Cybertek CTB20B User manual

Shenzhen Zhiyong Electronics Co., Ltd.
www.cybertek.cn
AC/DC High Accuracy Current Probe
CTB20B (20A/1MHz)
CTB200B (200A/500kHz)
CTB500B (500A/100kHz)
CTB1000B (1000A/20kHz)
Shenzhen Zhiyong Electronics Co., Ltd.
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
1
Preface
First of all, thank you for purchasing our products, this instruction manual is the
description about the function, usage, operation attention points, etc. Before use, please
read the instructions carefully and use correctly.
Manual annotation will use the following symbols to distinguish.
To the safely use the machine, you must abide by the following safety precautions strictly.
The violation against the manual is likely to damage the protective function of the
machine. In addition, the company is not responsible for any safety problem caused by the
violation of matters needing attention in operation.

Please avoid direct contact with the naked conductor, or there will be shortage or shock accident.

Please measure on the insulated wire that has proper insulation from the circuit voltage.

Shock accident will possibly occur if the device or the user’s hand is wet, please watch out.

The maximum measurable current will change according to the frequency. As the treatment to lower
the rated value, maximum continuous measurable current will be limited. Please do not measure the
current with lower amplitude surpassing rated value. The malfunction caused by sensor heating will
possibly cause fire accident and burn.
Warn
Notice
Warn
In the case of wrong operation, the user risk injury. The content under this
mark records the relevant matters needing attention to avoid such dangers.
The user may suffer minor injuries and material damage with the wrong
operation. To avoid such situation, the matters under this mark need attention.
This symbol means it is harmful to the machine and human body; you must
strictly follow the instruction manual to operate.
Note
This symbolizes important note about how to use the machine.
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
2
 Do not use the top part of the clamp to fix the foreign matter. This could possibly lower the
performance of the sensor characteristics or malfunction the switch.
 Do not input current to the device when the power supply is cut off, or the device will possibly be
damaged.
 Please do not step on or clamp on the wire to protect its skin.
 Do not touch the core part when the clamp is opened. Static electricity on the core could possibly
damage the device.
 Please remain the clamp close in spare time. The dust on the clamp contact surface could case the
measurement error.
 Please undo the lock before pulling out the input connector, or the connector will be damage by force.
 The cable will be hardened in the environment below 0℃. The cable skin or even cable itself will be
damaged if cable is forced to bow or pulled.
 Please avoid vibration or impact when the device is in operation or transportation, especially the falling
impact.
 Please avoid the operation under sunny, thermal, damp and humid environment. Deformation and
worsen insulation will ruin the operation specification.
 Please check the device before usage to make sure the device is not malfunctioned caused by storage
and transportation. Please contact the commission agent or operator nearby when malfunction is
observed.
 The device is not designed neither waterproof nor dust-proof. Do not use the device under dusty and
complex chemical environment.
 Do not use the device in the strong EM wave environment or close to the electrified object.
 Do not use the device near any sort of induction heating device. (e.g. Induction cooker)
Warn
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
3
Index
Preface………………………………………………………………………………………………….……1
Summary……………………………………………………………………………………………….……4
Application……………………………………………………………………………………………….……4
Product Description……………………………………………………………………………………….…4
Option Device………………………………………………………………………………………….…5
Product Electronic Specification…………………………………………………………………….……5
Machinery Specification……………………………………………………………………………..……..…9
Environment Characteristics…………………………………………………………………….…….…......9
Operating Methods…………………………………………………………………………….…….……..…9
Note During Operation………………………………………………………………. ….…………..…….9
Measurement Steps……………………………………………………………………………….....…….10
Packing List………………………………………………………………………………….……….….…11
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
4
1. Summary
CTB series current probe is a kind of current probe which can measure DC and AC at the same time. It
is a clamp type current sensor which can be opened / closed for AC / DC current measure. Its characteristics
include: high precision, typical value 0.3%; good frequency and temperature characteristics; high bandwidth.
CTBxxxA need to cooperate with CTB104 (Four channel sensor unit) in operation, while CTBxxxB series
is powered by 12V adaptor. With the power analyzer, it can realize power analyze in the high accuracy
current measurement.
2. Application

Power supply (Switch type and linear type) design
 Neo energy, electric vehicle design

Variable frequency household appliance
 Electric industrial experiment

Inverter/transformer design
 Electronic Ballast

Industrial/consumer electronics design
 Engine drive design

Power electronics and electrical drive experiment
 Traffic transport system (Electric mobile, locomotive, avionic device) design
3. Product Description
Take CTB500B/1000B as example:
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
5
1Jaw:CTB20B/CTB200Bdiameter 20mm,CTB500B/CTB1000B diameter 50mm.
2Power indicator: lighted green indicates power on.
3Degaussing indicator: lighted red when degaussing button was pressed. After the degaussing, indicator
will be off.
4Handle auto degaussing button: After frequent usages, the residual field on the probe will influence
the accuracy of the device. Press the button to degauss before the next measurement to improve the
performance.
5Offset adjust button(increase): press to increase offset. Pressing over 2s will continuously increase the
output offset.
6Offset adjust button(decrease): press to decrease offset. Pressing over 2s will continuously decrease
the output offset.
7Power supply wire: Power supply wire connecting with 12V adaptor.
8Output wire: Signal output port connecting test equipment.
9Distribution box auto degaussing button: perform same function as handle degaussing button, Press
the button to degauss before the next measurement to improve the performance.
10 Current direction mark: Current direction should be the same as the mark, or the output will be
negative.
11 Open/Close handle: Control the jaw through this handle
12 Lock push rod: Control the lock and unlock of the jaw.
4. Accessories
Power supply adaptor(CK-612)
5. Product Electronic Specification
f.s. Maximum display value or scale length (symbolizing the rated primary current range)
rdg. Reading value (symbolizing the current value under measurement, or the current value indicated
by the measurement devices)
Proceed measurement under condition of sin wave input, central conductor position and powered by
12V adaptor.
Measuring device of input resistance over 1MΩ
Please correctly degauss zero set before the measurement.
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
6
CTB20B
CTB200B
CTB500B
CTB1000B
Rated current
AC/DC 20A
AC/DC 200A
AC/DC 500A
AC/DC 1000A
Bandwidth
1MHz
500kHz
100kHz
20kHz
Current transfer ratio
100mV/A
10mV/A
4mV/A
2mV/A
Maximum input
current
Refer to the Current rated value vs. Frequency curve
Accuracy
Refer to the Accuracy List
Operating temperature
and humidity range
-40℃~85℃, Below 80%RH (No dew)
Promised accuracy
range
0℃~40℃, Below 80%RH
Temperature drift
coefficient
-40℃~0℃﹑40℃~85℃
Amplitude Sensitivity: Below±0.02% rdg./℃
Offset Voltage:≤±0.01% f.s./℃
Diameter of
measurable conductor
Φ Below 20 mm
Φ Below 50 mm
Conductor position
effect
Below ±0.1% rdg.
(Input 20A,
DC-100Hz, outer
diameter 5mm)
Below ±0.1% rdg.
(Input 100A,
DC-100Hz, outer
diameter 5mm)
Below ±0.2% rdg.
(Input 100A,
DC-100Hz, outer
diameter 10mm)
Below ±0.2% rdg.
(Input 1000A,
50Hz/60Hz, outer
diameter 30mm)
Power supply method
DC 12V/1A (standard adaptor)
CTB20B Accuracy List
Frequency
Amplitude
Phase
DC
±0.3% rdg. ±0.05% f.s.
-
DC < f ≤ 100 Hz
±0.3% rdg. ±0.01% f.s.
±0.1deg.
100Hz< f ≤ 500 Hz
±0.3% rdg. ±0.02% f.s.
±0.2deg.
500Hz< f ≤ 1kHz
±0.5% rdg. ±0.02% f.s.
±0.5deg.
1kHz< f ≤ 5kHz
±1.0% rdg. ±0.02% f.s.
±1.0deg.
5kHz< f ≤ 10kHz
±1.5% rdg. ±0.02% f.s.
±1.5deg.
10kHz< f ≤ 50kHz
±2.0% rdg. ±0.02% f.s.
±(0.5+0.1×f
kHz)deg.
50kHz< f ≤ 100kHz
±5.0% rdg. ±0.05% f.s.
100kHz< f ≤ 300kHz
±10% rdg. ±0.05% f.s.
300kHz< f ≤ 500kHz
±15% rdg. ±0.05% f.s.
-
500kHz< f ≤ 1MHz
±30% rdg. ±0.05% f.s.
-
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
7
CTB200B Accuracy List
Frequency
Amplitude
Phase
DC
±0.3% rdg. ±0.02% f.s.
-
DC < f ≤ 100 Hz
±0.3% rdg. ±0.01% f.s.
±0.1deg.
100Hz< f ≤ 500 Hz
±0.3% rdg. ±0.02% f.s.
±0.2deg.
500Hz< f ≤ 1kHz
±0.5% rdg. ±0.02% f.s.
±0.5deg.
1kHz< f ≤ 5kHz
±1.0% rdg. ±0.02% f.s.
±1.0deg.
5kHz< f ≤ 10kHz
±1.5% rdg. ±0.02% f.s.
±1.5deg.
10kHz< f ≤ 50kHz
±5.0% rdg. ±0.02% f.s.
±(0.5+0.1×f
kHz)deg.
50kHz< f ≤ 100kHz
±15% rdg. ±0.05% f.s.
100kHz< f ≤ 300kHz
±15% rdg. ±0.05% f.s.
300kHz< f ≤ 500kHz
±30% rdg. ±0.05% f.s.
-
CTB500B Accuracy List
Frequency
Amplitude
Phase
DC
±0.3% rdg. ±0.02% f.s.
-
DC < f ≤ 100 Hz
±0.3% rdg. ±0.01% f.s.
±0.1deg.
100Hz< f ≤ 500 Hz
±0.3% rdg. ±0.02% f.s.
±0.2deg.
500Hz< f ≤ 1kHz
±0.5% rdg. ±0.02% f.s.
±0.5deg.
1kHz< f ≤ 5kHz
±1% rdg. ±0.02% f.s.
±1.5deg.
5kHz< f ≤ 10kHz
±1.5% rdg. ±0.02% f.s.
±2.0deg.
10kHz< f ≤ 20kHz
±5% rdg. ±0.02% f.s.
±(0.2×f kHz)deg.
20kHz< f ≤ 50kHz
±10% rdg. ±0.05% f.s.
50kHz< f ≤ 100kHz
±30% rdg. ±0.05% f.s.
CTB1000B Accuracy List
Frequency
Amplitude
Phase
DC
±0.3% rdg. ±0.02% f.s.
-
DC < f ≤ 100 Hz
±0.3% rdg. ±0.01% f.s.
±0.1deg.
100Hz< f ≤ 500 Hz
±0.5% rdg. ±0.02% f.s.
±0.2deg.
500Hz< f ≤ 1kHz
±1% rdg. ±0.02% f.s.
±0.5deg.
1kHz< f ≤ 5kHz
±2% rdg. ±0.02% f.s.
±1.5deg.
5kHz< f ≤ 10kHz
±5% rdg. ±0.05% f.s.
±2.0deg.
10kHz< f ≤ 20kHz
±30% rdg. ±0.1% f.s.
±10.0deg.
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
8
CTB20B
Current rated value vs. Frequency curve
TA: ambient temperature
CTB200B
Current rated value vs. Frequency curve
TA: ambient temperature
CTB500B
Current rated value vs. Frequency curve
CYBERTEK

Shenzhen Zhiyong Electronics Co., Ltd.
9
CTB1000B
Current rated value vs. Frequency curve
6. Machinery Specification
CTB20B
CTB200B
CTB500B
CTB1000B
Jaw diameter
20mm
50mm
Connecting cable length
3m
Current clamp handle
dimension（L*W*H）
162*80*31mm
246*116*35mm
Probe weight
385g
750g
880g
7. Environment Characteristics
Operation environment
Indoor, pollution level 2
Operation temperature and humidity
-40℃~85℃,below 80% RH(no dew)
Storage temperature and humidity
-40℃~85℃,below 80% RH(no dew)
Operation altitude
2000m
Storage altitude
12000m
8. Operation Methods
Note During Operation
 The device is powered by 12V adaptor in measurement. Please select the high input resistance (1MΩ)
when output to the oscilloscope. If the input resistance is 50Ω, the measurement will be error.
 Make sure the current under test is below the maximum value. The magnetic core will be saturated if
rated value is surpassed. As the result the waveform generated will be partially cut off and the surge
current will cause failure on core degaussing process, need to be adjust again to zero set.

If there’s high magnetic field (e.g. transformer, large circuit) or strong current (e.g. wireless) near the
Note
CYBERTEK