Crowcon APM 155 User manual

APM 155
PRESSURE
METER
OPERATING
INSTRUCTIONS
Crowcon Detection Instruments
172 Brook Drive,
Milton Park,
Abingdon,
Oxfordshire OX14 4SD
Tel: [phone]
email: [e-mail]
web: www.antonbycrowcon.com
INSTRUMENT OPERATION
ON / OFF
Press and hold button for 0.5s to turn on.
Press and hold button for 2s to turn off.
Default switch-off interval is 5 minutes, unless any
button is activated or the pressure level is above 1
mbar or a timed test is active.
MENU STRUCTURE
Main Menu
Test Menu
Let-by / Tightness
Pressure Test
Strength Test
Units of Measurement
Settings
Auto off timeout
Back light
Key click
Report
Supervisor settings
Set date & time
Edit owner line 1
Edit owner line 2
Change Password
Stored Logs
Select a log
Find a log by number
Delete all logs
Test Menu –Let-by / Tightness
Used to carry out let-by, stabilisation and tightness
test.
Durations, pass & fail controlled by user
Test can be set to monitor lapsed time or the user can
set a countdown timer which alerts user when the
timer expires.
2-stage exit of test so that an accidental press of the
Escape button prevents the automatic termination of
the test.
Data can be stored & shared.
1. Positive pressure input spigot
2. Negative pressure input spigot
3. Backlit LCD screen
4. Multi-function 1 button
5. Multi-function 2 button
6. Multi-function 3 button
7. Power / Enter button
8. Escape / Cancel button
9. Infra-red LED
10. Magnet
11. Tilt stand / hook
STANDARD ACCESSORIES
The APM 155 is supplied complete with:
•Three AA Alkaline batteries
•Operating instructions
•Protective rubber boot with stand, hook
and magnet
INSTRUMENT APPLICATION
This instrument is not suitable for use with corrosive
substances or cyclic hydrocarbons, e.g. motor oil,
transmission fluid and Freon. To use the APM 155
with these components, isolation must be provided in
the form of a buffer, such as a mineral oil or dry air.

Test Menu –Pressure Test
Used for timed pressure tests.
Durations, pass & fail controlled by user
Test can be set to monitor lapsed time or the user can
set a countdown timer which alerts user when the
timer expires.
2-stage exit of test so that an accidental press of the
Escape button prevents the automatic termination of
the test.
Data can be stored & shared.
Test Menu –Strength Test
Used for timed strength tests.
Durations, pass & fail controlled by user
Test can be set to monitor lapsed time or the user can
set a countdown timer which alerts user when the
timer expires.
2-stage exit of test so that an accidental press of the
Escape button prevents the automatic termination of
the test.
Data can be stored & shared.
Units of Measurement
Select this menu option to change the pressure units
displayed on the meter.
Settings Menu –Auto off timeout
Changes the period when the unit will switch off if
inactive.
Settings Menu –Backlight
Changes the brightness of the backlight.
Lower settings will prolong battery life.
Settings Menu –Key Click
Enable/disable button click.
Settings Menu –Report
Change report sending option (printer, wireless or
toggle).
Settings Menu –Supervisor Settings
User configurable settings. Allows setting of time and
date, owner/company name and user password.
Stored Logs Menu
Search and retrieve stored logs. Allows log to be
reviewed, re-printed or re-transmitted over the
wireless link.
BATTERY REPLACEMENT
1. Remove the protective rubber boot by slipping it
away from the bottom of the case and sliding it over
the pressure spigots exposing the case back.
2. Remove the battery cover from the bottom of the
case by removing the four screws.
3. Remove the three AA batteries and replace with
good quality AA Alkaline batteries taking care to
install them the right way round.
4. Replace the battery cover carefully making sure it is
alligned properly and replace the screws. Take care
not to over tighten the screws otherwise it may
damage the case.
For best results and longer life always use quality
alkaline batteries MN1500 or equivalent.
CAUTIONS
Exposure to silicone based products, corrosive gases,
water / condensation and freezing should be avoided
at all times as this will cause damage to the sensor
and internal component corrosion.
This instrument should not be stored or operated
outside of its operating temperature range.
Particular care must be taken not to exceed the
maximum pressure ratings for the device as this
may rupture the sensor membrane. This is not
covered by the manufacturer’s warranty.
NOTE: The differential/gauge instruments will only
measure positive pressures i.e. positive pressure
applied to positive port, or negative pressure applied
to the negative port.
WARRANTY
This instrument is guaranteed against defects of
workmanship and materials for a period of twelve
months from date of invoice.
During the warranty period a defective instrument will
be repaired or replaced at the discretion of the
manufacturer. This warranty does not cover damage
or failure due to misuse or accident. Modification,
adjustment or any alteration shall void the warranty.
For any warranty claims to be considered the
instrument must be returned to Anton along with proof
of purchase at the senders cost.
FCC Compliance
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at his own
expense.
SPECIFICATIONS
Power Supply
3 x AA Alkaline Batteries
Battery Life
> 20 hours*
Duty Cycle
Continuous.
Auto switch off after 5 mins.
Operating
Temperature
-10 to +50 °C
Weight
395 grams including
batteries
Dimensions
185 x 75 x 43 mm
Accuracy
±2% of reading
* Using recommended Industrial batteries
Units
APM 155
mbar
0.0 to +2000.0
PSI
0.000 to +29.000
mmHg
0.0 to +1500.0
mmH2O
0 to +20394
mH2O
0.000 to +20.394
inHg
0.00 to +59.06
inH2O
0.00 to +802.9
kPa
0.00 to 200.00