Crosley Furniture CO1001A User manual

C R O S L E Y
F U R N I T U R E
METAL CHAIR
CO1001A

C R O S L E Y
F U R N I T U R E
Congratulations! You have purchased a stylish piece of Crosley Furniture. We strive
to provide fine furniture products, built with quality materials. Please carefully follow
the assembly instructions to ensure your furniture is assembled correctly to provide
long lasting enjoyment.
Should you experience any missing or damaged parts, do not return to the store.
Please contact us directly at 800-815-4796.
Care: Use a soft clean cloth that will not scratch the surface when dusting. Use of
furniture polish is not necessary. Should you choose to use polishes, test in an
inconspicuous area first. Use of solvents of any kind may damage your furniture's
finish. To clean, simply use a soft clean cloth moistened with lukewarm water, then
buff with a dry soft clean cloth.
1 of 5

2 of 5
PART LIST
A B C D E
1PC1PC 1PC 1PC 1PC 1PC
HARDWARE LIST
12345
Long Allen Bolt 1/4" NUT
HEX WRENCH
BOLT COVER
ALLEN KEY
Short Allen Bolt
NUT COVER
FOOT CAP
FACTORY ASSEMBLY
E6.5 X 1.0 MM
WASHER
6 7 8 9 10
4 PCS 4 PCS 4 PCS 8 PCS 8 PCS
8 PCS 1 PC 1 PC 2 PCS
FOOT CAP
FACTORY ASSEMBLY
2 PCS
Chair Back Chair Seat
Left leg
Right Leg
Leg Connector

3 of 5
Step 1: Place the chair seat (B) on a solid flat surface. Position the chair back (A) as
shown in (Figure 1) so that the holes in the chair back align with the holes in
the chair seat. Insert Short Allen Bolt (1) through the holes of the chair back
(A) and then through the holes in the chair seat. Add a 1/4" nut (4) to the end
of each bolt. Tighten using hex wrench (7) and Allen Key driver (8). Do not over
tighten. Cover nuts and bolts with covers (5 & 6). Repeat for remaining three
holes on each back(A).
C
Figure 1
A
B1
5
4
6
Step 2:
will need to be removed for assembly and can be discarded.
Protective caps were used on the ends of Legs (C & D) for shipping. These
Figure 2
Figure 1
8
7

4 of 5
Step 4:Insert the end of Leg Connector (E) into Legs (C & D). Attach Leg (D) to Chair
Back (A) using Long Allen Bolt (2), Washer (3), 1/4" Nut (4) & Nut Cover (6) as
shown. Note - The chair is designed for the Leg Connector (E) to be held in place
with tension. You will need to turn the chair on it's side and press Leg (D) down
to meet Chair Seat (B). Turn the chair on it's side with Leg (C) on a flat
non-abrasive surface. Press Leg (D) down to meet Chair Seat (B) and attach
using the same method as in Step #3. Turn the chair upright on it's base & it is
ready for use.
If the chair is not square or sitting properly, slightly loosen the bolts, square
up the chair, and re-tighten.
Step 3:
the holes in the chair leg assembly. While one person holds the chair seat/chair
back assembly as shown in (Figure 3), have another person attach to the chair
leg assembly. Add a E 6.5 x 1.0mm washer (3) to Long Allen Bolt (2) and insert
through aligned holes in the rear arm and chair back.
The holes in the chair seat/chair back assembly must be perfectly aligned with
Figure 3
5
2
3
8
4
6
7
5
2
3
8
4
6
7
Figure 4
5
2
3
5
2
3
4
4
6
6
C
D
E
8
8
4
6
7
7
7