CYP PUV-1210PL-RX User manual

PUV-662PL-4K22
6 x 8 HDMI HDBaseT™ LITE Matrix with Audio Matricing
(4K, HDCP2.2, HDMI2.0, PoH, OAR, 60m)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 03/03/2017 First release
v1.01 13/03/2017 Updated text and diagrams
v1.02 14/03/2017 Corrections to Specications
v1.03 23/03/2017 Minor Corrections

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................7
4. System Requirements ...........................7
5. Features..................................................8
6. Operation Controls and Functions .......9
6.1 Front Panel................................................... 9
6.2 Rear Panel...................................................10
6.3 Side Panel ...................................................12
6.4 Remote Control........................................13
6.5 OLED Menu................................................14
6.6 IR Cable Pin Assignment .......................15
6.7 RS-232 Protocol........................................15
6.8 RS-232 and Telnet Commands............16
6.9 Telnet Control............................................35
6.10 WebGUI Control.....................................37
7. Connection Diagram .......................... 56
8. Specications...................................... 57
8.1 Technical Specications ........................57
8.2 Video Specications................................58
8.3 Audio Specications...............................59
8.4 Category Cable Specications............61
8.5 HDBaseT Features....................................61
9. Acronyms............................................. 62

6
1. INTRODUCTION
This 6×8 HDMI and HDBaseT Matrix supports routing and transmission
of video (resolutions up to 4K@60Hz w/ HDMI 2.0 & HDCP 2.2) and audio
(multi-channel digital/stereo analogue) while providing flexible control
via IR, RS-232, Telnet or WebGUI. As many as six UltraHD sources may be
routed to any of eight destinations, six via single Cat.5e/6/7 cables (up to
60m at 1080p or up to 35m at 4K@30Hz) and two via HDMI 2.0 outputs.
The two HDMI 2.0 outputs support transmission of 18Gbps UltraHD
HDMI sources (up to 4K@60Hz, 4:4:4) from any HDMI input or they can
mirror any of the HDBaseT outputs for local monitoring. 3D video is also
supported when compatible sources and displays are connected.
This product supports passing 7.1 channel LPCM digital audio as well as
advanced bitstream and HD bitstream audio formats. Additionally, six
analogue audio outputs are available to provide stereo breakout audio
from the associated HDBaseT output (LPCM 2.0 sources only). Beyond
basic video routing, this product also incorporates an independent audio
matrix with eight audio outputs and four audio inputs. Oering discrete
audio routing, insertion and extraction, this product makes it possible to
have multiple audio zones within your installation. This product supports
the Optical Audio Return (OAR) channel feature, found on compatible
HDBaseT receivers, allowing optical audio sources connected to those
receivers to be sent back to the matrix unit.
Internally generated test patterns (up to 18Gbps UHD resolutions) are
provided to assist with setup, providing a simple way to verify both matrix
and sink functionality. The Power over HDBaseT (PoH) function can power
compatible receivers, providing greater flexibility in your installations.
Control is via manual selection buttons, WebGUI, Telnet, RS-232 or IR
remote.
2. APPLICATIONS
Full audio/video matrix systems
Residential AV matrix installations
Commercial AV matrix installations
Security systems
University lecture hall systems
Retail installation systems

7
3. PACKAGE CONTENTS
1× 6 by 8 HDMI and HDBaseT Matrix with Audio Matrixing
1× Remote Control (CR-163)
2× IR Blaster Cable
2× 24V/6.25A DC Power Adaptor
2× Power Cord
1× Rack Ear Set
1× Operation Manual
4. SYSTEM REQUIREMENTS
HDMI or DVI source equipment such as media players, video game
consoles, set-top boxes, PCs or laptops. DVI equipped source devices
must be connected via DVI to HDMI cables/adapters
HDMI receiving equipment such as HDTVs, monitors or audio
ampliers
The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly
recommended
HDBaseT™ receivers equipped with Optical Audio Return (OAR)
channel support are strongly recommended
The use of “Premium High Speed HDMI” cables is highly recommended

8
5. FEATURES
HDMI 2.0, HDCP 1.4 and HDCP 2.2 compliant
Routes 6 HDMI sources to 8 displays using 6 HDBaseT outputs and 2
independent or mirrored HDMI outputs
HDBaseT feature support: High-Denition video and audio, 48v PoH
(Power over HDBaseT) and control (Bi-directional IR & RS-232 pass
through)
Supported HDBaseT resolutions: VGA~WUXGA, 480i~1080p,
4K@24/25/30Hz (RGB, YUV 4:4:4 & YUV 4:2:2) & 4K@60Hz (YUV 4:2:0)
dependent upon the output display’s EDID settings
Supports HDMI output resolutions up to 4K@60Hz (RGB/YUV 4:4:4)
Supports automatic 4K@60Hz RGB/YUV 4:4:4 to YUV 4:2:0 conversion
for HDBaseT outputs
4K@30Hz signals can be transmitted up to 35m via Cat.5e/6 and up to
60m via Cat.6a/7
Supports pass-through of all standard digital audio formats: LPCM
2.0/5.1/7.1, bitstream, and HD bitstream
Supports audio matrix functionality enabling full audio management
of the system including HDBaseT audio selection, fully independent
audio-only zones and HDMI audio embedding and de-embedding
(LPCM only)
Supports Digital to Analogue Conversion (DAC) and Analogue to
Digital Conversion (ADC) for audio integration
Supports volume, treble, bass, and audio delay for lip-sync (up to
230ms) on analogue audio outputs and mute on all outputs
HDBaseT outputs with Optical Audio Return (OAR) support
Advanced internal and external EDID management with 4 sets of
congurable EDID settings
Internal test pattern generation for self and sink testing
Capable of generating test signals up to 4K@60Hz
Bi-directional IR support over HDBaseT
Supports supplying 48v PoH (Power over HDBaseT) to compatible
receivers (with use of optional 2nd power supply)
Control via front panel controls, Ethernet (Telnet & WebGUI), RS-232, &
IR remote
2U rack mounted design

9
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
POWER
ENTER
PRESET
MENU
/CANCEL
LOCK
A1B2C3D4E5
F6G7H8910
+
IN
-
OUT
1 2 3 6 7 8 95 104
1POWER: Press this button to power the unit on or place it into stand-
by mode.
Note: Network functionality and PoH (if the second power supply is
connected) remain active when the unit is in stand-by mode.
2POWER LED: This LED will illuminate GREEN to indicate the unit is on
and receiving power. When the unit is in stand-by mode the LED will
illuminate RED.
3IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
4OUTPUT A~H & INPUT/NUMBER 1~6: Press the “OUT” button to
enter output selection mode. Next, press the output keys (A~H) of
the outputs you wish to route a source to (they will ash to indicate
selection). Next, press the “IN”key followed by the input (1~6) you
wish to route to the selected outputs. Finally, press “ENTER” to conrm
your selection and execute the routing change.
For example, if you wish to display input 1 on outputs A~D then the
following sequence of button presses should be performed: OUT →A,
B, C, D →IN →1 →ENTER
When directly entering Ethernet address information into the unit all
10 buttons are used to represent the numbers from 0 to 9 (button 10
= 0) to make number entry more streamlined.
5MENU/CANCEL: Press the“MENU/CANCEL” button to enter the OLED
menu, or to back out from menu items. For a description of the menu
tree, please refer to section 6.5.
6ENTER: Press this button to conrm selections.
7+/IN: Within the menu, this button moves you up within the menu

10
tree. Otherwise, in routing mode, this button allows you to make your
input source selection.
-/OUT: Within the menu, this button moves you down within the
menu tree. Otherwise, this button starts routing mode and allows you
to begin your output destination selections.
8PRESET: Press this button to recall saved presets. A maximum of 8
presets can be stored in the unit. Presets are created and stored via the
WebGUI. Please refer to section 6.10.1 for advanced preset settings.
9LOCK: Press and hold this button for 3 seconds to lock/unlock all
buttons on the front panel. The OLED will display an “L”in the upper
right corner to indicate the front panel is locked.
10 OLED WINDOW: Displays the unit’s menu, settings and information.
6.2 Rear Panel
CAT5e/6 OUT
HDMI IN HDMI IN HDMI IN HDMI IN HDMI IN HDMI IN
IR IN
IR OUTIR OUTIR OUTIR OUTIR OUTIR OUT
1 2
A
RS-232 POH 24V
CAT5e/6 OUT
IR IN
B
3
CAT5e/6 OUT
IR IN
C
4
CAT5e/6 OUT
IR IN
D
5
CAT5e/6 OUT
IR IN
E
6
CAT5e/6 OUT
IR IN
F
MAIN 24V
SERVICE
B
AD
CF
E2 12 11
CAT5e/6 OUT
HDMI IN HDMI IN HDMI IN HDMI IN HDMI IN HDMI IN
IR IN
IR OUTIR OUTIR OUTIR OUTIR OUTIR OUT
1 2
A
ZONE ANALOG DIGITAL
ALLCONTROL RS-232
CAT5e/6 OUT
IR IN
B
3
CAT5e/6 OUT
IR IN
C
4
CAT5e/6 OUT
IR IN
D
5
CAT5e/6 OUT
IR IN
E
6
CAT5e/6 OUT
IR IN
F
HDMI OUTHDMI OUT MAIN 24V
SERVICE
IR IN IR OUT
GH
B
A
L
R
L
R
D
CF E2 12 11
AUDIO OUT
AUDIO OUT
AUDIO IN
1
2
3
4
V+
GND
GND GND
V+
L
R
L
R
EXTENDED
AUDIO IN
2
6 7 8 9 10 11
1 2 3 4 5 12 13
1HDMI IN & IR OUT 1~6: Connect up to 6 source devices to the HDMI
ports using appropriate quality HDMI cables. Input source devices
include Blu-ray players, set-top boxes, game systems and so on. These
inputs are DVI-D compliant (with the use of DVI to HDMI adapters or
cables). Attach IR blasters to the IR Out ports to transmit the IR signals
received from connected HDBaseT Receivers. The IR signal routing
follows the HDMI signal routing.
Note: The use of “Premium High Speed HDMI” cables is highly
recommended.
2CAT5e/6 OUT & IR IN A~F: Connect the Cat.5e/6 outputs via an
appropriate cable to the input ports of compatible HDBaseT receivers
for HDMI audio/video and IR/RS-232 control signal transmission. In
order for an IR signal to be transmitted along with the HDMI signal an
IR extender must be connected to the associated IR In port. IR signals
coming back from the connected HDBaseT receiver can be used to

11
control the matrix remotely and will also be broadcast from IR blasters
connected to the appropriate IR Out/All IR Out ports.
Note: 4K signals with HDR (High Dynamic Range) or Deep Colour are
supported by the 2 HDMI output ports, however they are not supported
by the HDBaseT outputs due to bandwidth limitations. If your HDR source
needs to be output over the HDBaseT outputs please remember to disable
the HDR support on your source device or use a non-HDR supporting
EDID.
3IR IN (ALL): Connect an IR extender to this port for IR signal reception.
All IR signals received will be broadcast by all IR blasters connected
to the matrix or connected HDBaseT receivers. Please ensure that the
remote being used is within direct line-of-sight of the IR extender.
4IR OUT (ALL): Connect an IR Blaster to this port to broadcast IR signals.
All IR signals received by any IR extenders connected to the matrix
or HDBaseT receivers will be broadcast. Please place the IR Blaster in
direct line-of-sight of the equipment to be controlled.
5HDMI OUT G & H: Connect up to 2 HDMI displays using these HDMI
output ports. These two HDMI ports can be either independent high
bandwidth (18Gbps) outputs, or they can be congured to mirror two
of the HDBaseT outputs for local monitoring or recording purposes.
Note: 4K signals with HDR (High Dynamic Range) or Deep Colour are
supported by the 2 HDMI output ports, however they are not supported
by the HDBaseT outputs due to bandwidth limitations. If your HDR source
needs to be output over the HDBaseT outputs please remember to disable
the HDR support on your source device or use a non-HDR supporting
EDID.
6ZONE AUDIO OUT A~F: Six sets of stereo analogue audio outputs.
These audio ports are capable of independently outputting audio
routed from any audio source within the matrix. Treble, bass, volume
and audio delay adjustments can be set in the WebGUI (LPCM 2.0 or
analogue stereo sources only).
7EXTENDED AUDIO OUT 1~2: Two sets of stereo analogue audio
outputs. These audio ports are capable of independently outputting
audio routed from any audio source within the matrix. Treble, bass,
volume and audio delay adjustments can be set in the WebGUI (LPCM
2.0 or analogue stereo sources only).
8ANALOGUE AUDIO IN 1~2: Accepts unbalanced analogue audio
from sources such as DVD players, PCs, MP3 players, etc. These audio

12
sources can be paired with the video from any HDMI input.
9DIGITAL AUDIO IN 1~2: Accepts digital audio (LPCM 2.0 only) from
sources such as Blu-ray players, game systems, PCs, etc. These audio
sources can be paired with the video from any HDMI inputI.
10 CONTROL: Connect directly, or through a network switch, to your PC/
laptop to control the unit via Telnet/WebGUI.
11 RS-232: Connect directly to your PC/laptop to send RS-232 commands
to control the unit (refer to section 6.7).
12 SERVICE: Used for rmware service updates in the eld via USB thumb
drive. After connecting a USB thumb drive containing appropriate
rmware, please navigate via the front panel menu to 5-Firmware →
2-Update →YES to begin the rmware update.
13 MAIN 24V & POH 24V: Plug one of the 24V power supplies (included
in the package) into the port marked “MAIN 24V” to power the matrix
unit. If you wish to connect PoH powered HDBaseT receivers to the
matrix, please plug the second 24V power supply into the “POH 24V”
port. This will allow the matrix to provide 48v PoH to all connected
HDBaseT receivers.
6.3 Side Panel
1
1FAN VENT: These are air ventilation areas. DO NOT block these areas
or cover them with any objects. Please allow adequate space around
the unit for air circulation.

13
6.4 Remote Control
1POWER: Press to power the unit on or place it
into stand-by mode.
2LOCK: Press to lock/unlock the front panel of
the matrix unit.
3MUTE: Mutes Zone Audio outputs. HDBaseT
audio can only be muted when an independent,
non-HDMI, audio source has been routed to the
output.
4IN 1~6, OUT A~H & PATTERN:
[Local matrix control]: When controlling the
unit directly. Input selection from 1~6 plus test
patterns (pattern button) and output selection
from A~H (refer to section 6.1).
[Zone A/V Pairing]: When controlling the unit
via an HDBaseT receiver in a remote location.
Pressing buttons 1~10 will switch to the A/
V source assigned to the number depending
on your current zone. These assignments are
congured via the WebGUI (refer to section 6.10.6).
5MENU/CANCEL: Press the“MENU/CANCEL” button to enter the OLED
menu, or to back out from menu items.
6PRESET: Recall matrix presets. The presets are congured within the
WebGUI.
7+/IN: Within the menu, this button moves you up within the menu
tree. Otherwise, in routing mode, this button allows you to make your
input source selection.
-/OUT: Within the menu, this button moves you down within the
menu tree. Otherwise, this button starts routing mode and allows you
to begin your output destination selections.
◄/VOL- & ►/VOL-: Adjust volume of zone audio.
ENTER: Press this button to conrm selections.
Note: This remote control is designed for the full family of matrix products.
Some functions are not available on all units.
POWERLOCKMUTE
1/A 2/B 3/C
4/D 5/E 6/F
7/G 8/H 9/I
10/J PATTERN
+/IN
MENU/
CANCEL
PRESET
/VOL+
/VOL-
CR-163
ENTER
-/OUT
1
2
4
3
5
7
6

14
6.5 OLED Menu
1ST LEVEL 2ND LEVEL 3RD LEVEL
EDID EDID Mode All
Independent
EDID Select All
1~6 (Default EDID
settings)
7~14 (Sink's EDID
settings)
15~18 (User's EDID
settings)
Network Link Status (Idle)
IP Address
Subnet Mask
Gateway Address
MAC Address
DHCP mode On
O
HDMI Mirroring Output G
Output H
Factory Default Yes
No
Firmware Version
Update Yes
No
Note: The model name and IP address will be displayed when the unit is
powered on. The netmask and gateway information can be displayed by
repeatedly pressing the “+” button on the front panel or remote control unit.

15
6.6 IR Cable Pin Assignment
3
1
2
3
2
1
IR Blaster
Power
IR Signal
NC
IR Signal
Power
Ground
IR Extender
6.7 RS-232 Protocol
MATRIX
►
◄
REMOTE CONTROLLER
Pin Assignment Pin Assignment
1 NC 1 NC
2TX 2RX
3RX 3TX
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bits: 8
Parity: None
Flow Control: None
Stop Bits: 1

16
6.8 RS-232 and Telnet Commands
6.8.1 Command Syntax
The RS-232/Telnet command structure for this unit is both exible and
powerful, and allows for multiple parameters to be set across multiple
ports simultaneously within a single command transmission. This section
will detail the command syntax used to send both simple (single port/
single parameter) commands as well as the more complex (multi-port/
parameter) commands.
The following multi-function syntax is specically for use with
these commands: “ZoneLineOut”, “ExtLineOut”, “HDMI_Out”, “HDBT_
Out”, and “Pattern”. “ZoneAvPair” has a special structure that will be
explained separately. All other commands must be sent within discrete
transmissions.
Basic Command Format
Use this syntax to set or change a single parameter for a single input/
output port.
<Command> {Port} {Parameter [= Value]}
Examples: ZoneLineOut B Treble= -12
HDBT_Out A Mute
Basic Command Format (ZoneAvPair)
The ZoneAvPair command requires multiple variables to dene the
location of the slot’s value to adjust. This command only accepts 3
possible parameters:“VideoSrc”, “AudioSrc”, and“Load”. Use the following
syntax to set or change a single parameter for a single slot assigned to an
HDBaseT or HDMI output port.
ZoneAvPair HDBT_Out {Port} Slot {Slot} {Parameter [= Value]}
Examples: ZoneAvPair HDBT_Out B Slot 5 VideoSrc = HDMI_In 2
ZoneAvPair HDMI_Out H Slot 3 Load
Multi-Port Command Format
Use the following syntax to set or change a single parameter for multiple
ports. Note that each additional port uses the “+”character for separation.
The number of ports allowed in a single command is limited by the

17
number of ports on that specic interface.
<Command> {Port1}+{Port2}+{Etc.} {Parameter [= Value]}
Examples: ZoneLineOut A+B+C Treble = -12
HDBT_Out A+D+F Mute
Multi-Slot Command Format (ZoneAvPair)
The ZoneAvPair command allows for multiple slots on a single HDBaseT
or HDMI output to be assigned the same value simultaneously. Use the
following syntax to accomplish this. Note that each additional slot uses
the “+”character for separation. The number of slots allowed in a single
command is limited by the number of slots on that specic interface.
ZoneAvPair HDBT_Out {Port} Slot {Slot1}+{Slot2}+{Etc.} {Param [=
Value]}
Example: ZoneAvPair HDBT_Out B Slot 1+3+5 VideoSrc = HDMI_In 2
Multi-Parameter Command Format
Use the following syntax to set or change multiple parameters for a
single port. Note that each additional parameter uses the “,” character for
separation and spaces are allowed. The number of parameters allowed in
a single command is limited only by the number of individual parameters
that command has.
<Command> {Port} {Param1 [= Value]}, {Param2 [= Value]}, {Etc.}
Examples: ZoneLineOut C Treble = -12, Mute, Delay = 100
HDBT_Out A VideoSrc = HDMI_In 1, AudioSrc = HDMI_In 1
Multi-Parameter Command Format (ZoneAvPair)
The “VideoSrc”, “AudioSrc” and “Load” parameters may be combined on a
ZoneAvPair command. Note that the “,” character is used for separation.
ZoneAvPair HDBT_Out {Port} Slot {Slot} {Param1=Value},
{Param2=Value}
Example:
ZoneAvPair HDBT_Out B Slot 5 VideoSrc=HDMI_In 2, AudioSrc=CoaxIn 1

18
Complex Multi-Port/Parameter Command Format
It is possible to have a single command that aects multiple ports with
multiple groupings of parameters. All previously explained syntax rules
must be observed and each additional set of ports/parameters are
separated by the“&” character.
<Command> {Port1}+{Port2}+{Etc.} {Param1 [= Value]}, {Param2 [=
Value]}, {Etc.} & {Port1}+{Port2}+{Etc.} {Param1 [= Value]}, {Param2 [=
Value]}, {Etc.} & Etc.
Example:
HDBT_Out A+C+E VideoSrc=HDMI_In 2, AudioSrc=CoaxIn 1 & B+D Mute & F
VideoSrc=HDMI_In 1, AudioSrc=HDMI_In 1
Complex Multi-Slot/Parameter Command Format (ZoneAvPair)
The ZoneAvPair command can also control multiple slots with multiple
parameter groupings however the syntax is slightly dierent. Each
command can only aect a single port at a time. Each additional set of
slots/parameters are separated by the “&”character.
ZoneAvPair HDBT_Out {Port} Slot {Slot1}+{Slot2}+{Etc.}
{Param1=Value}, {Param2=Value} & Slot {Slot1}+{Slot2}+{Etc.}
{Param1=Value}, {Param2=Value} & Etc.
Example:
ZoneAvPair HDBT_Out B Slot 1 VideoSrc=HDMI_In 2, AudioSrc=CoaxIn
1 & Slot 2+3+4 VideoSrc=HDMI_In 2, AudioSrc=AnalogIn 1 & Slot 5+6
VideoSrc=HDMI_In 1, AudioSrc=HDMI_In 1 & Slot 1 Load
6.8.2 Real World Command Use
Zone A/V Pairing Mode Command Example
The easiest way to use the matrix for simple HDMI switching while still
allowing for individually tailored zone audio is to use the Zone A/V Pairing
setting within the WebGUI.
This is a congured and saved setting allowing each HDMI input to be
paired with dierent audio inputs, depending on the zone it is being
output to, for easy selection from a remote within that zone. For example,
certain zones might not be able to handle surround sound, so you can
pair the video in that zone with stereo inputs. Please review to section
6.10.6 for details of Zone A/V Pairing conguration.

19
COMMAND DESCRIPTION
ZoneAvPair HDBT_Out A Slot 1 Load Load the 1st A/V pairing for
HDBaseT Output A’s zone
Optical Audio Return (OAR) Command Example
If you are also using the Zone Audio outputs (Stereo Zones) for any zone
we recommend using the Optical Audio Return (OAR) function to set the
Zone Audio output to always play the audio coming from the TV itself.
In this way the end user can freely switch between the matrix input on
the TV and the internal tuner/smart functions of the TV and always be
guaranteed audio (remember to set the TV’s optical output to LPCM 2.0).
This command only needs to be resent after an audio only source has
been selected for that individual Zone Audio output. Commonly a control
system would have a “TV” button in the audio source selection area along
with your other audio sources.
COMMAND DESCRIPTION
ZoneLineOut A AudioSrc=OAR_In A Zone Audio output“A” plays OAR
audio from the TV connected to
HDBaseT output “A”
HDMI Mirroring Command Example
If you have rack (head end) based AVR’s for surround sound rooms we
recommend using the HDMI outputs and the HDMI mirroring mode to
easily have the audio and video sent to the AVR follow the signal sent to
that zone’s TV.
As long as no further commands are ever sent to the HDMI outputs of the
matrix you only need to set this up once:
COMMAND DESCRIPTION
HDMI_Out H Mirroring=HDBT_Out A Set HDMI output “H” to mirror
HDBaseT output “A”
When using the mirroring function you can use any standard commands
with the mirrored HDBaseT output and the mirroring HDMI output
will follow the commands. These can be an A/V Pairing, Video or Audio
commands, etc.

20
Audio Only source selection Command Examples
This unit oers 4 direct audio only inputs, while some of these inputs will
likely be used for down mixed audio signals from surround sound sources
(for stereo only zones) we expect audio only sources to be connected to
deliver just audio to both TV zones and Audio Only zones.
COMMAND DESCRIPTION
ZoneLineOut A AudioSrc=AnalogIn 1 Route Analogue input 1 to Zone
Audio output “A”
ZoneLineOut A AudioSrc=OpticIn 1 Route Optical input 1 to Zone
Audio output “A”
ZoneLineOut A AudioSrc=CoaxIn 1 Route Coaxial input 1 to Zone
Audio output “A”
ExtLineOut 1 AudioSrc=AnalogIn 1 Route Analogue input 1 to
Extended Line output “1”
ExtLineOut 1 AudioSrc=OpticIn 1 Route Optical input 1 to Extended
Line output “1”
ExtLineOut 1 AudioSrc=CoaxIn 1 Route Coaxial input 1 to Extended
Line output “1”
Above are just a few example of the audio selections available. Please
refer to the full command listing for all possible commands. Remember if
you have congured any audio zones to play the OAR audio from the TV
within a zone you must be able to select this again to return to “listening”
to that TV.
Individual Audio and Video Routing Command Examples
To oer the greatest level of exibility the matrix can be used to send
individual commands for both video and audio, this allows the installer
to completely tailor the matrix to suit any possible conguration the end
user may require.
Route audio and video from HDMI input 1 to HDBaseT output A
independently:
COMMAND DESCRIPTION
HDBT_Out A VideoSrc=HDMI_In 1 Video switch command
HDBT_Out A AudioSrc=HDMI_In 1 Audio switch command