CYP OR-42-4K22 User manual

OR-42-4K22
4 x 2 HDMI Matrix Switcher (4K, HDCP2.2, HDMI2.0)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 28/10/2016 First release

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions .......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 Remote Control........................................10
6.4 WebGUI .......................................................11
6.4.1 WebGUI Control Page...................12
6.4.2 Power On/O ..................................12
6.4.3 Routing..............................................13
6.4.4 Source Detect .................................13
6.4.5 Status..................................................14
6.4.6 EDID....................................................14
6.4.7 HDCP Control ..................................15
6.4.8 Firmware Update ...........................16
6.4.9 HDMI Out Info.................................16
6.4.10 Labelling.........................................17
6.4.11 Network Setting...........................17
6.5 Telnet Control ...........................................17
6.6 RS-232 Command....................................20
7. Connection Diagram .......................... 22
8. Specications...................................... 23
8.1 Technical Specications ........................23
8.2 Support Timing Table.............................24
8.3 HDMI Cable Length.................................25

6
1. INTRODUCTION
This 4x2 HDMI Matrix Switcher is designed to enable the user to switch
between any of the four connected HDMI sources to send video and
audio to either of the two connected HDMI displays. This matrix switcher
fully supports 4K resolutions and is HDMI2.0 and HDCP 2.2 compliant,
ensuring maximum compatibility with the latest 4K UHD sources and
displays.
The unit supports all the latest features of the HDMI2.0 specication
such as 4K UHD resolutions (4K2K@60Hz - YUV4:4:4),HDR (High Dynamic
Range), 'Deep Color', and High Denition audio. Control is via manual
selection buttons, IR, RS-232, Telnet or Web GUI.
2. APPLICATIONS
Entertainment Room & Home Theater
Show Room & Demo Room
Class room & Lecture Hall Presentations
Public Commercial Display
3. PACKAGE CONTENTS
1 x HDMI matrix unit
1 x IR Extender with cable
1 x 5V / 2.6A DC power adaptor
1 x Remote control unit (model: CR-155)
1 x Operation Manual
4. SYSTEM REQUIREMENTS
HDMI source equipment such as media players, video game consoles
or set-top boxes.
HDMI receiving equipment such as HDTVs, monitors or audio
ampliers.
The use of“Premium High Speed HDMI” cables is highly recommended.

7
5. FEATURES
HDMI2.0 and HDCP2.2 compliant
Routes four HDMI sources to two HDMI displays
Supports pass-through of HD audio formats: LPCM 2/5.1/7.1CH, Dolby
Digital 2/5.1CH, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos and
DTS-HD Master Audio
4K UHD resolutions (4K2K@60Hz - YUV4:4:4)
Supports HDR (High Dynamic Range) and Deep Colour

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWERA
A
1
2
3
4
1
2
3
4
B
BH
DMI IN
HDMI IN / OUT
1
1 2 3 4 5 6
1IR window: Accepts IR signals from the included IR remote for control
of this unit only.
2POWER: Press this button to power on the unit or place it into stand-
by mode.
Note: Ethernet and RS-232 remain active while the unit is in stand-by
mode.
3Power indicator: This LED will illuminate GREEN to indicate the unit
is on and receiving power. When the unit is in stand-by mode the LED
will illuminate RED.
4HDMI Out routing buttons“A” & “B”: Press either of these buttons
to sequentially switch through the available inputs for the associated
output.
5HDMI In indicator “1&2&3&4”: The LED in each column will
illuminate GREEN to indicate which source is currently selected for
each output
6HDMI In: Connect to HDMI source equipment such as a media player,
game console or set-top box. DVI sources are also supported with the
use of an HDMI to DVI adapter.

9
6.2 Rear Panel
234AB
HDMI IN HDMI OUT SERVICE CONTROL RS-232 IR IN DC 5V
1 2 3 4 5 6 7
1HDMI In : Connect to HDMI source equipment such as a media player,
game console or set-top box. DVI sources are also supported with the
use of an HDMI to DVI adapter
2HDMI Out: Connect to HDMI TVs, monitors or ampliers for digital
video and audio output. DVI sources are also supported with the use
of an HDMI to DVI adapter
3SERVICE: This slot (USB 2.0) is reserved for rmware update use only.
Please plug in a USB thumb drive containing the new rmware to
update the unit.
4CONTROL: Connect directly, or through a network switch, to your PC/
laptop to control the unit via telnet/WebGUI.
5RS-232: Connect directly to your PC/laptop to send RS-232 commands
to control the unit.
6IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
7DC 5V: Plug the 5V DC power adapter into the unit and connect it to
an AC wall outlet for power.

10
6.3 Remote Control
1POWER: Press Power key to turn on the
device or set to standby mode.
2OUTPUT A1~A4 & B1~B4:Press these
buttons to change the routing of output A/B.
CR-155
POWER
1
2
3
4
1
2
3
4
BA
1
2

11
6.4 WebGUI
Install the IP Discovery Tool:
1. Please obtain the Device Discovery software from your authorized
dealer or download it from our website and save it in a directory
where you can easily nd it.
Note: The unit’s default IP address is 192.168.1.50
2. Connect the unit and your PC/Laptop to the same active network
and execute the Device Discovery software. Click on “Find Devices
on Network” and a list of devices connected to the local network will
show up indicating their current IP address.
3. By clicking on one of the listed devices you will be presented with the
network details of that particular device. If you choose, you can alter
the static IP network settings for the device, or switch the unit into
DHCP mode to automatically obtain proper network settings from a
local DHCP server. To switch to DHCP mode, please select DHCP from
the IP mode drop-down, then click “Save” followed by “Reboot”.
Once you are satised with the network settings, you may use them to
connect via telnet or WebGUI. The network information window provides
a convenient link to launch the WebGUI directly.

12
6.4.1 WebGUI Control Page
All functions, including power, input selection, EDID management,
HDCP management, Ethernet settings, and reset/rmware functions,
are presented on a single web page to allow for intuitive operation. The
individual functions will be introduced in the following sections.
6.4.2 Power On/O
The unit can be powered on or o (stand-by mode) from this tab.

13
6.4.3 Routing
This tab allows for the selection of the input source for each output. Four
HDMI inputs and two HDMI outputs are available for selection.
6.4.4 Source Detect
When a live input source is one of the 4 HDMI inputs the corresponding
input in this tab will display “ON”. If no source is detected on that input, it
will display “OFF”.

6.4.5 Status
This tab displays the currently selected HDMI input sources for each
output and the unit’s rmware version. It also provides a way to reset or
reboot the unit.
1) To perform a factory reset on the unit, please click the“RESET” button.
2)To reboot the unit, please click the“REBOOT” button.
6.4.6 EDID
This tab controls EDID management for the unit. All inputs can share the
same assigned EDID, or each input can have a discrete EDID assigned to it.
1) Selecting the “ALL” mode will send the selected EDID to all inputs.
2) Selecting the “APPOINT” mode allows each input to have a dierent
EDID assigned to it.
3) The available EDID options include SINK A/SINK B (EDID is passed
from one of the currently connected displays), 8/2D/PCM/720p, 8/2D/
PCM/1080p, 8/2D/PCM2/4K 3G, 8/2D/PCM2/4K Y420 and 8/2D/PCM/4K
6G.

6.4.7 HDCP Control
This tab allows for the HDCP mode to be switched between “Standard”
and “Apple”mode. “Apple” mode allows for the display of non-HDCP
required content from Apple devices on non-HDCP displays. This setting
can be assigned individually to each input.

16
6.4.8 Firmware Update
This tab provides a way to update the rmware of the unit.
1) BROWSE: Click the “BROWSE” button to select the rmware update .bin
le which is located on your local PC.
2) UPDATE: Click the “UPDATE”button to begin the rmware update
process.
6.4.9 HDMI Out A Info & HDMI Out B Info
These tabs present the information detected from displays connected
to HDMI outputs A & B, including type, manufacturer name, native
resolution, color depth, 3D support, 4K support and audio format support.

17
6.4.10 Labelling
This tab allows for the labelling of the four HDMI input ports and the two
HDMI output ports. Please click the“SAVE” button to store the changes.
6.4.11 Network Setting
This tab provides control over the unit’s network settings. The IP mode
can be set to DHCP for automatic IP conguration, if your local network
supports it, or it can be placed into STATIC mode. When in STATIC mode
the IP address, netmask and gateway can be dened manually. The HTTP
and telnet ports can also be changed from their defaults here.

18
6.5 Telnet Control
Before attempting to use telnet control, please ensure that both the unit
and the PC/Laptop are connected to the same active networks.
To access Telnet in Windows 7, click on the“Start” menu and type “cmd” in
the search eld, then press “Enter”.
Under Windows XP go to the “Start” menu, click on “Run”, type “cmd” then
press “Enter”.
Under Mac OS X, go to Go→Applications→Utilities→Terminal
See below for reference.
Once in the CLI (Command Line Interface) type “telnet” followed by the IP
address of the unit and “23”, then hit “Enter”.

19
This will connect us to the unit we wish to control. Type “help”to list the
available commands.

20
6.6 RS-232 Command
Command Description Parameter
HELP/?List available commands NONE
P0 POWER OFF NONE
P1 POWER ON NONE
INNAME SET/SHOW ALL INPUT NAMEIN NAME [1~4] [8 char]
OUTNAME SET/SHOW HDMI OUTPUT
NAME
OUTNAME [A/B] [8 char]
ASET/SHOW OUTA SOURCE A [1~4]
BSET/SHOW OUTB SOURCE B [1~4]
OUT SET/SHOW OUTA/B SOURCE OUT [1~4]
SOURCEDET SHOW INPUT INFORMATION NONE
SINKINFO SHOW OUTPUT INFORMATION NONE
HDCPIN SET/SHOW INPUT HDCP
STATUS
HDCPIN [1~4]
[0:STANDARD/1:APPLE]
EDIDMODE SET/SHOW EDID MODE TYPE EDIDMODE
[0:APPOINT/1:ALL]
EDIDALL SET/SHOW EDID ALL CONTENT EDIDALL [0~6]
0=OUTPUT A
1=OUTPUT B
2=8/2D/PCM/720P
3=8/2D/PCM/1080P
4=8/2D/PCM/4K2K_30
5=8/2D/PCM/4K2K_Y420
6=8/2D/PCM/4K2K_60
EDIDIN SET/SHOW EDID INPUT
CONTENT
EDIDIN [1~4] [0~6]
FADEFAULT SET ALL CONFIGURATIONS TO
FACTORY DEFAULT
NONE
REBOOT REBOOT DEVICE NONE
VER DISPLAY FIRMWARE VERSION NONE