CTS CVT-3012SFP User manual

Trademarks
CTS is a registered trademark of Connection Technology
Systems Inc. Contents subject to revision without prior
notice.
All other trademarks remain the property of their owners.
Copyright Statement
Copyright Connection Technology Systems Inc.
This publication may not be reproduced as a whole or in
part, in any way whatsoever unless prior consent has been
obtained from Connection Technology Systems Inc.
FCC Warning
The CVT-3012SFP Series converters have been tested
and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These
standards are designed to provide reasonable protection
against harmful interference when these devices are
operated in a commercial environment. These devices
generate, use, and can radiate radio frequency energy and
may cause harmful interference to radio communications
unless installed in accordance with this User’s Guide.
Operation of these devices in a residential area is likely to
cause harmful interference which will make the user
responsible for the appropriate remedial action at his / her
own expense.
CE Mark Warning
These are Class A products. In a domestic environment
these products may cause radio interference in which case
the user will need to consider adequate preventative
methods.
This is a lead-free and RoHS-compliant product.
1. Checklist
The carton should contain the following items:
-CVT-3012SFP Converter
-AC-DC Power Adapter
-RJ-45 to DB-9 Serial Cable
-User’s Guide
Please notify your sales representative immediately if any
items are missing or damaged.
2. Overview
CVT-3012SFP is designed to meet the massive needs for
Gigabit network deployment and able to extend a copper
based Gigabit network via fiber cable to a maximum distance
up to 80KM.
CVT-3012SFP is fully compliant with IEEE802.3, 802.3u,
802.3ab & 802.3z standards. It can be installed into a CVT
Converter RACK. The installation & operation procedures
are simple and straightforward. Operation status can be
locally monitored through a set of Diagnostic LED indicators
on the front panel.
Features
-
10/100/1000Base-T to 1000BASE-X Converter
-
Standard: IEEE 802.3, 802.3u, 802.3ab & 802.3z
-
Interface: 1 x RJ-45 LAN connector
1 x RJ-45 Console Port
1 x SFP Slot
-
Auto-Negotiation in TP port
-
MDI/MDIX Auto-Crossover supported
-
LED: PWR, F/O Link Act, TP Link Act, TP/FDX, Speed,
COM, Status
-
Plug-and-Play installation
-
Support Link Alarm
-
Support Jumbo Frame (64-9728 Byte)
Note:
Under 10/100Mbps, CVT-3012SFP only supports
packet length from 64 to1532 Byte. Please make sure
that the total packet length is smaller than 1532 Byte
while Tag-VLAN is enabled.
-
Support Selectable ISP Ethernet Tag Type
3. Installation
Attach fiber cable from the CVT-3012SFP to the fiber
network. The fiber connections must be matched –
transmit socket to receive socket.
Attach a UTP cable from the 10/100/1000BASE-T
network to the RJ-45 port on the CVT-3012SFP.
Connect the power adapter to the CVT-3012SFP and
check that the Power LED lights up. The TP Link/Act
and F/O Link/Act LEDs will light up when all the cable
connections are satisfactory.
Attach one end of the RJ-45 to DB-9 serial cable to the
RJ-45 COM port on the front panel of the converter.
Attach the other end to a PC or workstation serial port.
Run a terminal emulation program using the following
settings:
Emulation VT-100/ANSI compatible
BPS 9600
Data bits 8
Parity None
Stop bits 1
Flow Control None
Enable Terminal keys
Figure 1. CVT-3012SFP Converter Front Panel
Figure 2. CVT-3012SFP Converter Rear Panel

4. LED Description
5. Technical Specifications
Standards:
IEEE 802.3, 802.3u, 802.3ab,
802.3z
Interface:
1 X RJ-45 connector
1 X RJ-45 Console port
1 X SFP Slot
Operation LED:
PWR, F/O Link Act, TP Link Act,
TP/FDX, Speed, COM, Status
Power:
I/P AC 100-240V
O/P DC 5V, 1.6A
Power Consumption:
4W
Shipping Weight:
0.6KG
Dimensions:
71mm(W)X94mm(D)X26mm(H)
Temperature:
Operating: 0 ~ 50 oC
Storage: -20 ~ 60 oC
Humidity:
5% ~ 90% RH
Certification:
FCC/CE Class A
*Please contact us for further reports and updates.
Media:
TP EIA/TIA-568 Cat 5E, 1000M
Fiber 50/125, 62.5/125um multi-mode fiber
9/125, 10/125um single-mode fiber
6. DIP SWITCH Setting
The default setting for PIN 1 to PIN 8 is OFF.
Pin NO.
Function
OFF
ON
1
TP
Auto-Negotiation
Enable
Disable
2
Manual Data
Rate 10/100
100
10
3
Reserve
Always OFF
4
Duplex
Full
Half
5
Flow Control
Enable
Disable
6
Auto-Crossover
Enable
Disable
7
Link Alarm
Disable
Enable
8
Fiber Mode
Auto
Force
NOTE:
1
Before changing Data Rate and Duplex mode setting,
please make sure Auto-Negotiation is disabled.
2
Before changing Auto-Crossover setting, please make
sure Auto-Negotiation is enabled.

Contact Information
Connection Technology Systems INC (CTS)
18F-6, No.79, Sec.1, Xintai 5th Rd., Xizhi Dist.,
New Taipei City 221, TAIWAN, R.O.C.
TEL: [phone] FAX: [phone]
E-Mail: [email protected]
CVT-3012SFP
10/100/1000BASE-T to
1000BASE-X (SFP slot)
Standalone Media Converter
User’s Guide
Version 1.8
LED
Color
Function
PWR
Green
Lit when power is available.
TP/Link
Act
Green
Lit when TP cable connection with
remote device is good.
Blink when TP traffic is present.
Orange
Blink when Fiber or Copper link is down
under Link Alarm enabled mode.
FO/Link
Act
Green
Lit when Fiber cable connection with
remote device is good.
Blink when F/O traffic is present.
Orange
Blink when Fiber or Copper link is down
under Link Alarm enabled mode.
TP/FDX
Green
Lit when TP works in Full-Duplex.
Not-Lit when TP work in Half-Duplex.
Speed
Green
Lit when TP work in 100M
Not-Lit when TP works in 10M or is not
linked.
Orange
Lit when TP works in 1000M.
Status
Green
Lit when TP and F/O link is up.
Orange
Lit when TP or F/O link is down.
COM
Green
Lit when Console port is connected.