Curtis G3 ThermoPro TP2T10A3100 User manual

G3 ThermoPro®Series
1.5 Gallon Coffee Brewing System
USER GUIDE
READ AND SAVE THESE INSTRUCTIONS
NOTICE TO INSTALLER: Please leave this booklet with the machine.
'$51'30/5$07&3øøøøø $
'SFW/$

CONTENTS CL26
.H\)HDWXUHV6SHFLÀFDWLRQV6\VWHP5HTXLUHPHQWV..............................................................................................FS26
,PSRUWDQW6DIHJXDUGV............................................................................................................................................... IS2
,QVWDOODWLRQ,QVWUXFWLRQV*HQHUDO...............................................................................................................................II2
,QVWDOODWLRQ,QVWUXFWLRQV/HYHOLQJ:DWHU6XSSO\(OHFWULFDO....................................................................................II11
2SHUDWLQJ,QVWUXFWLRQV ..............................................................................................................................................OI6
&OHDQLQJ,QVWUXFWLRQV%UHZHU ................................................................................................................................. CI1
&OHDQLQJ,QVWUXFWLRQV7KHUPDO'LVSHQVHUV ............................................................................................................CI5
&OHDQLQJ,QVWUXFWLRQV$LUSRW3RXU3RW ....................................................................................................................CI9
3URJUDPPLQJ*XLGH ............................................................................................................................................... 3*
5RXJK,Q'UDZLQJ................................................................................................................................................. 5'
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV0DLQ&KDVVLV........................................................................................... ,3
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV7DQN$VVHPEO\6LQJOH............................................................................ ,3
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV7DQN$VVHPEO\6LQJOH'XDO9ROWDJH ..................................................... ,3
,OOXVWUDWHG3DUWV5HFRPPHQGHG3DUWV7DQN$VVHPEO\7ZLQ .............................................................................. ,3
(OHFWULFDO6FKHPDWLF736$736$..........................................................................................(6
(OHFWULFDO6FKHPDWLF736$ ...................................................................................................................(6
(OHFWULFDO6FKHPDWLF736$736$..........................................................................................(6
(OHFWULFDO6FKHPDWLF737$737$737$ .................................................................(6
(OHFWULFDO6FKHPDWLF737$....................................................................................................................(6
(OHFWULFDO6FKHPDWLF737$....................................................................................................................(6
(OHFWULFDO6FKHPDWLF737$....................................................................................................................(6
7URXEOHVKRRWLQJ*XLGH*HQHUDO............................................................................................................................7*
7URXEOHVKRRWLQJ*XLGH665&LUFXLW ......................................................................................................................7*
(UURU&RGHV .............................................................................................................................................................(&
3URGXFW:DUUDQW\....................................................................................................................................................3:
Contact Information
Wilbur Curtis Co., Inc.
6913 Acco Street | Montebello, CA 90640 US
Phone: [phone] | Toll Free: 800-421-6150
Email: [email protected] | Web: www.wilburcurtis.com
'PSUIFMBUFTUTQFDJmDBUJPOTBOEJOGPSNBUJPOHPUPXXXXJMCVSDVSUJTDPN
5PMM'SFF].POEBZ'SJEBZA.M.- 4:00 P.M.PT
Email: [email protected]
%VFUPDPOUJOVFEQSPEVDUJNQSPWFNFOUUIFQSPEVDUTJMMVTUSBUFEQIPUPHSBQIFEJOUIJTHVJEFNBZWBSZTMJHIUMZGSPNUIFBDUVBMQSPEVDU
51$0/5&/54-*45øø  "

KEY FEATURES/SPECIFICATIONS/SYSTEM REQUIREMENTS FS26
Key Features
• Easy-to-operate, intuitive G3 Digital control module - provides precise control over all aspects of brewing: time,
temperature, volume plus specialty coffee needs from pre-infusion to pulse-brewing to water bypass.
• Built-in Self Diagnostic System – Includes real-time feedback of the brewing process and energy saving mode.
• Stainless steel ThermoPro®WBDVVNTFBMFETFSWFSTLFFQDPGGFFGSFTIIPUBOEnBWPSGVM
• Pre-Set Global Recipes at the Touch of a Single Button – No complex equipment required.
• Centrally located hot water spout for instant hot beverages and other hot water needs.
• Industry’s most effective mineral tolerant design.
6SHFLÀFDWLRQV6HOHFWHG0RGHOV
(OHFWULFDO6XSSO\5HTXLUHPHQWV
02'(/ '(6&5,37,21 3+$6( 92/76 $036 +($7,1*&21),* :,5( :$776 +(57= &$3$&,7<
736$
736$ Single brewer 1 PH 220 V 19.5 A 2 x 2000 W 3W + G 4300 W 50/60 Hz 12.0 gal/hr
[45.4 l/hr]
736$ Single brewer 1 PH 230 V 20.0 A 2 x 2000 W 2W + G 4600 W 50/60 Hz 12.0 gal/hr
[45.4 l/hr]
736$
736$ Single brewer, dual voltage 1 PH 120/220 V 15.0/12.7 A 2 x 1600 W 2/W3W + G 1800/2800 W 50/60 Hz 4.5/12.0 gal/hr
[17.0/45.4 l/hr]
737$
737$
737$
Twin brewer 1 PH 220 V 23.0/34.5 A 3 x 2500 W 3W + G 5100/7600 W 50/60 Hz 21.0 gal/hr
[79.5 l/hr]
737$ Twin brewer, 3 Phase (Transformer) 3 PH 220 V 20.0 A 3 x 2500 W 3W + G 7600 W 50/60 Hz 21.0 gal/hr
[79.5 l/hr]
737$ Twin brewer, 3 Phase 3 PH 220 V 20.0 A 3 x 2500 W 4W + G 7600 W 50/60 Hz 21.0 gal/hr
[79.5 l/hr]
737$ Twin brewer 1 PH 230 V 24.2 A 2 x 2500 W 2W + G 5574 W 50/60 Hz 21.0 gal/hr
[79.5 l/hr]
'LPHQVLRQV :DWHU6XSSO\5HTXLUHPHQWV
02'(/ +(,*+7 :,'7+ '(37+ 6+,3:(,*+7 6+,3&8%( :$7(5&211(&725 :$7(535(6685( 0,1)/2:5$7(
736$
736$
736$
736$
736$
35.13”
[89.2 cm]
11.13”
[28.3 cm]
20.75”
[52.7 cm]
56.0 lbs.
[24.4 kg]
9.6 cu. ft.
[0.27 m3]µÁDUH
20 - 90 psi
[138 - 620 kPa]
1.0 gpm
[3.8 lpm]
737$
737$
737$
737$
737$
737$
35.13”
[89.2 cm]
20.13”
[51.1 cm]
20.75”
[52.7 cm]
75.0 lbs.
[34.0 kg]
14.3 cu. ft.
[0.40 m3]µÁDUH
20 - 90 psi
[138 - 620 kPa]
2.0 gpm
[7.6 lpm]
TP2, KEY FEATURES/SPECS/SYSTEM REQUIREMENTS 072320B
Following are the factory default settings for the ThermoPro brewer:
• Brew Volume = Large-Medium-Small
• Energy Save Mode = Off
• Brew Temperature = 200°F (92°C)
• Water Bypass = On LARGE and MEDIUM brew only

IMPORTANT SAFEGUARDS IS2
Symbols
This is the safety alert symbol. It is used to alert you to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury or death.
DANGER - Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
WARNING - Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION - Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE - Indicates a situation which, if not avoided, could result in property damage.
IMPORTANT - Provides information and tips for proper operation.
SANITATION REQUIREMENTS
Important Safeguards/Conventions
WARNING:
• Make sure that this appliance is installed and grounded according to the INSTALLATION
INSTRUCTIONS by qualimed personnel before attempting to use it. Failure to follow the INSTALLATION
INSTRUCTIONS could result in personal injury or void the warranty.
• This appliance is designed for commercial use. Any service other than cleaning and preventive
maintenance should be performed by an authorized Wilbur Curtis service technician.
• To reduce the risk of mre or electric shock, DO NOT open the service panels. There are no user
serviceable parts inside.
• Keep hands, arms and other items away from hot surfaces of the unit during operation.
• Clean the appliance and any dispensers completely before using them for the mrst time according to
the CLEANING INSTRUCTIONS. Clean them regularly as instructed in the CLEANING INSTRUCTIONS.
• Use this appliance only for its intended use, brewing/dispensing hot and/or cold beverages/water.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
• Avoid spillage onto the power (mains) connector.
COFFEE/TEA BREWERS, IMPORTANT SAFEGUARDS/SYMBOLS 121622J
WARNING - This product can expose you to chemicals including Acrylamide and Bisphenol A (BPA),
which are known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information visit www.P65Warnings.ca.gov.

IMPORTANT SAFEGUARDS IS2
COFFEE/TEA BREWERS, IMPORTANT SAFEGUARDS/SYMBOLS 121622J
CE Requirements
• This appliance must be installed in locations where it can be overseen by trained personnel.
• For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C.
• This appliance is not suitable for outdoor use.
• This appliance shall not be tilted more than 10° for safe operation.
• An electrician must provide electrical service as specimed in conformance with all local and national codes.
For safe use, an all-pole disconnection must be incorporated into the mxed wiring in accordance with the
wiring rules outlined in clause 7.12.2 of IEC 60335 for meeting the minimum electrical safety of this standard.
• This appliance must not be cleaned by water jet.
• This appliance can be used by persons aged from 18 years and above if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Keep the appliance and its cord out of reach of children aged less than 18 years.
• Appliances can be used by persons 18 years and above with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved.
• Children under the age of 18 years should be supervised to ensure they do not play with the appliance.
• If the power cord is ever damaged, it must be replaced by the manufacturer or authorized service personnel
with a special cord available from the manufacturer or its authorized service personnel in order to avoid a
hazard.
• Machine must not be immersed for cleaning.
• Cleaning and user maintenance shall not be made by children unless they are older than 18 years and
supervised.
• This appliance is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, ofmces and other working environments;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments.
• This appliance not intended to be used in applications such as:
– farm houses
• Access to the service areas permitted by Authorized Service personnel only.
• The A-Weighted sound pressure level is below 70 dBA.
Disposal of Equipment
• This product contains plastic, metal and electronic components and is considered e-waste. At the end of
its life, this product must not be disposed of in normal household waster but can be instead delivered to a
collection point for recycling electric and electronic appliances, consult with the local municipality for proper
disposal guidelines.

INSTALLATION INSTRUCTIONS II2
Installation Instructions
Installation Requirements
• A secure surface capable of supporting the weight of the appliance.
• For units without an attached cord set attached or dual voltage units set up for use with 220 - 240 Volts:
"QQSPQSJBUFMZTJ[FE6-MJTUFEHSPVOEJOHUZQFQPXFSDBCMFUPNFFUUIFFMFDUSJDBMTQFDJmDBUJPOTGPSUIF
BQQMJBODF*GZPVIBWFRVFTUJPOTBCPVUUIFDPSSFDUDBCMFTJ[FBOEMFOHUIDPOTVMUBRVBMJmFEJOTUBMMFS*GUIF
appliance will be hard wired to a junction box, the power cable must be long enough so that the unit can be
moved for cleaning underneath.
• "HSPVOEFEFMFDUSJDBMDPOOFDUJPOUPBOFMFDUSJDBMDJSDVJUUIBUNFFUTUIFFMFDUSJDBMTQFDJmDBUJPOTPGUIF
appliance (see SPECIFICATIONS). The circuit must be protected by the appropriate sized circuit breaker. If
you are not certain that the existing circuit meets the requirements for your unit, consult a licensed electrician.
• "XBUFSmMUSBUJPOTZTUFNJTSFRVJSFEUPNBJOUBJOUSPVCMFGSFFPQFSBUJPO8JMCVS$VSUJT$P*ODSFDPNNFOETB
8JMCVS$VSUJTBQQSPWFEXBUFSmMUFS4FFUIF$VSUJT&RVJQNFOU$BUBMPHGPSBGVMMMJOFPG8JMCVS$VSUJTBQQSPWFE
XBUFSmMUFST
• 1PUBCMFXBUFSTVQQMZMJOFDPOOFDUJPOGSPNUIFXBUFSmMUFSDBQBCMFPGTVQQMZJOHUIFNJOJNVNnPXSBUFSFRVJSFE
CZUIFTQFDJmDBUJPOT5IFXBUFSTVQQMZMJOFNVTUCFBCMFUPDPOOFDUUPUIFnBSFmUUJOHPOUIFCBDLPGUIF
VOJU4FFUIFSPECIFICATIONS section for the correct size. The water line should also be capable of being
controlled by a shut off valve. Do not connect the water line to a saddle valve or needle valve.
*&$SFRVJSFTUIFGPMMPXJOHXBUFSDPOOFDUJPO
1A quick disconnect or additional coiled tubing (at least two times the depth of the appliance) is required
so that it can be moved for cleaning underneath.
2 5IJTFRVJQNFOUJTUPCFJOTUBMMFEXJUIBEFRVBUFCBDLnPXQSPUFDUJPOUPDPNQMZXJUIBQQMJDBCMF
federal, state and local codes.
 8BUFSQJQFDPOOFDUJPOTBOEmYUVSFTEJSFDUMZDPOOFDUFEUPBQPUBCMFXBUFSTVQQMZTIBMMCFTJ[FE
installed and maintained in accordance with federal, state and local codes.
WARNING:*OTUBMMBUJPOJTUPCFQFSGPSNFEPOMZCZBRVBMJmFEJOTUBMMFS
WARNING: Improper electrical connection may result in an electric shock hazard or damage the unit. This
appliance must be properly grounded.
NOTICE: DO NOT connect this appliance to a hot water supply. The water inlet valve is not rated for hot
water. Do not exceed the maximum water pressure stated in the SPECIFICATIONS section.
IMPORTANT: Observe all governing codes and ordinances.
#3&8&34=41&$*"-5:%*41&/4&34(&/&3*$*/45"--"5*0/*/4536$5*0/4 F
5IF*OUFSOBUJPOBM1MVNCJOH$PEFPGUIF*OUFSOBUJPOBM$PEF$PVODJMBOEUIF'PPEBOE%SVH"ENJOJTUSBUJPO
'%"'PPE$PEFNBOVBMEJSFDUUIBUUIJTFRVJQNFOUNVTUCFJOTUBMMFEXJUIBEFRVBUFCBDLnPX
QSFWFOUJPOJODPNQMJBODFXJUIGFEFSBMTUBUFBOEMPDBMDPEFT'PSVOJUTJOTUBMMFEPVUTJEFPGUIF64"
make sure that the installation is in compliance with the applicable plumbing/sanitation code for your area.

INSTALLATION INSTRUCTIONS II11
Front
panel
Style may vary
Style may vary
Front
panel
Terminal
block
Terminal
block
Installation
Leveling
1 Position the brewer on the counter top. Level it left to
right and front to back by turning the bottom of the
legs.
Connect the Water Supply
2 Flush the water supply line prior to installation to
QVSHFBJSBOEEFCSJTGSPNUIFXBUFSmMUFSBOEUVCJOH
3 $POOFDUUIFXBUFSTVQQMZMJOFUPUIFnBSFmUUJOHPO
the back of the brewer. Leave the water supply valve
closed until the power is connected.
Connecting the Power Cord (units without power cord
installed or units being converted from 120 Volt to 200
- 240 Volt operation)
4 Remove the screws that hold the front panel in place
and remove it.
5 Loosen the strain relief on the back of the brewer.
6On units equipped with an existing 120 Volt power
cord, disconnect the cord from the terminal block
and remove it. Locate, disconnect and cap the
jumper wire between the “C” and “N” terminals on the
terminal block.
7 Feed the end of the power cable, through the strain
relief and into the unit and connect it to the power
block according to the ELECTRICAL SCHEMATIC.
8Tighten the strain relief and replace the front panel.
9If a power plug will not be used, connect the power
cable wires directly to the terminals in the junction
box. See the ELECTRICAL SCHEMATIC for the power
supply requirements.
WARNING: Use the leveling legs to level the
brewer only. Do not use them to adjust brewer
height. Do not extend them higher than necessary.
WARNING: Turn off power to the circuit at the
circuit breaker panel before connecting the power
cable to the brewer. Lock out and tag the circuit
breaker.
(5)&3.0130.*-"/0*/45"--"5*0/*/4536$5*0/4ø 092519E
TPX2, TP2 and TPC2 Series
TPX1 and TP1 Series

INSTALLATION INSTRUCTIONS II11
Installing the Power Plug (units that do not have a
pre-installed plug and will be connected to a power
receptacle)
10 Connect the appropriate type of grounded power plug
to the end of the power cord coming from the back of
the unit.
Powering up the Unit
Units Operating with a power plug:
11 Connect the power plug to the appropriate type of
electrical outlet.
All Units:
12 Turn on the water supply valve.
13 Make sure that the circuit breaker supplying power to
the unit is on.
14 Turn the toggle switch on the back of the brewer to the
0/QPTJUJPO5IFXBUFSUBOLXJMMTUBSUUPmMM8IJMFUIF
UBOLJTmMMJOHJOTQFDUUIFXBUFSTVQQMZMJOFGPSMFBLT
Connect the Brewer Wiring (cont.)
WARNING: Connect the power cord to the
appropriate type and size electrical outlet. If the
electrical outlet is not compatible with the power
cord, have it upgraded by a licensed electrician. Do
not modify the power plug. Do not use an extension
cord. Do not use a power cord/plug that is damaged.
(5)&3.0130.*-"/0*/45"--"5*0/*/4536$5*0/4ø 092519E
Back of brewer
Required plug style
varies with circuit
requirements
15 On models that do not come with the control panel
label installed, determine if the brewer will be setup
for one, two or three batch mode. Find the appropriate
label, included with the brewer. The three batch label
IBT-"3(&.&%BOE4."--#3&8POJUUIFUXP
CBUDIMBCFMIBT-"3(&BOE4."--#3&8POJUBOE
UIFPOFCBUDIIBTPOMZ#3&8POJU1FFMUIFQSPUFDUJWF
CBDLJOHPGGPGUIFEFTJSFEMBCFMBOEBGmYJUUPUIFGSPOU
of the universal control module (UCM). Go to the
PROGRAMMING GUIDE section and program the
brewer for the correct model and batch number.
continued...

INSTALLATION INSTRUCTIONS II11
(5)&3.0130.*-"/0*/45"--"5*0/*/4536$5*0/4ø 092519E
Powering up the Unit (cont.)
16 8IFOUIFXBUFSMFWFMJOUIFUBOLSJTFTUPUIFDPSSFDU
volume, the heating elements will turn on automatically.
Depending on the incoming water temperature and
UIFFMFDUSJDBMTQFDJmDBUJPOTUIFXBUFSUBOLUZQJDBMMZ
requires 20 to 30 minutes to reach the factory set
PQFSBUJOHUFNQFSBUVSF8IFOUIFXBUFSIBTIFBUFE
“Ready to Brew” should be on the display.
17 #FGPSFCSFXJOHGPSUIFmSTUUJNFEJTQFOTFP[
ml of hot water through the hot water faucet to help
purge air from the tubing inside the brewer.
18 Brew a cycle of at least 12 oz./350 ml, to purge any
remaining air from the tubing. See OPERATING
INSTRUCTIONS. During the initial brew cycle and
XIFOFWFSUIFmMUFSJTSFQMBDFEZPVNBZIFBSUIF
TPVOETPGBJSCFJOHQVSHFEGSPNUIFmMUFSUVCJOHBOE
water tank.
IMPORTANT: 8IFOPQFSBUJOHUIFVOJUBUIJHIFS
elevations, reduce the default operating
temperature (200°F/92°C) by 2°F/1°C for each
1000 feet (300 m) of elevation above 4000 feet
(1200 m). See PROGRAMMING GUIDE.

OPERATING INSTRUCTIONS OI6
5101&3"5*/(*/4536$5*0/4øø 072320B
Brewing Instructions
2 Center an empty dispenser
under the brew basket. Make
sure the satellite is pushed
all the way back against the
front cover and is making
contact with the electrical
socket. For best results, pre-
heat the dispenser with 12
oz. (350 ml) min. of hot water
for 1 min. then dump out.
3 *OTFSUBDMFBOQBQFSmMUFSJOUP
the brew basket.
4 Fill with the proper amount
of ground coffee. Level the
DPGGFFJOUIFmMUFS
5 4MJEFUIFmMMFECSFXCBTLFU
into the brew rails under the
control panel. Slide it all the
way back until it stops.
The brewer will brew coffee or tea based on the settings programmed into the universal control module (UCM). To
change the settings, see the PROGRAMMING GUIDE section.
1 The brewer should be ON.
$POmSNUIJTBUUIFSFBS
toggle switch. “Ready to
brew” should be on the
display. If the brewer is
connected to an inter-lock
grinder, the grinder should
be on. When inter-lock
connection is made, grind
coffee at this time.
6 Press the brew button.
Brewing will begin
immediately.
WARNING - TO AVOID SCALDING, AVOID SPLASHING. Keep body parts clear of the brewer during
brewing. Do not remove the brew basket while “Brewing” appears on the display.
The G3 ThermoPro Brewer is factory preset for optimal performance.

NOTICE - Do not use cleaning liquids, compounds or powders containing chlorine (bleach) or corrosives.
5IFTFQSPEVDUTQSPNPUFDPSSPTJPOBOEXJMMEBNBHFUIFmOJTIFT USE OF THESE PRODUCTS WILL VOID
THE WARRANTY.
CLEANING INSTRUCTIONS CI1
Cleaning The Brewer - Daily
BREWERS - GENERIC, CLEANING INSTRUCTIONS 080416B
WARNING: HOT SURFACES - To avoid injury, allow the brewer and dispenser(s) to cool before cleaning.
The brewer should be OFF.5VSOUIFCSFXFSPGGCZnJQQJOHUIFSFBSUPHHMFTXJUDIUPUIF0''QPTJUJPO
1 Remove the dispenser(s). Wipe exterior brewer surfaces with a damp cloth to remove spills and debris.
2 Remove the brew basket(s) and clean them in a mild detergent solution. Use a soft bristled brush for hard to
clean areas. Rinse with clean water, then dry.
3 Wipe the spray head area with a cloth soaked in a mild detergent solution. Rinse with a cloth soaked with
clean water removing any residual detergent. Use a clean, soft cloth to dry.
4 Dump out the drip tray(s) (if applicable). Rinse with clean water, then dry with a soft, clean cloth.
Cleaning The Brewer - Weekly
The brewer should be OFF.5VSOUIFCSFXFSPGGCZnJQQJOHUIFSFBSUPHHMFTXJUDIUPUIF0''QPTJUJPO
1 Remove the spray head(s), unscrewing counterclockwise from the dome plate.
2 Thoroughly clean and rinse the dome plate area.
3 Clean the brew basket rails with a brush soaked with a mild detergent solution. Rinse the area with a cloth
soaked with clean water, removing any residual detergent.
4 Dry the area with a soft, clean cloth.
5 Reattach the spray head(s).
WARNING: DO NOT immerse the brewer in water or any other liquid.

Cleaning the Thermal Dispenser (Daily)
CLEANING INSTRUCTIONS CI5
1.0/1.5 GALLON THERMAL DISPENSER, CLEANING INSTRUCTIONSø D
WARNING: DO NOT immerse the dispenser or lid in water or any other liquid. Do not place the dispenser
or lid in a dishwasher. Doing so will void the warranty. Do not use harsh powders or cleansers containing
chlorine. Do not use a wire brush or scouring pad to clean inside the liner. To avoid damage, DO NOT
use a brush to clean the faucet or the inside of the faucet shank (outlet).
Cleaning the Container
1 Remove the lid. Rinse the dispenser and lid.
 Wash - Prepare a mild solution of detergent and warm
water. Wipe the exterior surfaces of the container and
the lid with a sponge moistened with the detergent
solution to remove spills and debris. Using the supplied
CSVTIDMFBOJOTJEFUIFmMMUVCFPOUIFMJE'JMMUIFMJOFS
with the detergent solution. Use a sponge brush to
scrub out the stainless steel liner.
3 Rinse - Rinse out the liner and lid with clean, warm
water.
4 Sanitize - Reattach the lid, remove the cover and
center the hole under the brew basket on the brewer.
'PSHBM-EJTQFOTFSTESPQone TABZ Z95
UBCMFUJOUPUIFCSFXCBTLFU'PSHBM-
dispensers, drop two TABZ Z61 tablets into the brew
CBTLFU4MJEFUIFCSFXCBTLFUXJUIKVTUUIFUBCMFU<T>
JOTJEFJOUPUIFCSFXSBJMTPOUIFCSFXFS3VOBCSFX
cycle and allow the liner to soak for 5 to 10 minutes
BGUFSnVJETUPQTnPXJOH
5 0QFOUIFGBVDFUBOEESBJOPVUUIFTBOJUJ[FSUPDMFBOUIF
GBVDFUTIBOL
6 'JMMUIFMJOFSUPUIFUPQXJUIDMFBOXBSNXBUFSBOEESBJO
UISPVHIUIF GBVDFUUPSJOTFUIFGBVDFUTIBOL
 'JMMUIFMJOFSUPUIFUPQXJUIXBUFSBTFDPOEUJNFBOE
drain through the faucet. Rinse the lid thoroughly,
pouring water through the brew-through hole and tube,
during rinsing.
continued...
Style varies
The following cleaners are required to properly maintain the thermal dispenser:
• Mild solution of dish-washing detergent and warm water
• TABZ™Coffee Equipment Cleaner Tablets*
• One-Pro Beverage Equipment Cleaner
* For 1.5 gal./5.7 L dispensers use type Z95 (Curtis PN WC-79000)
For 1.0 gal./3.8 L dispensers use type Z61 (Curtis PN WC-79003)
Lid Cover
Stem*
*Some versions
Fill tube
WASH
IMPORTANT: Some dispensers have a stem on the bottom of the lid with a built-in sensor used for the
'SFTI5SBD®feature. Keep this stem free from coffee oil build-up for proper operation.
or
see text
1R¿OWHURU
coffee
SANITIZE

CLEANING INSTRUCTIONS CI5
("--0/5)&3."-%*41&/4&3$-&"/*/(*/4536$5*0/4ø D
 Disassemble the faucet - Unscrew the handle/
bonnet assembly from the top of the faucet and
remove it. Inspect the seat cup for wear. Replace the
seat cup if it is damaged.
%JTBTTFNCMFUIFTJHIUHBVHFTPNFWFSTJPOT
Unscrew the cap and guard to dis-assemble.
Remove the glass tube. Inspect it for cracks or
chips. If broken, replace the glass with a new one.
9 Air Dry - Turn the container and lid upside down
and allow to air dry.
Cleaning the Faucet Parts and Site Gauge
10 Wash - Wash allGBVDFUBOEHBVHFHMBTTQBSUTJG
BQQMJDBCMFXJUIUIFEFUFSHFOUTPMVUJPO$MFBOUIF
inside of the gauge glass with a gauge brush soaked
with detergent solution.
11 Rinse - Thoroughly rinse all parts with clean, warm
water.
 Sanitize - After rinsing, place all faucet and gauge
parts in a sink to be sanitized. Immerse them in One-
1SPDMFBOFSNJYFEBUBSBUJPPGP[HQFSHBM
-PGIPUXBUFS¡'¡$NJO"MMPXUIFQBSUT
to soak for 15 minutes.
13 Air Dry - Remove the faucet parts from the
sanitizer, rinse thoroughly and allow them to air dry.
14 Reassemble - When dry, reassemble the handle/
bonnet. Hand tighten the handle/bonnet onto the
top of the faucet assembly, reinstall the site gauge
JGBQQMJDBCMF*GSFQMBDJOHBCSPLFOHBVHFHMBTT
carefully remove any traces of glass from the silicone
parts before inserting the new gauge glass tube.
Reinstall the lid.
WASH
RINSE
SANITIZE
Cleaning the Thermal Dispenser (cont.)
Faucet
Assembly
Style varies
Seat cup
Handle
Bonnet
Cap
Lid
Washer
Washer
Guard
Glass tube
Float

Cleaning the Airpot/Pour Pot (Daily)
CLEANING INSTRUCTIONS CI9
10631054"*31054$-&"/*/(*/4536$5*0/4ø #
WARNING: DO NOT immerse the airpot/pour pot or lid assembly in water or any other liquid. Do not place the
airpot/pour pot or lid in a dishwasher. Placing a airpot or pour pot in a dishwasher will void the warranty.
Cleaning Airpots
 Wash - Wipe the exterior surfaces of the airpot and
lid with a sponge soaked with the detergent solution
to remove spills and debris. Fill the liner with the
detergent solution. Use a sponge cleaning brush to
clean inside. Clean the spout/siphon tube with the
detergent solution.
 Rinse - Rinse the airpot and the spout/siphon tube
with clean, warm water.
3 Sanitize - Sanitize the interior of the airpot, the
spout/siphon tube and the lid, using a commercial
sanitizer suitable for food grade applications. Swab,
brush or pressure spray the sanitizing solution
according to the directions on the package.
 Air Dry - Turn the airpot and lid upside down.
Allow all parts to air dry.
Cleaning Pour Pots
 Wash - Wipe the exterior surfaces of the pour pot
and lid with a sponge soaked with the detergent
solution to remove spills and debris. Fill the liner with
the detergent solution. Use a sponge cleaning brush
to clean inside.
 Rinse - Rinse the pour pot and the lid with clean,
warm water.
3 Sanitize - Sanitize the interior of the pour pot and
the lid, using a commercial sanitizer suitable for
food grade applications. Swab, brush or pressure
spray the sanitizing solution according to the
directions on the package.
 Air Dry - Turn the pour pot and lid upside down
and allow to air dry.
Start by preparing a mild solution of detergent and warm water. Remove the airpot/pour pot from the brewer and
remove/open the lid. On airpots, remove the nozzle assembly. Rinse.
Nozzle
assembly
TLXA2201G000 shown. Appearance and size varies
with model number.
CLXP6401S100 shown. Appearance and size varies
with model number.
NOTE: The stem on the bottom of TFT series pour pot lids have a built-in sensor used for the FreshTrac®
feature. Keep this stem free from coffee oil build-up for proper operation. After cleaning, inverting the lid
GPSTFDPOETSFTFUTUIF'SFTI5SBDUJNFS

Label style may vary
Label style may vary
Entering
Programming Mode
Enter Code
- - - -
Wilbur Curtis
Wilbur Curtis
Ready to Brew*
Global Recipes
<-- Select --> Language <-- Select -->
Non-Brew Prog
<-- Select -->
Brew Button Prog
<-- Select --> Model Select
<-- Select --> Exit
<-- Select -->
Program menus
<-- Select -->
Program Menus
<-- Select -->
See Global
Recipes Menu
section
See Brew Button
Programming Menu
section
See Model
Select Menu
section
See
Language Menu
section
See Non-Brew
Programming Menu
section
Press ~Press ~Press ~Press ~Press ~Press ~
* “Ready” on some models
With unit OFF, press and hold
bottom right BREW button (4).
Then press and release
ON/OFF button (2). Continue to
hold down BREW button until
Enter Code appears.
Enter 4 digit code.
(factory default = 1-2-3-4)
To enter programming mode:
PROGRAMMING GUIDE PG2
IMPORTANT: All programming functions are performed
with the three center buttons.
The symbols below the buttons are:
 Ż Scroll LEFT/UP (1)
~SELECT or ENTER to save new parameter (2)
ŹScroll RIGHT/DOWN (3)
Once you enter programming mode, press Żor Źto scroll LEFT
or RIGHT to the various menus (Global Recipes, Non-Brew Prog,
Brew Button Prog, etc.). Press ~(SELECT) to enter a menu. Then
press Żor Źto scroll UP or DOWN through a menu. When the
desired menu item appears on the screen, press ~(SELECT) to
access. See Programming Options for detailed descriptions.
8$130(3"..*/((6*%&ø H

Programming Options
See the previous page for instructions on accessing each individual menu.
Some menus save and exit automatically when a parameter is updated. Other menus exit to the previous menu
when a parameter is saved. To exit, press Źuntil EXIT appears on the display, then press ~.
Global Recipes Menu
Select from the following coffee recipes: Gourmet STD (standard), Light Roast, Dark Roast, High Yield, Filter
Pack, or Decaf. The factory default setting is Gourmet STD. Selecting the recipe sets the temperature and
brew settings to the factory recommended settings for the recipe selected. If desired, the individual brew
settings may be changed once the recipe has been selected to meet your brewing needs as shown in the
Brew Settings section.
IMPORTANT: If you change any of the brewer settings on the following pages, some or all of them
NBZCFNPEJmFEJGZPVDIBOHFUIFDPGGFFSFDJQFBGUFSXBSEVTJOHUIFGlobal Recipes Menu.
Press ~
Filter Pack
<-- Select -->
Hight Yield
<-- Select -->
Dark Roast
<-- Select -->
Global Recipes
<-- Select -->
Gourmet STD
<-- Select -->
Select ~Select ~
Select ~
Select ~
Select ~Select ~
Light Roast
<-- Select -->
Press ~
Exit
<-- Select -->
Decaf
<-- Select -->
PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H
Recipe Default Brew Settings
(all models except TP1 series)
Temperature Pulse
Brew
Bypass
Large
Bypass
Medium
Bypass
Small
Pre-
Infusion
Gourmet
STD 200°F/92°C C 35% 10% 0% OFF
Light
Roast 200°F/92°C C 45% 15% 0% OFF
Dark
Roast 196°F/91°C OFF 25% 5% 0% 60/60
High
Yield 192°F/89°C OFF 35% 10% 0% 60/60
Filter
Pack 200°F/92°C C 0% 0% 0% OFF
Decaf 200°F/92°C C 0% 0% 0% OFF
Recipe Default Brew Settings
(TP1 series)
Temperature Pulse
Brew
Bypass
Large
Bypass
Small
Pre-
Infusion
Gourmet
STD 200°F/92°C C 10% 0% OFF
Light
Roast 200°F/92°C C 15% 0% OFF
Dark
Roast 196°F/91°C OFF 5% 0% 60/60
High
Yield 192°F/89°C OFF 10% 0% 60/60
Filter
Pack 200°F/92°C C 0% 0% OFF
Decaf 200°F/92°C C 0% 0% OFF

PROGRAMMING GUIDE PG2
Non-Brew Programming Menu
Temperature - sets the brewing temperature of the water held in the water tank. The factory default setting is
'¡$(PVSNFU45%5IFTFUUJOHSBOHFJT'UP'¡$UP¡$0ODFBDDFTTFEQSFTTŻor
Źto choose the desired temperature. Then press ~to set and exit.
Energy Save Mode - saves energy during periods when the brewer is not in use. The factory default setting is
0GG8IFOTFUUP0OPS0O'UIFCSFXFSBVUPNBUJDBMMZTIVUTPGGGPVSIPVSTUXPIPVSTPOPMEFSVOJUTBGUFS
UIFMBTUCSFXDZDMF1SFTTUIF0/0''CVUUPOUPSFUVSOUPOPSNBMPQFSBUJPO6TFUIF0O'TFUUJOHUPSFBDI
CSFXJOHUFNQFSBUVSFGBTUFS0O'LFFQTUIFXBUFSUFNQFSBUVSFBU'$EVSJOHQFSJPETPGOPOVTF
Once accessed, press Żor Źto choose the desired setting. Then press ~to set and exit.
Brew Count Odom - When accessed, this feature displays the total brew cycles since the odometer was last
reset. Press Żto exit or ~reset and exit.
Quality Timer -(FNJOJNPEFMTOPUJmFTUIFVTFSUIBUUIFDPGGFFJTOPMPOHFSGSFTI4FFUIFINTELLIFRESH®
FEATURES section for a complete description of how the timer operates. The factory default setting is 2 hours
0GGGPS(&.4BOE(&.5NPEFMT5IFTFUUJOHSBOHFJTNJOVUFTUPIPVSTGPS(&.4*'(&.5*'TFSJFTBOE
NJOVUFTUPIPVSTNJOVUFTGPS(&.9TFSJFT0ODFBDDFTTFEQSFTTŻor Źto choose the desired
setting. Then press ~to set and exit.
continued...
8$130(3"..*/((6*%&ø H
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Select ~
Press ~
Select ~
Select ~
Select ~
Select ~
Exit
<-- Select -->
Press ~
Energy Save Mode
<-- Select -->
Brew Count Odom
<-- Select -->
Brew Count Total
<-- Select -->
Master Reset
<-- Select -->
Temperature
<-- Select -->
Quality Timer
<-- Select -->
Cold Brew Lock
<-- Select -->
Non-Brew Prog
<-- Select -->
P-Maintenance
<-- Select -->
Warmers Default
<-- Select -->
Service Call
<-- Select -->
Access Code
<-- Select -->
Banner Name
<-- Select -->
Warmers Auto-Off
<-- Select -->
Beeper On/Off
<-- Select -->
Display Messages
<-- Select -->
Display Timers
<-- Select -->
Satellite Color
<-- Select -->
Server Lockout
<-- Select -->
Display Brew Time
<-- Select -->
QT Alarm On/Off
<-- Select -->
1
1,2
1,2
Drip-Out Mode
<-- Select -->
2 Visible only when model selected =
GEMX (Twin or Single)
1 Visible only when model selected =
Gemini or Gemini-IF (Twin or Single)

Non-Brew Programming Menu (cont.)
Brew Count Total - when accessed, displays the total brew cycles on the brewer. It cannot be reset. The
display returns to the previous screen automatically after a few seconds.
Cold Brew Lock - adjusts the temperature at which the brewer will brew coffee when the BREW button is
pressed (Ready to BrewBQQFBSTPOUIFEJTQMBZ5IFGBDUPSZEFGBVMUTFUUJOHJT'¡$CFMPXUIFXBUFSUBOL
temperature setting. This feature also adjusts the temperature at which the heating element turns on to reheat
UIFXBUFSJOUIFUBOL5IFBWBJMBCMFTFUUJOHTBSF¡'¡'¡$BOE0GG0ODFBDDFTTFEQSFTTŻor Źto
choose the desired setting. Then press ~to set and exit.
Master Reset - resets the brewer universal control module (UCM) to the factory default settings. Once
accessed, “Are You Sure?” will appear on the display. Press Żfor Yes or Źfor No.
Service Call - sets the service phone number that appears on the display when the UCM detects a SENSOR
ERROR or WATER ERROR . Once accessed, press Żor Źto choose the number to be changed. Then press
~repeatedly to change the number value. Press Żor Źto choose the next number to change or choose exit
and press ~.
Access Code - sets the access code entered to access programming mode. The factory default is 1-2-3-4.
Once accessed, press Żor Źto choose the number to change. Then press ~repeatedly to change the
number value (the range is 1 to 4). Press Żor Źto choose the next number to change or choose exit and
press ~.
Banner Name - changes the company name that appears on the display. The factory default is Curtis. No
name appears when all blanks are entered. Once accessed, press Żor Źto choose the letter to change.
Then press ~repeatedly to change the number value. Press Żor Źto choose the next number to change or
choose ex and press ~to exit.
Warmer Auto-Off - (GEMS, GEMT, GEMSIF, GEMTIF models) adjusts the length of time that elapses before
the dispenser warmer shuts off automatically. This function takes priority over the quality timer. The factory
EFGBVMUTFUUJOHGPS(&.4*'(&.5*'JTIPVST'PS(&.4(&.5UIFEFGBVMUJTiEJTBCMFEw5IFTFUUJOHSBOHFJT
1 to 12 hours. Once accessed, press Żor Źto adjust the number of hours. Then press ~to set and exit.
P-Maintenance - turns on/off and adjusts the P-Maintenance (preventive maintenance) brew monitor.
The factory default setting is Off. When On, the UCM measures the number of gallons brewed before the
1.BJOUFOBODFSFNJOEFSBQQFBSTPOUIFEJTQMBZ5IFTFUUJOHSBOHFJTUPHBMMPOTMJUFST0ODF
accessed, press Żor Źto choose the desired setting, then, press ~to exit.
Beeper On/Off - turns the beeper that is heard each time a button is pressed on or off. The factory default
setting is On. Once accessed, press Żor Źto choose the desired setting. Then, press ~to exit.
Drip-out Mode - TFUTUIFESJQPVUNPEFUJNFS"GUFSXBUFSTUPQTnPXJOHJUBMMPXTBEEJUJPOBMUJNFGPSUIFDPGGFF
to drain from the brew basket before the brew basket lock releases. The factory default is 2 min. This feature
SFEVDFTUIFDIBODFUIBUUIFCSFXCBTLFUXJMMCFSFNPWFEUPPFBSMZ5IFTFUUJOHSBOHFJTUPNJOVUFT0ODF
accessed, press Żor Źto choose the desired setting, then, press ~to exit.
Warmers Default - (Gemini models) sets the warmer temperature. The factory default setting is MED. The
BWBJMBCMFTFUUJOHTBSF0GG)*()'¡$.&%'¡$PS-08'¡$0ODFBDDFTTFE
press Żor Źto choose the desired setting, then press ~. On twin brewers press Żor Źto choose the
desired setting for the second warmer, then press ~. Press ~to exit.
*Off option not available on GEMX series models.
(&.*'BOE(&.9POMZCBTFEPOBCSFXUFNQFSBUVSFPG¡'¡$
continued...
PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H

PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H
Non-Brew Programming Menu (cont.)
Display Brew Time - turns the display of the brew time during brewing On or Off. The factory default setting is
On. Once accessed, press Żor Źto choose the desired setting, then press ~to exit.
Display Messages - turns display of the message “Rinse Server Before Brewing” On or Off The factory default
setting is On. Once accessed, press Żor Źto choose the desired setting, then press ~to exit.
[QT] Display Timers [On/Off] - (some models, QT Alarm must be on) turns the quality timer countdown
display On or Off. The factory default setting is Off. Once accessed, press Żor Źto choose the desired
setting. Then, press ~to exit.
QT Alarm On/Off - (Gemini models) turns the quality timer audio alarm On or Off. The factory default setting
is On for GEMS/GEMT models, Off for GEMIF and GEMX models. An audible alarm goes off when the quality
timer has expired. Once accessed, press Żor Źto choose the desired setting. Then, press ~to exit.
Satellite Color - (GEMX series models only) changes the color scheme of the quality timer LEDs on the
dispenser (satellite). Once accessed, press Żor Źto choose the desired color to indicate “fresh” (On). Press
~to save, then press Żor Źto choose the desired color to indicate “expired”. Press ~to save and exit.
Server Lockout - (GEMX series models only) turns the lockout feature On or Off. The factory default setting
JT0GG8IFOTFUUP0OUIF#3&8CVUUPOJTEJTBCMFEXIFOUIFSFJTnVJEJOUIFEJTQFOTFSQSPWJEFEUIBUBO*3
equipped dispenser is in use (LOCKED appears on the display). Once accessed, press Żor Źto choose the
desired setting. Press ~to save and exit.
Brew Button Programming Menu
8IFOZPVmSTUFOUFSUIF#SFX#VUUPO1SPHSBNNJOHNFOVZPVXJMMCFBTLFEUPTFMFDUQSFTTB#3&8CVUUPOUP
DIBOHFUIFTFUUJOHTGPS5PQSPHSBNNPSFUIBOPOF#3&8CVUUPOmOJTIQSPHSBNNJOHUIFmSTUUIFOQSFTTŹuntil
Exit appears on the display. Press ~to exit, then re-enter the Brew Button Program to program the next one. The
default brew settings assume that the amber AFS spray head is installed.
Brew by Volume - BEKVTUTUIFWPMVNFCSFXFE5IFGBDUPSZEFGBVMUTFUUJOHTBSF-"3(&P[P[-
NM .&%*6.P[P[-NM 4."--P[P[-NM8JUIBEJTQFOTFSJO
place, press the BREW button that is illuminated. When the desired volume is reached, press the same BREW
button again to stop the brew cycle and set the volume.
* Not applicable to TP1 series.
** This is the LARGE setting for TP1 series brewers.
continued...
Select ~
Select ~
Select ~
Select ~
Select Button...
<-- Select -->
Press BREW
Brew Button Prog
<-- Select -->
Pulse Brew
<-- Select -->
Brew by Time
<-- Select -->
Press ~
Exit
<-- Select -->
Pre-Infusion
<-- Select -->
Pulse Brew
<-- Select -->
Brew by Volume
<-- Select -->
Bypass On/Off
<-- Select -->
Press ~

PROGRAMMING GUIDE PG2
8$130(3"..*/((6*%&ø H
Brew Button Programming Menu (cont.)
Brew by Time - adjusts the amount of coffee brewed by time rather than by volume. The factory default
TFUUJOHTBSF-"3(&NJOTFD.&%*6.NJOTFD4."--NJOTFD0ODFBDDFTTFEQSFTT
Żor ŹVOUJMUIFOVNCFSPGNJOVUFTJTnBTIJOH5IFOQSFTT~repeatedly to change the number value. Press
Żor ŹVOUJMUIFOVNCFSPGTFDPOETJTnBTIJOH5IFOQSFTT~repeatedly to change the number value. Press
Żor ŹVOUJMiFYwJTnBTIJOHUIFOQSFTT~to exit.
* Not applicable to TP1 series.
** This is the LARGE setting for TP1 series brewers.
Pre-Infusion - sets the brewer Pre-Infusion time (Pulse Brew must be off to access, the factory default setting is
%JTBCMFE1SF*OGVTJPOJODSFBTFTDPOUSPMPGDPGGFFDMBSJUZBOEFYUSBDUJPO8IFOUVSOFEPOUIFTFUUJOHSBOHFJTUP
TFDPOET0ODFBDDFTTFEQSFTTŻor Źto choose the desired setting, then, press ~to exit. To turn off pulse
CSFXNPEFDIPPTFGPSUIFUJNF
When Pre-infusion is On, Pulse Brew disappears from the list of menu items.
Pulse Brew - selects the pulse brew pattern (Pre-Infusion must be off to access, the factory default setting
JT$5IFQVMTFCSFXQBUUFSOTFMFDUFEiUVOFTwPSDIBOHFTUIFnBWPSPGUIFDPGGFF0ODFBDDFTTFEQSFTTŻor
Źto choose the desired setting. Then, press ~to exit.
8IFO1VMTF#SFXJT0O$PME#SFX-PDLJTTFUUPXJUIJO'¡$PGUIFXBUFSUFNQFSBUVSFMFWFMBOE
Cold Brew Lock and Pre-Infuson disappear from the list of program selections.
Pulse Brew Guidelines
• Filter pack type coffees typically extract better with the A and B pulse setting.
• Decaffeinated coffees typically extract better with the B pulse setting.
• High-yield coffees typically extract better with the C pulse setting. Of course, any of the A, B or C
TFUUJOHTNBZCFVTFEUPTVJUZPVSUBTUFQSPmMF
• Settings D and E are manual pulse counts.
By-Pass - IFMQTDPOUSPMFYUSBDUJPOXJUIMBSHFSCSFXT5IFGBDUPSZEFGBVMUTFUUJOHTBSF-"3(&GPS
51TFSJFT.&%*6.4."--0GG*USFEVDFTDPOUBDUUJNFUPBWPJEFYUSBDUJPOPGVOEFTJSBCMFCJUUFSBOE
IBSTInBWPSDPNQPVOET5IFTFUUJOHSBOHFJTUP0ODFBDDFTTFEQSFTTŻor Źto choose the
desired setting, then, press ~to exit.
Language Menu - changes the language that appears on the display. The factory default setting is English. This
feature is programmable for changing and adding languages. Once accessed, press Żor Źto choose the
desired setting, then press ~to exit.
continued...
Setting Description
A Toward the beginning of brew cycle: 4 cycles of 10 seconds on and 10 seconds off, then on until end of brew cycle.
BStarts towards ends of brew cycle. 4 cycles of 10 seconds off and 4 cycles of 10 seconds on. Ends when brew
cycle ends.
C Starts at beginning of brew cycle. 5 cycles of 25 seconds on and 20 seconds off, then on until end of brew cycle.
DManually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 20. Pulse on time and off
time are both adjustable from 5 to 150 seconds.
EManually set. Starts at beginning of brew cycle. Number of pulses is adjustable from 1 to 8. Pulse on time and off
time are both adjustable from 1 to 150 seconds.