CyberData 011404 Manual

Quick Reference 931238A © 2016, CyberData Corporation, ALL RIGHTS RESERVED© 2016, CyberData Corporation, ALL RIGHTS RESERVED 931238A Quick Reference
Connections
Mounting the Enclosure
Contacting CyberData
Primary Speaker Connection
Secondary Speaker Connection
Line-Out Connection
Line-In Connection
Relay Connection
Sensor Connection
To mount the enclosure:
1. Prepare holes for the screws.
2. Plug in the power adapter and use the
Power (PWR) LED to verify that the
power is on.
3. Plug the ethernet cable into the device.
The Link/Activity (Link/Act.) LED
verifies the network connection.
4. For wall mounting, use the three
#6 x 1-1/4-inch Pan Head Phillip screws
to secure the speaker.
071057A
PHILLIP SCREW (3x)
#6x1 1/4" PAN HEAD
#6 PLASTIC ANCHOR (3x)
151014
531032
Sales: [phone] ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: [phone] ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: [phone]
Fax: [phone]
http://www.cyberdata.net/
Getting Started
• Download the VoIP Loudspeaker Amplifier Operations Guide PDF file from the Documents tab at the following
webpage: http://www.cyberdata.net/voip/011404/
• Create a plan for the locations of your paging amplifiers.
• WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the
installation instructions.
• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
• WARNING: The VoIP Loudspeaker Amplifier enclosure is not rated for any AC voltages!
Wiring the 125V AC Plug
Parts
Parameter Factory Default Setting
IP Addressing DHCP
IP Addressa
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username admin
Web Access Password admin
Subnet Maska255.0.0.0
Default Gatewaya10.0.0.1
The green wire with the yellow stripe is a ground connection for electrostatic discharge (ESD) protection,
and should not be removed.
To wire the 125V AC plug, consult a licensed electrician and the local building codes in your area.
(1) Assembly (1) Wall Mounting Kit
(3) #6 Plastic Anchors (3) #6 x 1-1/4-inch Pan Head Phillip Screws
(1) Enclosure
(1) CAT 5e/CAT6 cable
Additional Parts
(1) PoE Power Injector
Installation Quick Reference
VoIP Loudspeaker Amplifier
(AC-Powered)
SIP Compliant
011404
The IP Endpoint Company
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

© 2016, CyberData Corporation, ALL RIGHTS RESERVED 931238A Quick Reference Quick Reference 931238A © 2016, CyberData Corporation, ALL RIGHTS RESERVED
7.938
[201.63]
6.281 [159.54]
Dimensions are in Inches [Millimeters]
Features
Connections Behind the Port Cover
SPD Link/Act.
PWR Status
Volume
RTFM
VoIP
Loudspeaker
Speaker Volume
Speed (SPD) LED (AMBER)
The Speed (SPD) LED illuminates AMBER for a 100Mb link
or is off for a 10MB link when the network link to the device is established.
Status LED (GREEN)
The GREEN Status LED illuminates after supplying power to the device.
Link/Activity (Link/Act.) LED (GREEN)
The GREEN Link/Activity (Link/Act.) LED blinks to indicate network traffic.
Power (PWR) LED (GREEN/BLUE)
The Power (PWR) LED is GREEN in low power mode (802.3af)
and BLUE during high power mode (802.3at).
RTFM Switch
To broadcast the device’s current IP address, press and hold the RTFM switch for a couple
of seconds and then release it.
To restore the factory defaults, complete the following steps:
1. Press and hold the RTFM switch until you hear the device announce the words,
“restoring defaults” and “rebooting”.
2. Release the RTFM switch. The device will be restored to the factory default settings.
*See the Operations Guide for more information about the features in this section.
Strobe CLK - 5
Strobe Data - 4
GND- 3
Strobe Power - 2
GND - 1
Chassis Gnd - 3
Mic In - 2
GND - 1
CLASS II WIRING
Dimensions and Mounting Template
14.500
[368.30]
10.875 [276.23]
4.375
[111.13]
Cable Grommets (3 PLCS)
Dimensions are in Inches [Millimeters]
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]