CYP PRO-F32M User manual

OPERATION MANUAL
PRO-F32M
4K HDMI over Fiber 3 x 2 matrix.

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 12/02/2019 First release

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................7
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Front Panel................................................... 8
6.2 Rear Panel..................................................... 9
6.3 Remote Control.......................................... 9
6.4 IR Cable Pin Assignments .....................10
6.5 RS-232 Protocol........................................10
6.6 RS-232 and Telnet Commands............11
6.7 Telnet Control............................................14
6.8 WebGUI Control .......................................15
7. Connection Diagram .......................... 21
7.1 HDMI Switching .......................................21
7.2 Fiber Extension.........................................22
8. Specifications...................................... 23
8.1 Technical Specifications ........................23
8.2 Video Specifications................................24
9. Acronyms............................................. 25

6
1. INTRODUCTION
This 3×2 HDMI and Fiber Matrix allows customer to route up to three
HDMI input signals (two 18Gbps HDMI and one 10.2Gbps HDMI over
optical fiber) to any of two HDMI outputs (one 18Gbps HDMI and one
10.2Gbps optical fiber). The optical fiber input and output both support
transmission distances up to 300 metres and use paired LC connectors.
This unit supports resolutions up to 4K@60Hz (4:4:4, 8-bit), 16-bit Deep
Colour up to 1080p@60Hz, HDR (High Dynamic Range), HD audio formats
and other features defined by the HDMI 2.0 specification. HDMI sources
with bandwidth higher than 10.2Gbps are automatically chroma and/
or bit-depth subsampled for transmission over the fiber output. Six pre-
defined internal EDIDs and two external EDID selections are available for
EDID management. The unit provides intuitive front panel controls as well
as RS-232, Telnet, WebGUI and IR remote control options.
2. APPLICATIONS
Entertainment Rooms & Home Theatres
Showrooms & Demo Rooms
Lecture Hall Presentations
Public Commercial Displays
3. PACKAGE CONTENTS
1×3 by 2 HDMI and Fiber Matrix
1×Remote Control (CR-155)
1×IR Extender Cable
1×3.5mm to 9-pin D-sub Adapter
1×5V/2.6A DC Power Adaptor
1×Operation Manual

7
4. SYSTEM REQUIREMENTS
HDMI source equipment such as media players, video game consoles
or set-top boxes.
HDMI receiving equipment such as HDTVs, monitors or audio
amplifiers.
The use of “Premium High Speed HDMI”cables is highly
recommended.
Use of the optical fiber input/output requires a second unit and
appropriate paired LC multi-mode fiber in a crossover configuration.
5. FEATURES
HDMI with 3D & 4K@60Hz with HDR support
DVI 1.0 compliant with the use of an HDMI-DVI adaptor
HDCP 2.2 and 1.x compliant
Supports HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &
4096×2160@60Hz (4:4:4, 8-bit)
Supports 16-bit Deep Colour up to 1080p@60Hz
2×HDMI (18Gbps) and 1×HDMI over fiber (LC pair, 10.2Gbps) inputs
1×HDMI (18Gbps) and 1×HDMI over fiber (LC pair, 10.2Gbps) outputs
HDMI sources with bandwidth higher than 10.2Gbps are automatically
chroma and/or bit-depth subsampled for transmission over the fiber
outputs
Fiber transmission distances of up to 300m
3×2 matrix routing between all inputs and outputs
Supports pass-through of audio formats: LPCM 2.0/5.1/7.1, Bitstream,
and HD Bitstream
Comprehensive EDID management support including 6 pre-defined
internal EDIDs and 2 external EDIDs
Supports control via front panel, WebGUI, Telnet, RS-232, and IR
remote

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
SERVICE POWER 123
OUT A
123
OUT B
PRO-F32M
1 2 3 4 5 6
1SERVICE: This slot is reserved for firmware update use only.
2IR WINDOW: Accepts IR signals from the included IR remote for
control of this unit only.
3POWER LED: This LED will illuminate green to indicate the unit is on
and receiving power. When the unit is in stand-by mode the LED will
illuminate red.
4POWER BUTTON: Press this button to power the unit on or place it
into stand-by mode.
Note: Ethernet, IR and RS-232 remain active while the unit is in stand-by
mode.
5OUT A BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output A. The LEDs will
illuminate to indicate the currently selected input for Output A. When
all 3 LEDs are blinking, the output is muted.
6OUT B BUTTON & LEDs: Press this button to sequentially switch
through the 3 available inputs, and mute, for Output B. The LEDs will
illuminate to indicate the currently selected input for Output B. When
all 3 LEDs are blinking, the output is muted.

9
6.2 Rear Panel
DC 5VIR INRS-232
CONTROL
FIBER A HDMI B
OUT
FIBER 3
HDMI 2HDMI 1
IN
1 2 3 4 5 6
1FIBER A & HDMI B OUT: Connect the HDMI output to HDMI TVs,
monitors or amplifiers for digital video and audio output. DVI displays
are supported with the use of an HDMI to DVI adapter. Connect the
fiber (paired LC) output to the fiber input on a second unit.
2HDMI 1~2 & FIBER 3 IN: Connect the HDMI inputs to HDMI source
equipment such as media players, game consoles or set-top boxes.
DVI sources are supported with the use of an HDMI to DVI adapter.
Connect the fiber (paired LC) input to the fiber output from a second
unit.
3CONTROL: Connect directly, or through a network switch, to your PC/
laptop to control the unit via Telnet/WebGUI.
4RS-232: Connect, via the provided 9-pin adapter cable, to a PC, laptop
or other serial control device to send RS-232 commands to control the
unit.
5IR IN: Connect to the provided IR Extender to extend the IR control
range of the unit. Ensure that the remote being used is within direct
line-of-sight of the IR Extender.
6DC 5V: Plug the 5V DC power adapter into the unit and connect it to
an AC wall outlet for power.
6.3 Remote Control
1POWER: Press this button to power the unit on or
place it into stand-by mode.
2A1~A3 & B1~B3: Press any of these buttons to switch
immediately to the corresponding input for the
specified output (A or B).
Note: A4 & B4 have no function with this unit.
CR-155
POWER
1
2
3
4
1
2
3
4
BA
2
1

10
6.4 IR Cable Pin Assignments
3
1
2
IR Signal
Power
Ground
IR Extender
6.5 RS-232 Protocol
UNIT
►
◄
REMOTE SYSTEM
Pin Definition Pin Definition
1 NC 1 NC
2TxD 2 RxD
3 RxD 3 TxD
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data Bits: 8
Parity Bits: None
Stop Bits: 1
Flow Control: None

11
6.6 RS-232 and Telnet Commands
COMMAND DESCRIPTION AND PARAMETERS
HELP Displays all available commands.
?Displays all available commands.
P0 Turn unit’s power off. (Stand-by mode)
P1 Turn unit’s power on.
INNAME N1 N2 Set input N1 to name N2.
N1 = 1 ~ 3 [Input number]
N2 = {name} [16 characters max]
INNAME ? Show the current input names.
OUTNAME N1 N2 Set output N1 to name N2.
N1 = A ~ B [Output letter]
N2 = {name} [16 characters max]
OUTNAME ? Show the current output names.
OUT N1 N2 Set the input/output routing.
N1 = A ~ B [Output letter]
N2 = 0 ~ 3 [Input number. 0 = Mute]
OUT ? Show the current input/output routing.
SOURCEDET Show all source information.
SINKINFO Show all sink information.
HDCPIN N1 N2 Set the HDCP mode for input N1.
N1 = 1 ~ 3 [Input number]
Available values for N2:
1[Follow In]
2[Follow Out]
3[Apple Mode]
HDCPIN ? Show the current HDCP input settings.

12
COMMAND DESCRIPTION AND PARAMETERS
EDIDMODE N1 Set the EDID mode.
Available values for N1:
1[All]
2[Appoint]
EDIDMODE ? Show the current EDID mode setting.
EDIDALL N1 Set the EDID to use in“All”mode.
Available values for N1:
1[FHD/2CH]
2[FHD/MCH]
3[4K UHD/2CH]
4[4K UHD/MCH]
5[4K UHD+/2CH]
6[4K UHD+/MCH]
7[SINK A]
8[SINK B]
EDIDALL ? Show the current EDID selection for“All”mode.
EDIDIN N1 N2 Set the EDID to use on input N1 in “Appoint”
mode.
N1 = 1 ~ 3 [Input number]
Available values for N2:
1[FHD/2CH]
2[FHD/MCH]
3[4K UHD/2CH]
4[4K UHD/MCH]
5[4K UHD+/2CH]
6[4K UHD+/MCH]
7[SINK A]
8[SINK B]
EDIDIN ? Show the current EDID selection for each input
in “Appoint” mode.
HDMIOUTSCALE N1 Set the HDMI output scaler mode.
Available values for N1:
1[Bypass]
2[4K2K@60_420 to 444]

13
COMMAND DESCRIPTION AND PARAMETERS
HDMIOUTSCALE ? Show the current HDMI output scaler mode.
IPCONFIG Show the current IP configuration.
SETIP N1 N2 N3 Set the IP Address, Netmask, and Gateway for
the unit when in Static IP mode with a single
command. Disables DHCP.
N1 = X.X.X.X [X = 0 ~ 255, IP Address]
N2 = X.X.X.X [X = 0 ~ 255, Netmask]
N3 = X.X.X.X [X = 0 ~ 255, Gateway]
SIPADDR N1 Set the IP Address. Disables DHCP.
N1 = X.X.X.X [X = 0 ~ 255]
SNETMASK N1 Set the Ethernet netmask. Disables DHCP.
N1 = X.X.X.X [X = 0 ~ 255]
SGATEWAY N1 Set the Ethernet gateway. Disables DHCP.
N1 = X.X.X.X [X = 0 ~ 255]
RSTIP Reset the unit’s Ethernet mode to DHCP.
ECHO N1 Enable or disable echo when using the console.
Available values for N1:
0[Off ]
1[On]
ECHO ? Show the current console echo state.
FADEFAULT Reset the unit to the factory defaults.
VER Show the unit’s current firmware version.
REBOOT Reboot the unit.
ETH_FADEFAULT Reset all Ethernet settings to the factory
default.
Note: Commands will not be executed unless followed by a carriage return.
Commands are not case-sensitive.

14
6.7 Telnet Control
Before attempting to use Telnet control, please ensure that both the unit
and the PC/Laptop are connected to the same active networks.
To access Telnet
In Windows 7 Click Start, type “cmd” in the search field, and
press Enter.
In Windows XP Click Start > Run, type “cmd”, and press Enter.
In Mac OS X Click Go > Applications > Utilities > Terminal.
Once in the CLI (Command Line Interface) type “telnet” followed by the IP
address of the unit and “23”, then hit “Enter”.
This will connect us to the unit we wish to control. Type “help” to list the
available commands.
Notes:
Commands will not be executed unless followed by a carriage return.
Commands are not case-sensitive.
If the IP address is changed then the IP address required for Telnet access will
also change accordingly.

15
6.8 WebGUI Control
Device Discovery APP
Please obtain the “Device Discovery” software from your authorised dealer
and save it in a directory where you can easily find it.
Connect the unit and your PC/Laptop to the same active network and
execute the“Device Discovery” software. Click on “Find Devices on
Network”and a list of devices connected to the local network will show
up indicating their current IP address. (The unit’s default IP address is
192.168.1.50)
By clicking on one of the listed devices you will be presented with the
network details of that particular device.
(1) IP Mode: If you choose, you can alter the static IP network settings for
the device, or switch the unit into DHCP mode to automatically obtain
proper network settings from a local DHCP server. To switch to DHCP
mode, please select DHCP from the IP mode drop-down, then click
“Save” followed by “Reboot”.
(2) WebGUI Hotkey: Once you are satisfied with the network settings,
you may use them to connect via Telnet or WebGUI. The network
information window provides a convenient link to launch the WebGUI
directly.

16
WebGUI Control Page
After connecting to the WebGUI’s address in a web browser, log into the
unit by entering the appropriate user name and password. The default
user name and password are “admin”.
All primary functions of this unit are controllable via the built in WebGUI,
including power control, input selection, EDID management, HDCP
management, port labeling, and Ethernet settings. The individual
functions will be introduced in the following section.

17
1. POWER
The unit can be powered on or off (stand-by mode) from this tab.
2. ROUTING
This tab allows for the selection of the input source for each output. Three
inputs and mute (sync only, no video or audio) are selectable. The switch
will occur immediately upon selection of a new source.
3. EDID
This tab provides EDID management controls for the unit. All inputs can
share the same assigned EDID, or each input can have a discrete EDID
assigned to it.
(1) ALL: Selecting the “ALL”mode will send the selected EDID to all inputs.
(2) APPOINT: Selecting the “APPOINT” mode allows for each input to
have a different EDID assigned to it.

The available EDID options are:
(1) FHD/PCM 2CH: 1080p@60Hz, LPCM 2.0
(2) FHD/Bitstream: 1080p@60Hz, LPCM 7.1 + Bitstream
(3) 4K UHD/PCM 2CH: 4K@30Hz, LPCM 2.0
(4) 4K UHD/Bitstream: 4K@30Hz, LPCM 7.1 + Bitstream
(5) 4K UHD+/PCM 2CH: 4K@60Hz, LPCM 2.0
(6) 4K UHD+/Bitstream: 4K@60Hz, LPCM 7.1 + Bitstream

18
(7) SINK A: EDID from the device on Output A
(8) SINK B: EDID from the device on Output B
4. HDCP CONTROL
This tab allows for the HDCP mode to be switched between “Follow In”,
“Follow Out” and “Apple” mode. “Apple”mode allows for the display of
non-HDCP required content from Apple devices on non-HDCP displays.
This setting can be assigned individually to each input.
5. HDMI OUT B MODE
This tab allows control over the handling of 4K@60Hz (4:2:0) sources
when output from Output B. The signal can be passed unmodified (Bypass)
or it can be colour up-sampled from 4:2:0 to 4:4:4 (4K2K@60_420 to 444).
Please make the selection that is appropriate based on the capabilities of
the connected display.
6. NAMING
This tab allows for the renaming of the three Input ports and the two
Output ports. Please click the“SAVE”button to store the changes.

19
7. NETWORK SETTING
This tab provides control over the unit’s network settings. The IP mode
can be set to DHCP for automatic IP configuration, if your local network
supports it, or it can be placed into STATIC mode. When in STATIC mode
the IP address, netmask and gateway can be defined manually.
8. LOGIN CONFIGURATION
This tab allows for the login password to be changed. The default
password is “admin”.
9. SOURCE DETECT
This tab displays the connection status of the 3 inputs. If a live source is
detected on an input it will display “CONNECTED”, if there is no live source
it will display “DISCONNECTED”.

20
10. STATUS
This tab displays the currently selected source for each output and the
unit’s current firmware version. Options for performing a factory reset or
rebooting the unit are also provided here.
11. FIRMWARE UPDATE
This tab provides a way to update the firmware of the unit.
(1) Browse: Click this button to select the firmware update *.bin file
which is located on your local PC.
(2) Update: Click this button to begin the firmware update process.
12. FIBER OUT A INFO & HDMI OUT B INFO
These tabs present the information detected from displays connected to
the Fiber and HDMI outputs, including type, manufacturer name, native
resolution, colour depth, 3D support, and audio format support.