Cumberland CC2415 User manual

PNEG-620-2
Curtain Controller
Featuring the Enclosed Limit Switch and Pulley Covers
Installation and Operation Manual
PNEG-620-2
Date: 09-20-13

2PNEG-620-2 Curtain Controller
This equipment shall be installed in accordance with the current installation codes and
applicable regulations which should be carefully followed in all cases. Authorities having
jurisdiction should be consulted before installation occurs.

Table of Contents
PNEG-620-2 Curtain Controller 3
Contents
Chapter 1 Safety .....................................................................................................................................................4
Safety Guidelines ...................................................................................................................................4
General Safety Statement ......................................................................................................................5
Chapter 2 Safety Decals ........................................................................................................................................7
Chapter 3 Installation ............................................................................................................................................8
Chapter 4 Header Pulley ......................................................................................................................................11
Cable Configurations ............................................................................................................................11
Chapter 5 Pulley Cover Mounting ......................................................................................................................12
Pulley Cover Mounting Instructions ......................................................................................................12
Chapter 6 Maintenance ........................................................................................................................................13
Chapter 7 Troubleshooting Guide ......................................................................................................................14
Chapter 8 Parts List .............................................................................................................................................15
Enclosed Limit Switch Assembly ..........................................................................................................16
Motor Components ...............................................................................................................................18
Chapter 9 Installation Kit .....................................................................................................................................22
AC180-A Installation Kit (Purchased Separately) ................................................................................22
AC180-B Installation Kit (Purchased Separately) ................................................................................23
Chapter 10 Wall Mount ........................................................................................................................................25
Outside Endwall Mount .......................................................................................................................25
Outside Sidewall Mount ......................................................................................................................26
Inside Endwall Mount .........................................................................................................................27
Chapter 11 Wiring Diagrams ...............................................................................................................................28
Potentiometer Wiring Diagram ...........................................................................................................28
Control Box Wiring ..............................................................................................................................29
Wiring Diagram for 110V 60 Hz ..........................................................................................................30
Wiring Diagram for 220V 50/60 Hz .....................................................................................................31
Chapter 12 Warranty ............................................................................................................................................33

4PNEG-620-2 Curtain Controller
1. Safety
Safety Guidelines
This manual contains information that is important for you, the owner/operator, to know and understand.
This information relates to protecting personal safety and preventing equipment problems. It is the
responsibility of the owner/operator to inform anyone operating or working in the area of this equipment
of these safety guidelines. To help you recognize this information, we use the symbols that are defined
below. Please read the manual and pay attention to these sections. Failure to read this manual and its
safety instructions is a misuse of the equipment and may lead to serious injury or death.
DANGER
WARNING
CAUTION
NOTICE
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a
hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.

1. Safety
PNEG-620-2 Curtain Controller 5
General Safety Statement
Our foremost concern is your safety and the safety of others associated with grain handling equipment.
This manual is to help you understand safe operating procedures and some problems that may be
encountered by the operator and other personnel.
Asownerand/oroperator,youareresponsibleto know what requirements,hazards,and precautions exist
and inform all personnel associated with the equipment or in the area. Safety precautions may be required
from the personnel. Avoid any alterations to the equipment, which may produce a very dangerous
situation, where SERIOUS INJURY or DEATH may occur.
Electrical Safety
An adequate and safe power supply to the Curtain Controller unit is essential for safety. A competent and
qualified electrician must undertake all electrical wiring. All wiring is to be installed according to the
National Standards and Regulations relevant to your Country and Region.
Be sure to properly ground all motors and electrical equipment employed if required by local codes.
Permanent wiring must be installed according to applicable local codes.
User’s Manual
This manual contains information and instructions essential to the safe installation and use of the
Curtain Controller System. Read this manual thoroughly before attempting any installation or use
of the Curtain Controller System. Keep this manual with the Curtain Controller System or in a location
where it can be readily accessed. Failure to read this manual and its safety instructions is a misuse
of the equipment.
Correct Uses of Your Curtain Controller
The Curtain Controller System is designed solely for the purpose of controlling temperature curtains in
livestock (swine and chicken) houses. Use of the system in any other way is a misuse of the system and
may endanger safety and health.
Only genuine AP/Cumberland parts are to be used in the installation and use of the Curtain Controller
System. Use of other non-genuine parts is a misuse of the system and may lead to dangerous situations
imperilling the safety and health of you and others.
Controls
The Curtain Controller is designed for use with manual or automatic temperature control. GSI
recommends the use of genuine GSI controls. Use of any controllers that do not meet this specification
can pose a risk to health and safety and will lead to malfunction and failure of the Curtain Controller.
This machine is not designed for use in atmospheres where there is a risk of explosion. Use of the
Curtain Controller System in such an environment is prohibited. If in doubt, contact your dealer or GSI.
Safety Guards
The Curtain Controller System contains many moving and electrical parts, which will cause serious injury
or death if touched. Guards are placed on the machine for your protection. Operating the machine
at any time with guards removed or incorrectly fitted is a serious misuse of the machine and
endangers safety.

1. Safety
6PNEG-620-2 Curtain Controller
Safety in Handling the Curtain Controller System
The Curtain Controller unit weights:
All precautions should be taken when lifting and/or moving the unit, to prevent the risk of physical injury.
Maximum Load
The Curtain Controllers with 15 RPM and 30 RPM gear motors can lift a maximum of 4000 lbs./1814 kg
at a 2:1 pulley ratio. 60 RPM Gear motors can lift a maximum of 1000 lbs./453 kg at a 2:1 pulley ratio.
Safety in Maintenance
While the Curtain Controller is designed to keep maintenance to a minimum, some maintenance will be
necessary in the course of the life of the machine. Do not attempt any repairs on the machine unless you
are competent to do so. Remember that the Curtain Controller may operate under automatic control and
start without warning. Never attempt any work on the Curtain Controller without first isolating the machine
from the main power and locking the isolator so that only you can turn the power back ON.
Follow all guidelines given in the maintenance section on Page 13 of this manual.
Before restarting the Curtain Controller, ensure that all electrical enclosures are locked closed and all
guards and other safety measures are correctly fitted.
If in any doubt, contact your dealer or GSI for assistance.
Noise
Tests on this machine indicate noise levels at a position one meter from the drive unit, and 1.6 meters
abovetheground do notexceed70 dBa, continuous“A” weighted sound pressureor63 Pa, instantaneous
“C” weighted sound pressure.
Model # Weight
CC2415
104 lbs./47 kg
CC2430
CC2460
I2430-50
CC3615
119 lbs./54 kg
CC3630
CC3660
I3630-50
CC4815
135 lbs./61 kg
CC4830
CC4860
I4830-50
CC6015
151 lbs./69 kg
CC6030
CC6060
I6030-50

PNEG-620-2 Curtain Controller 7
2. Safety Decals
This page shows you exactly where the safety signs should be placed on your Curtain Controller.
If a decal is missing, damaged or unreadable, please contact your dealer or the GSI group, for a
free replacement.
For guidance or assistance on any issues relating to the safe use of the Curtain Controller System,
Contact:
GSI Group
1004 E. Illinois St.
Assumption, IL. 62510
Phone: [phone]
DC-1948 is located above the electrical box on
the outside of the Curtain Controller.
DC-1948 is located on the electrical unit within the Curtain Controller.
DANGERDANGER DANGERDANGER
DC-1948
Lockout power
before servicing.
Will cause serious
injury or death.
HIGH VOLTAGE
Couper/verrouiller le
courant avant l’entretien.
Causera de sérieuses
blessures ou la mort.
HAUTE TENSION
DC-1948GSI Group 217-226-4421
DANGERDANGER DANGERDANGER
DC-1948
Lockout power
before servicing.
Will cause serious
injury or death.
HIGH VOLTAGE
Couper/verrouiller le
courant avant l’entretien.
Causera de sérieuses
blessures ou la mort.
HAUTE TENSION
DC-1948GSI Group 217-226-4421

8PNEG-620-2 Curtain Controller
3. Installation
This manual outlines the recommended sequence for the installation of the Curtain Controller system.
The curtain controller may be installed either inside or outside. Following the sequence will prove the
safest and easiest method of installation. Above all, connection of the system to the electrical mains
should be the final stage of installation. Failure to observe this could lead to a fatal accident.
1. Unpack the Curtain Controller, remove the front cover and inspect the machine for visible defects.
2. Select mounting configuration. (See examples of: wall mount on Pages 25-27.)
3. Screw one 3/8" x 3" lag bolt 6-1/2" below the desired height of the Curtain Controller.
NOTE: Leave 1-1/2" between the bolt head and the wall. (See Figure 3A.)
Figure 3A
4. Using the “keyhole” slot in the back of the Curtain Controller, hang the machine on the 3" lag bolt.
(See Figure 3B.) NOTE: The 3" lag bolt should only be used to hang the machine to the wall.
Do not attempt to operate the machine until it is fully secured.
Figure 3B

3. Installation
PNEG-620-2 Curtain Controller 9
5. Secure the machine to the wall by using the six (6) 3/8" x 2" lag bolts provided. (See Figure 3C.)
Figure 3C
6. Install pulleys, brackets, hand winches etc., according to the appropriate mounting configuration.
7. Install the cabling through the pulleys, brackets, hand winches etc., according to appropriate
mounting configuration. Recommended cable size is 3/16".
8. Install the cable into the Curtain Controller pulley cover and loop the cable around the pulley.

3. Installation
10 PNEG-620-2 Curtain Controller
9. While the drive block is near the closed position (bottom of the drive screw), loop the incoming cable
through the two (2) holes in the drive block as shown in Figure 3D and fasten the cable to itself using
three (3) 3/16" cable clamps per cable.
Figure 3D
10. Wire the Curtain Controller to the appropriate control. (See wiring diagrams on Pages 28-31.)
11. Close the curtains/vents fully using the manual mode of the controls. Set the lower limit using the
lower limit adjustment collar. NOTE: Be sure to tighten the limit switch adjustment collar. Failure to
do so can cause damage to the machine and barn. Take up excess slack in the cable using the
manual winch while paying close attention not to overtighten.
12. Open the curtains/vents to the desired height using the manual mode of the controls. Set the upper
limit switch adjustment collar. NOTE: Be sure to tighten the limit switch adjustment collar. Failure to
do so can cause damage to the machine and barn.
13. Attach the door to the machine. This will protect the integrity of the machine and ensure the safety of
those working on or near the machine.
WARNING
Be sure to properly ground all motors and electrical equipment.

PNEG-620-2 Curtain Controller 11
4. Header Pulley
Cable Configurations
Pulling two (2) curtains with the
Curtain Controller.
Pulling one curtain to the right
of the Curtain Controller.
Pulling one curtain to the left
of the Curtain Controller.
Curtain Controller is mounted
horizontally. Remove the cap plugs
in the top of the machine and run
cables through the top holes.
Pulley Configuration(s)
Used when

12 PNEG-620-2 Curtain Controller
5. Pulley Cover Mounting
Pulley Cover Mounting Instructions
Attaching Pulley Covers to Pre-Existing Cable
NOTE: If you do not have pre-existing cable, drill a 1/4" hole in the appropriate dimple and proceed to Step 4 .
Step 1: Determine on which side of the machine the pulley cover will be mounted. This will affect where
the slot will be cut in Step 2.
Step 2: Using a saw, cut a slot from the bottom of the pulley cover lip to the dimple on the cover’s face.
When slotting the right pulley cover, use the right dimple for placement. When slotting the left
pulley cover, use the left dimple for placement. (See Figure 5A for slot placement.)
Figure 5A
Step 3: Slide the existing cable into the slot until it reaches the dimple.
Step 4: Remove existing sheet metal screw. (See Figure 5B for pulley cover fastening.)
Figure 5B
Step 5: Fasten the pulley cover to the machine using four (4) #10-16 x 5/8" sheet metal screws. The top
of the pulley cover should be flush with the top of the machine.

PNEG-620-2 Curtain Controller 13
6. Maintenance
Safety in Maintenance and Repairs
Before starting any repairs or maintenance on the Curtain Controller System or control units, observe the
following safety steps:
1. Isolate the system from the electricity supply by switching OFF the power isolator and lock it in the
OFF position.
2. Keep the key in your possession.
3. Do not reconnect the power supply until all work is completed and all guards are correctly refitted.
It is recommended that the end user practices a monthly inspection of the Curtain Controller and all items
used in conjunction (cables, pulleys, brackets, hand winches etc.) with the machine.
1. Inspect the drive screw. Lubricate liberally with a lithium grease of an NLGI No. 2 consistency
(extreme pressure properties).
2. Inspect and tighten the locking collars on the adjustment rod to ensure activation of limit switches.
3. Inspect cable, pulleys, brackets, hand winches etc., for alignment and premature wear. Realign
and/or replace as needed.
4. Inspect bearings checking for smooth rotation and listening for squeaks.
5. Inspect set screws in couplers and in pillow block bearing.
6. Manually run machine in both directions to ensure positive shut off and unrestricted cable movement.
7. Inspect drive screw for debris in the threads. Debris in threads may cause premature failure of
drive block.
8. Inspect the thrust bearing. Lubricate as needed.

14 PNEG-620-2 Curtain Controller
7. Troubleshooting Guide
Problem Possible Cause Corrective Action
1. Will not run in manual mode. 1. Control not in manual mode.
2. Toggle switch failure.
1. Move switch to manual setting. Check
for loose wire connection.
2. Replace toggle switch.
1. Machine operates in opposite
direction in response to
temperature change. 1. Control wired incorrectly.
1. Re-wire to wiring schematic instruction.
1. Runs in both directions
(automatic mode), but only one
direction (manual mode). 1. Control failure. 1a. Check for loose wire connection.
1b. Replace control.
2. Will not run in either direction
(manual or automatic modes). 2. No power (circuit breaker or fuse).
3. Tripping may indicate machine
overload or electrical wire short.
Repair or replace before
reenergizing circuit.
4. Motor failure.
2. Check main panel circuit breaker
or fuse.
3. Check control circuit breaker
and/or fuse.
4. Motor designed with internal thermal
protection. Before replacing, allow
motor to cool down and reset. May
indicate machine overload. Contact
factory for machine restrictions.
5. Primary switch failure.
5a. Replace primary switch.
5b. Check to see if secondary switch is
not depressed.
1. Will not run in automatic but does
operate in manual. 1. Control not in automatic mode.
2. Control failure
1. Move switch to automatic setting.
2. Replace control.
1. Runs in one direction only, both
automatic and manual. 1. Broken or loose wire.
2. Limit switch catching on
adjustment rod mechanism.
3. Limit switch failure.
4. Control failure.
1. Repair broken or loose wire.
2. Free switch and adjust as needed.
3. Replace switch.
4. Replace control.

PNEG-620-2 Curtain Controller 15
8. Parts List
1. Enclosed Limit Switch Assembly -(See Pages 16 and 17.)
2. Motor Components -(See Pages 18-21.)

8. Parts List
16 PNEG-620-2 Curtain Controller
Enclosed Limit Switch Assembly

8. Parts List
PNEG-620-2 Curtain Controller 17
Enclosed Limit Switch Assembly Parts List
Ref # Part # Description
152-0323 Limit Switch Box
2 52-0319 Bracket, Limit Switch Support
352-0320 Channel, Electrical Box Mounting 4" x 6"
4 52-0322 Gasket, Flat 4" x 6" Box
552-0318 Lid 4" x 6" Flat
6 50-0144 24" Travel Adjustment Rod
650-0145 36" Travel Adjustment Rod
6 50-0146 48" Travel Adjustment Rod
650-0147 60" Travel Adjustment Rod
7 52-0321 Adjustment Rod Retainer 4" x 6"
850-0159 Adjustment Collar
9 FH-1310 Cord Connector, Heyco
10 FH-1309 Lock Nut 1/2" #401 ARL.
11 52-0331 Water Shield
12 S-2126 1/4" SAE Washer
13 S-7967 Set Screw #10-32 x 1-1/4"
14 S-280 Screw, SDS #10-16 x 5/8" HWH ZN
15 52-0170 Spring, Adjustment Rod Extension
16 S-7377 Screw, MS #10-24 x 1" RHP ZN Grade 2
17 S-849 Hex Nut #10-24 ZN Grade 2
18 S-7974 Straight Actuator Micro Switch
19 S-8810 Screw, SMSAB #4 x 1" PHP ZN

8. Parts List
18 PNEG-620-2 Curtain Controller
Motor Components

8. Parts List
PNEG-620-2 Curtain Controller 19
Motor Components (Continued)

8. Parts List
20 PNEG-620-2 Curtain Controller
Motor Components (Continued)