Curt Manufacturing 13434 User manual

MAKE: STYLE:
MIN.
15
WARNING: NEVEREXCEEDYOURVEHICLE MANUFACTURER'SRECOMMENDEDTOWINGCAPACITY
For more informationlogonto www.curtmfg.com&for helpful towingtipslog ontowww.hitchinfo.com
WEIGHTCARRYING:
INSTALLATIONTIPS:
INSTALLATIONREQUIRES:
VEHICLE PHOTO:
HITCHILLUSTRATION:
REPRESENTATIVEPHOTO
MAKE SUREYOURHITCHMATCHES
LEVEL OF DIFFICULTY: EASY
MODERATE CHALLENGING
1. BEFORE YOUBEGININSTALLATION, READALL
INSTRUCTIONS THOROUGHLY.
2. TO EASEINSTALLATION, 2PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL ANDREDUCE THE
TIMEREQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product.
YEARS: 2020-PRESENT JEEP MODEL: GLADIATOR TRUCK
5,000
500
TRAILER WEIGHT:
TONGUE WEIGHT:
13434 INSTALLATION INSTRUCTIONS
LBS.
LBS.
MIN.
MIN.30
IF YOU ARE HESITANT TOUNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FORADDITIONAL ASSISTANCE.
NOVICEINSTALLTIME:
PROINSTALL TIME:
SCAN FOR
MORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product
voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
10/23/2019
EASY
RATCHETSOCKET
3/4"
TORQUE
WRENCH
NO FRAME DRILLING
FISHWIRE
HARDWARE
HOLE SAW
2"
POWER
DRILL
SAFETY
GLASSES
HEXBIT
SOCKET
1/2"

Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
BOLT, CAR,1/2-13 UNC,1-1/2,GRD8,YZ
10-1028721
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006222
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP623
FHSCS, 3/4-10 UNC, 2, GR810-1034614
1/2" FISHWIRE1_2 FISHWIRE2
5
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
1. Drill through rear bumper cover using a hole saw at
predefined dimple located in center of cover, then
insert 3/4" bolt.
2. Fishwire CM-SP6 spacer and 1/2" carriage bolt through end
of cross member on both sides.
3. Raise hitch into position and loosely secure with 3/4"
bolt followed by 1/2" flange nuts.
4 Torque 3/4" hardware to 320 lb-ft and 1/2" hardware
to 110 lb-ft.
1
2
3
REAR CROSS MEMBER
5
4

Parts List
DESCRIPTIONPART NUMBERQTYITEM
BOLT, CAR,1/2-13 UNC,1-1/2,GRD8,YZ
10-1028721
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006222
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP623
FHSCS, 3/4-10 UNC, 2, GR810-103461
4
1/2" FISHWIRE1_2 FISHWIRE
25
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
5,000 500
7
15
JEEP GLADIATOR
10/23/2019
13434
30
Scan
for more
information
1. Drill through rear bumper cover using a hole saw at predefined dimple located in center of cover, then insert 3/4"
bolt.
2. Fishwire CM-SP6 spacer and 1/2" carriage bolt through end of cross member on both sides.
3. Raise hitch into position and loosely secure with 3/4" bolt followed by 1/2" flange nuts.
4 Torque 3/4" hardware to 320 lb-ft and 1/2" hardware to 110 lb-ft.
NO FRAME DRILLING
FISHWIRE HARDWARE
1
3
2
REAR CROSS MEMBER
5
4
TOOLS REQUIRED
3/4" SOCKET
RATCHET
TORQUE WRENCH
1/2" HEXBIT
2" HOLE SAW
POWER DRILL
1/4" DRILL BIT
SAFETY GLASSES