Curt Manufacturing 70103 User manual

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 1
Product Registration and Warranty
CURT stands behind our products with industry-leading warranties. To get copies of the product
warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys
NOTICE
Visit www.curtmfg.com for a full-color copy of this
instruction manual, as well as helpful videos, guides and much more!
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
This installation requires front fascia panels to be temporarily removed. The tow hooks and
frame rail extensions will not be reinstalled and should be returned to the vehicle owner.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
If equipped, we recommend removing the base plate attachment tabs when not in use.
INSTALLATION MANUAL 70103
WARNING
Never exceed the vehicle manufacturer's recommended gross vehicle weight rating (GVWR).
Parts List
Item Qty Description
1 1 Tow bar base plate, driver
2 1 Tow bar base plate, passenger
3 2 Tow bar mounting tab
4 2 Safety cable, 7,500 lbs.
5 2 Conical washer, 1/2"
6 2 Hex bolt, 1/2"-13, 5", grade 8
7 2 Round hole spacer, 2" x 1/4"
8 2 Quick link, 1/2"
9 2 Socket plug
Tools Required
Torque wrench Drill
Socket, 3/4" Drill bit, 1/4"
Socket, 8mm T27 Torx bit
Socket, 10mm Flat screwdriver
Socket, 15mm Wrench, 3/4"
Socket, 16mm --
CAUTION
Take care when cutting any plastic or metal as injury may occur if done improperly.
Installed Attachment Tabs
Height 20"
Width 37-1/4"
Product Photo
Not pictured: Safety cables, quick links and socket plugs
Level of Difficulty
Difficult
Installation difficulty levels are based on time
and effort involved and may vary depending on
the installer level of expertise, condition of the
vehicle and proper tools and equipment.
SAFETY INSTRUCTIONS
Safety glasses should be worn at all times while installing this product.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 2
5
6
1
7
8
9
4
3
2
A SSEMBLY
Parts List
Item Qty Description
1 1 Tow bar base plate, driver
2 1 Tow bar base plate, passenger
3 2 Tow bar mounting tab
4 2 Safety cable, 7,500 lbs.
5 2 Conical washer, 1/2"
6 2 Hex bolt,1/2"-13, 5", grade 8
7 2 Round hole spacer, 2" x 1/4"
8 2 Quick link, 1/2"
9 2 Socket plug

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 3
FASCIA REMOVAL
Step 1
Open the hood and remove the radiator cover
by pulling out the 13 push pins – six on either
side of the vehicle and one in the center.
Once removed, set the cover aside.
Step 2
Use a T27 Torx bit to remove the two screws
behind the radiator cover attaching the bumper
cover, one on either side of the vehicle.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 4
Step 3
Use an 8mm socket to remove the three wheel
well liner bolts. Then, pull the liner back and
use a 10mm socket to remove the bolt behind
the liner at the fender and bumper cover seam.
Repeat on the other side of the vehicle.
Step 4
Remove the two rivets located on the underside
corner of the front fascia panel – one on either
side of the vehicle. Then, use a 10mm socket to
remove the four underside bolts holding the
fascia in place – two on either side of the vehicle.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 5
Step 5
Starting on the outer edges, insert a screw
driver between the tabs where the screw was
located inside the fender seam and twist to
release the clip. Firmly but carefully pull the
fascia panel out, releasing the clips in the
fender seam. Do not break the tabs!
Work your way toward the center of the vehicle,
unclipping the fascia. It may be required to pull
up on the bumper cover to release the last clips
under the headlights.
Make sure to unplug the foglight wiring
harnesses on both sides if present as well as
the electrical connection on the driver side by
pulling out the yellow clip and sliding the red
lock toward the yellow clip.
Carefully remove the bumper cover
and set aside so it will not be damaged
during the rest of the installation.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 6
Step 6
Use a 16mm socket to remove the two
bolts on the underside of the tow hook
bracket. Then, use a 30mm socket to
remove the backside tow hook nut.
Once removed, set the tow hook aside.
Repeat on the other side of the vehicle.
Step 7
Use a 15mm socket to remove the three bolts
holding the frame extension in place. Then, use
a 10mm socket to remove the nut. Note: certain
models are equipped with a clip instead of a nut.
Repeat on the other side of the vehicle.
Return the tow hooks and frame
extensions to the vehicle owner.
TOW BAR BASE PLATE INSTALLATION

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 7
Step 8
On the driver side, position the tow bar
base plate (#1) and secure it using the
four factory bolts removed in Steps 6 and 7
(one of the tow hook bolts and the three
from the frame extensions).
Torque the bumper bolt first, then the
three frame bolts, each to 45.2 lb-ft.
Repeat on the passenger side of the vehicle.
Step 9
On the backside of the base plate (#1),
install a supplied 1/2" hex bolt (#6) with
a conical washer (#5) and 1/4" thick,
round-hole spacer (#7).
Torque to 110 lb-ft.
Repeat on the other side of the vehicle

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 8
Step 10
Install the permanent safety cables (#4)
and quick links (#8), looping them around the
vehicle frame and linking them to the tow bar
base plates (#1,#2). There must be one cable
on each side of the vehicle.
Make sure the cables do not pinch or interfere
with any hoses, wiring or other components.
See 'Installing the Permanent Base Plate
Safety Cables' for additional information.
Step 11
Reinstall the bumper cover and all panels that
were previously removed and plug in the wiring
harnesses removed in Step 5. Note: To secure
the underside of the fascia, we recommend
installing new push pins or plastic rivets.
When ready to tow, install the tow bar
mounting tabs (#3). When not towing,
insert the socket plugs (#9) into the
ends of the tow bar base plates (#1,#2).

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •70103-INS-RC •04/14/2020 •ECN6926 •PAGE 9
SAFETY CABLE INSTALLATION
ADDITIONAL INFORMATION
Towing Tips
Check your equipment Periodically check the condition of all towing equipment. Ensure all fasteners are tight and
that all structural components are sound. Do not tow with worn or damaged parts.
Towing vehicle and trailer
manufacturer's recommendations
Review the owner's manual for your towing vehicle and trailer
for specific recommendations, capacities and requirements.
Final Installed Image
Installing the Permanent Base Plate Safety Cables
When dinghy towing a vehicle with a tow bar, base plate safety cables should be used at all times.
In the event of a disconnect, the safety cables are designed to help prevent complete vehicle separation.
When installing the safety cables, use the illustrations below as a guide.
Installation guidelines
1. The cables must be connected to
the base plate and the vehicle frame.
2. Two cables must be installed.
3. Each cable must meet or exceed the
gross weight of the towed vehicle.
4. Make sure cables do not pinch or interfere
with hoses, wiring or other components.
Note: Base plate safety cables are not a replacement for safety chains connecting the tow vehicle to the towed vehicle.
BaseplateBaseplate
Quick link Quick link
Permanent baseplate
safety cable
Permanent baseplate
safety cable
Convenience link No convenience link