CYP CPLUS-V8H8HP User manual

CPLUS-V8H8HP
4K UHD+8×8 HDMI Matrix
with USB Power Outputs
Operation Manual
Operation Manual

DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2017 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
RDV1 19/09/17 Preliminary release
VS1 20/12/17 Final technical review
VS2 16/01/18 Additional input selection modes
& Updated resolution support list

CONTENTS
1. Introduction......................................................1
2. Applications.....................................................1
3. Package Contents ..........................................1
4. System Requirements......................................2
5. Features............................................................2
6. Operation Controls and Functions.................3
6.1 Front Panel ................................................. 3
6.2 Rear Panel.................................................. 4
6.3 Remote Control......................................... 5
6.4 LCD Menu .................................................. 6
6.5 IR Cable Pin Assignments ......................... 7
6.6 RS-232 Protocol.......................................... 7
6.7 Telnet Control ............................................ 8
6.8 RS-232 and Telnet Commands ................ 9
6.9 WebGUI Control ...................................... 22
7. Connection Diagram ....................................34
8. Specications ................................................35
8.1 Technical Specications ........................ 35
8.2 Video Specications............................... 36
9. Acronyms .......................................................37

1
1. INTRODUCTION
This 8 by 8 Matrix provides the ability to connect up to eight 4K
UHD HDMI sources to up to eight 4K UHD HDMI displays and freely
switch between them. This unit comes with full support for 18Gbps
(600Mhz) resolutions up to, and including 4K@60Hz (4:4:4, 8-bit) as
well as support for 16-bit Deep Color up to 1080p@60Hz, HDR (High
Dynamic Range), HD audio and other features dened by the HDMI
2.0a specication. With a comprehensive EDID management feature
that includes the ability to select between built in default EDID, EDID
copied from connected sink devices, as well as a congurable EDID,
this matrix can solve many interconnectivity problems.
This unit also features eight USB ports which supply up to 5V/1A power
for use with connected AOC (Active Optical Cable) ber cable
extenders. By using these specialized cables your HDMI content
can be extended much further than would be possible with normal
HDMI cables. The built-in OSD has the ability to display user editable
general information text so each output can display up to 2 lines of
customized text on top of the video source in the color of your choice.
This unit provides an intuitive set of front panel controls with an LCD as
well as RS-232, Telnet, WebGUI, and IR remote control options.
2. APPLICATIONS
• Smart Home Control
• Control Center
• Function Room
• Product Showroom
• Ballroom
3. PACKAGE CONTENTS
• 1×8 by 8 HDMI Matrix with USB Power Outputs
• 1×24V/6.25A DC Power Adapter
• 1×Power Cord
• 1×IR Extender Cable
• 1×Remote Control (CR-177)
• 1×Rack Mount Ears (Set of 2)

2
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as media players, video game
consoles or set-top boxes.
• HDMI receiving equipment such as HDTVs, monitors or audio
ampliers.
• The use of “Premium High Speed HDMI” cables is highly
recommended.
5. FEATURES
• HDMI 2.0a and DVI 1.0 compliant
• HDCP 1.x and 2.2 compliant
• Eight HDMI inputs matrixed to eight HDMI outputs with 18Gbps
(600MHz) 4K UHD support
• Supports HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &
4096×2160@60Hz (4:4:4, 8-bit)
• Supports 16-bit Deep Color up to 1080p@60Hz
• Supports pass-through of audio formats including LPCM 2.0/5.1/7.1,
Bitstream, and HD Bitstream
• Supports six internal EDIDs, eight external EDIDs copied from
connected devices, and four user provided EDIDs
• Eight USB ports to supply 5V/1A power to AOC (Active Optical
Cable) ber extension cables
• OSD with user customizable information text
• Controllable via front-panel buttons with LCD, WebGUI, Telnet, RS-
232, and IR remote

3
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
8x8 4K UHD+ Matrix IN 1 IN 2 IN 3 IN 4
OUT A OUT B OUT C OUT D CANCEL
IN 5
OUT E
IN 6
OUT F
IN 7
OUT G
IN 8
OUT H
CONFIRM ENTER
MENU
PRESET
ALL LOCK
+
-
MUTE
+
1 2 3
5 7 9 11
4 6 8 10 12 13
1POWER: Press this button to power the unit on (green LED) or place
it into stand-by mode (red LED).
2IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
3IN 1~8 & OUT A~H: Press these buttons to congure the video
routing. Behavior depends on the selected Keypad Action Mode.
3a In Standard Mode: Press the “OUT” buttons (A~H) of the outputs
you wish to route a source to (the letters will ash in the LCD to
indicate selection). Next, press the “IN” button of the input (1~8)
you wish to route to the selected outputs. Finally, press “CONFIRM”
to conrm your selection and execute the routing change.
3b In User Mode: Press the “OUT” button (A~H) of an output you wish
to route a source to (the letter will ash in the LCD to indicate
selection). Next, press the “IN” button of the input (1~8) you wish
to route to the selected output. Repeat this process as many times
as needed to select all new routes. Finally, press “CONFIRM” to
conrm your selections and execute the routing changes.
4CONFIRM: Press this button to conrm newly made input/output
routing selections.
5CANCEL: Press this button to cancel newly made input/output
routing selections before they have been conrmed.
6ENTER: Press to conrm a selection within the LCD menu or to go
deeper into a menu item.
7MENU: Press to enter the LCD menu, or to back out from menu
items.
8 PLUS (+) & MINUS (−): Press to move up and down or adjust
selections within menus.

4
9ALL: Press this button to select all outputs simultaneously for routing.
Next, press the “IN” key of the input (1~8) you wish to route to all
outputs. Finally, press “CONFIRM” to conrm your selection and
execute the routing change.
10 PRESET: Press to enter the preset recall menu in the LCD window.
Press the “+/-” buttons followed by the “ENTER” button to select
and activate the preferred preset.
11 LOCK: Press to lock all button functions on the front panel. Press
and hold for 3 seconds to release the lock function. The LCD will
display “Lock” when the function is active.
12 MUTE: The “MUTE” button functions as a blank audio/video source.
To use it, follow the standard matrix routing instructions, but use
the “MUTE” button as the input to blank out the selected outputs.
When a “MUTE” input is in use it will show up as “M” within the
routing display.
13 LCD WINDOW: Displays the unit’s menu, settings and information.
6.2 Rear Panel
12345678
HDMI IN ABCDEFGH HDMI OUT
USB 5V/1A OUT
12345678
CONTROL RS232 SERVICE DC 24V
IR IN
1 2
3 6
54 7 8
1HDMI IN 1~8: Connect to HDMI source equipment such as media
players, game consoles or set-top boxes.
2HDMI OUT A~H: Connect the HDMI outputs to devices such as
HDMI TVs, monitors or ampliers for digital video and audio output.
3USB POWER OUTPUT 1~ 8: Each USB port provides 5V/1A of power
intended for use with HDMI over AOC (Active Optical Cables)
ber optic video extension cables. Power on each port may be
individually enabled/disabled.
Note: If a USB device requiring more than 1A is connected, the
port will automatically shut off to prevent an overload and the red
LED will turn on.
4IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct

5
line-of-sight of the IR Extender.
5CONTROL: Connect directly, or through a network switch, to your
PC/laptop to control the unit via Telnet/WebGUI.
6RS-232: Connect directly to a PC, laptop or other serial control
device to send RS-232 commands to control the unit.
7SERVICE: This slot is reserved for rmware update use only.
8DC 24V: Plug the 24V DC power adapter into the unit and connect
it to an AC wall outlet for power.
6.3 Remote Control
1POWER: Press to power the unit on or place
it into stand-by mode.
21/A ~ 8/H: Press these keys to congure the
video routing. Behavior depends on the
selected Keypad Action Mode.
2a In Standard Mode: Press the “OUT” key
followed by the keys (A~H) of the outputs
you wish to route to. Next, press the “IN”
key followed by the input (1~8) you wish to
route to the selected outputs. Finally, press
“ENTER” to conrm your selection.
2b In User Mode: Press the “OUT” key followed by the key (A~H) of the
output you wish to route to. Next, press the “IN” key followed by
the input (1~8) you wish to route to the selected output. Repeat
this process as many times as needed. Finally, press “ENTER” to
conrm your selection.
3INFO: Switches the information displayed on each output’s OSD
between the user customized text and the current video/Ethernet
details.
4MUTE: The “MUTE” button functions as a blank audio/video source.
To use it, follow the standard matrix routing instructions, but use the
“MUTE” button as the input to blank out the selected outputs.
5PRESET: Press to enter the preset call menu in the LCD window.
Press the “+/-” buttons followed by the “ENTER” button to select
and activate the preferred preset.
6ALL: Press this key to select all outputs simultaneously for routing.
PRESET
ALL
INFO
MUTE
- /
OUT
+ /
IN
ENTER
CANCELMENU
CR-177
1 / A
2 / B
3 / C
4 / D8/ H
5 / E
6 / F
7 / G
1
2
8
9
3
4
5
6
7