After a few seconds the Starter Motor engages, Parking lights and Acc circuits will turn off while cranking.
4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock.
5) Enginewill remain runningforprogrammedruntimeuntilresetwithBrakepedal. Ifneeded,theenginecanbe
turnedoff with remotetransmitter by pressingand releasing ordoublepress the Start button.
AFTER
IGN
4
STARTER
THEN
FLASH 1X
SOLID
SOLID
SEC.
THE REMOTE STARTER BUTTON IS PROGRAMMABLE FOR 1 OR 2 PRESSES
REMOTEENGINESTARTING -UNSUCCESSFULSTART
Intheeventthattheenginedoesnotstartonthefirstattempt,thesystemshutsdownforafewseconds,and then
attemptstorestarttheenginea2nd and3 rd time. For hardstartingengines,theunitwillallowastartercrank time of
up to 10 secondsmaximum. This should provide ample cranking time for difficult starts, but is limited to 13
seconds to help prevent damage to the starter from over cranking.
1) Ifengine starts on2nd or 3rd attempt,seesteps4&5aboveof"SuccessfulStart".
2) IfThird attempt fails to start engine, the system will turn off and doors will remain locked.
NOFURTHERATTEMPTSWILLBEMADEAUTOMATICALLY
TURNINGOFFAREMOTESTARTEDENGINE:
1) Engine is running in Remote Start (Parking lights ON).
2) Pressand release theremote start button.
3) Engine& parking lightsOFF, Doors re-lock/re-arm.

9
REMOTE ENGINE STARTING Cont.
ENTERINGYOURREMOTESTARTEDVEHICLE:
1) Withengine running, RemoteUnlock system (Ifequipped) or opendoor with key.
2) Enter vehicle and be careful not to step on brakepedal! (RemoteStartReset).
3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.
4) Remotestarter will resetinstantly when thebrake is pressed. Parkinglights will turnoff and theignition key is
nowcontrolling your vehicle.
REMOTESTART RUNTIMERESET:
You can now reset the engine-run timer to allow for more running time after remote start has already occurred
usingthe remote control. Afterasuccessfulremotestart, pressboththeLock& Unlock buttons together for at
least 2 seconds. The parking lights will flash 3 times and internal enginetimerwill resetback to zero minutes.
IDLEDOWNMODE:
This mode allows the unit to take over operation of the parked vehicle while the ignition key is removedandyou
exitthevehicle. Thevehicleisputintoaremoterunningconditionbeforeyouexitanditwillremainrunningforthe
programmed run time or until you come back.
Examples:
•You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the vehicle,
(with keys in hand) remote lock doors or arm alarm. When you return, unlock, turn ignition ON and drive away.

10
REMOTE ENGINE STARTING
IDLEDOWNMODE -EXITINGTHEVEHICLE:
1) Withvehicleenginerunningwithkey, **presstheRemoteStartbuttonforatleasta1/2 second ortwiceifsetfor
doublepress.
2) Parking Lights will turn ON.
3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released.
4) TurnOFF Ignition and remove key. Engine should remain running.
5) Exitvehicle,thenremotelockdoorsifdesired.
6) Engine will remain running for programmed run time or until you return (whichever comes first).
IGN
SOLID
OFF
UNLOCK
ENTERINGAVEHICLEDURING “IDLE-DOWN”or“INFINITYRUN”MODES:
1. With engine running in "IDLE DOWN" (parking lights ON), unlock door via remote or key.
2. Entervehicle and becareful not tostep on brakepedal! (Remote StartReset)
3. TurnIgnitiontoON/RUNposition,thendepressbrakepedaltoresettheRemote Starter.Parkinglightswill
turnoff indicating the Remote Start is OFF and Vehicle is running by the Key. Drive away as normal
INFINITYRUNMODE
Thismodecanonlybeactivated when"IdleDown" procedure. The Infinity Runmodeallowsthevehicleengineto
remain running INDEFINITELYaftertheprogrammedruntimeelapses. Thismodewillallowthevehicletobeleft
running and unattendedwithout theignitionkeyintheswitchpreventingthevehiclefrombeingstolen. Thismode
canbebeneficialtolawenforcementorcommercialtrucksthatneedtoremainrunningunattendedforlongperiods
oftime. See nextpageforInfinitymodesteps.
**Programmablefor½secondpressordoublepress.Thisoptionisselectablebyyourinstaller.