CYP CH-2538TXPLWPKD User manual

CH-2538TXPLWPKD
4K UHD HDMI/VGA over HDBaseT Wallplate
Transmitter
CH-2527RXPL
4K UHD HDMI over HDBaseT Receiver
Operation Manual
Operation Manual


DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2018 by Cypress Technology.
All Rights Reserved.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufcient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
VS1 19/01/18 Final technical review
VS2 22/01/18 Additional RS-232 commands
VS3 26/01/18 Remotely RS-232 control only

CONTENTS
1. Introduction......................................................1
2. Applications.....................................................2
3. Package Contents ..........................................2
4. System Requirements......................................2
5. Features............................................................3
6. Operation Controls and Functions.................5
6.1 Transmitter's Front Panel ........................... 5
6.2 Transmitter's Rear Panel............................ 6
6.3 Receiver's Front Panel............................... 7
6.4 Receiver's Rear Panel ............................... 7
6.5 RS-232 Protocol.......................................... 8
6.6 RS-232 Commands.................................... 8
7. Connection Diagram ....................................12
8. Specications ................................................13
8.1 Transmitter's Technical Specications... 13
8.2 Receiver's Technical Specications...... 14
8.3 Video Specications............................... 15
8.4 Cable Specications .............................. 17
9. Acronyms .......................................................18

1
1. INTRODUCTION
Transmitter
This Transmitter is an HDMI/VGA switch with audio embedding and
HDBaseT output. The wall plate is designed for use with UK two-
gang sized enclosures. This Transmitter can send high denition
uncompressed audio/video over a single cable up to a distance of 70
meters at 1080p@60Hz.
The HDMI input supports resolutions up to 4K@60Hz (4:4:4, 8-bit). The
VGA input supports resolutions up to WUXGA (RB) and with the use of
the associated 3.5mm audio input, stereo audio may be embedded
as well. To provide maximum compatibility with a wide range of
display types, all sources will be automatically scaled to match the
preferred resolution and timing of the connected display (as reported
by the display's EDID). Despite HDBaseT’s 10.2Gbps bandwidth
limitation, even 4K UHD HDMI video sources, up to and including
4K@60Hz (4:4:4, 8-bit), can be supported by converting the signal to
4K@30Hz when necessary.
This unit also supports automatic input selection between the HDMI
and VGA inputs, with hot plug detection, enabling hands-free
operation. Additionally, the unit may be powered locally or via 48V
PoH (Power over HDBaseT) from a compatible HDBaseT Receiver,
which allows for greater exibility in installations.
Receiver
This receiver is a great solution for extending uncompressed HD
audio and video as well as Ethernet and control via a single run of
Cat.5e/6/7 cable over distances of up to 70 meters. Multiple data and
control interfaces are provided, including IR and RS-232 connections.
This Receiver complies with the advanced HDCP 2.2 and HDMI 2.0
standards, as well as supporting the legacy HDCP 1.x and HDMI 1.x
standards. This Receiver (PSE) can provide 48V PoH (Power over
HDBaseT) to compatible Transmitters allowing for greater exibility
within different installation scenarios.

2
2. APPLICATIONS
• Household entertainment sharing and control
• Lecture room display and control
• Showroom display and control
• Meeting room presentation and control
• Classroom display and control
3. PACKAGE CONTENTS
• 1×HDMI/VGA over HDBaseT Transmitter
• 1×HDMI over HDBaseT Receiver
• 1×48V/0.83A DC Power Adaptor
• 1×Power Cord
• 1×Operation Manual
4. SYSTEM REQUIREMENTS
• HDMI source equipment such as a media player, video game
console or set-top box.
• HDMI receiving equipment such as an HDTV, monitor or audio
amplier.
• The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly
recommended.
• The use of “Premium High Speed HDMI” cables is highly
recommended.

3
5. FEATURES
Transmitter
• HDMI 2.0 and DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• 1 HDMI input
• 1 VGA input with 3.5mm mini-jack audio input
• Supports HDMI input resolutions up to 4K@60Hz (4:4:4, 8-bit)
• Supports VGA input resolutions up to WUXGA (RB)
• Automatic conversion of 4K@50/60Hz HDMI sources to 4K@30Hz
(4:4:4, 8-bit) for transmission over HDBaseT
• Automatic scaling of sources to match the native resolution of the
HDMI display based on EDID
• HDBaseT feature support: HD Video and Audio, and 48V PoH
• Simultaneous transmission of uncompressed video and audio over a
single 70m Cat.5e/6/7 cable at 1080p and 35m at 4K
• Automatic input selection with hot plug detection enabling
handsfree operation
• Unit may be powered locally or via 48V PoH (PD) from a compatible
HDBaseT Receiver (PSE)
• Wall plate is designed for UK two-gang sized enclosures
• Controllable via front panel buttons and RS-232 (remote only)
• Front panel LEDs indicate input selection, power and link status

4
Receiver
• HDMI 2.0 and DVI 1.0 compatible
• HDCP 2.2 and HDCP 1.x compliant
• Supports resolutions up to 4K@50/60Hz (YUV 4:2:0, 8-bit)
• Supports CEC bypass
• Simultaneous reception of uncompressed video, audio and data
over a single 70m Cat.5e/6/7 cable at 1080p and 35m at 4K
• HDBaseT feature support: HD Video and Audio, 48V PoH, and
Control (IR and RS-232 bypass)
• Supports standard 48V PoH from Receiver (PSE) to Transmitter (PD)
(compatible Transmitters only)
Notes:
• The 48V PoH function is designed to power compatible Transmitter
units only. Non-PoH Transmitters will need their own power supply.
Other Transmitter brands may not be compatible.
• The use of “Premium High Speed HDMI” cables is highly
recommended for displaying 3D and 4K content. Compatible
display equipment is also required.

5
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter's Front Panel
LINKVGAHDMIPOWER
UHDWALLPLATE EXTENDER
HDMI VGASERVICE
ININ
IN
AUTO
ADJUST
IN
SEL
7
1 2 3 4 5 6
8 9 10
1POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
2HDMI IN LED: This LED will illuminate when HDMI is the selected
source.
3VGA IN LED: This LED will illuminate when VGA is the selected
source.
4LINK LED: This LED will illuminate solid when both Transmitter and
Receiver are connected and communicating with each other
properly.
5IN SEL: Press this button to switch between the available inputs. The
LED will illuminate to indicate which source is currently selected.
6AUTO ADJUST: Press this button to optimize the positioning of the
picture (VGA sources only).
Note: Pressing and holding the Auto Adjust button for 5 seconds
while the HDMI input is selected will reset the unit to its factory
defaults.
7SERVICE: This slot is reserved for rmware update use only.
8HDMI IN: Connect to HDMI source equipment such as a media

6
player, game console or set-top box.
9VGA IN: Connect to VGA source equipment such as a PC or
laptop.
10 AUDIO IN: Connect to the stereo analog output of a device such
as a CD player or PC for embedding into the HDBaseT output.
6.2 Transmitter's Rear Panel
DC 12V
+
−
CAT5e/6/7 OUT
2
1
1DC 12V: Plug a 12V DC power adapter into this port and connect
it to an AC wall outlet for power (optional, not required when
powered by PoH).
2CAT5e/6/7 OUT: Connect to a compatible HDBaseT Receiver with
a single Cat.5e/6/7 cable for transmission of all data signals.

7
6.3 Receiver's Front Panel
POWER
LINK
RS-232 OUT
STD UPDATE
1 2 43
1STD/UPDATE: This switch is reserved for factory use only.
2RS-232 OUT: Connect to a PC, laptop or other serial control device
to send control commands to a compatible Transmitter.
3POWER LED: This LED will illuminate to indicate the unit is on and
receiving power.
4LINK LED: This LED will illuminate solid when both Transmitter and
Receiver are connected and communicating with each other
properly.
6.4 Receiver's Rear Panel
CAT5e/6/7 IN
IR2
EXTENDER
IR1
BLASTER
HDMI OUT
DC 48V
2
13 4 5
1DC 48V: Plug the 48V DC power adapter into this port and connect
it to an AC wall outlet for power.
2IR1 BLASTER: Connect to the supplied IR Blaster cable for IR signal
transmission. Place the IR Blaster in direct line-of-sight of the
equipment to be controlled. (Requires compatible Transmitter.)
3IR2 EXTENDER: Connect to the supplied IR Extender cable for IR
signal reception. Ensure that remote being used is within the direct
line-of-sight of the IR Extender. (Requires compatible Transmitter.)
4CAT5e/6/7 IN: Connect to a compatible HDBaseT Transmitter with
a single Cat.5e/6/7 cable for transmission of all data signals.
5HDMI OUT: Connect to an HDMI TV, monitor or amplier for digital
video and audio output.

8
6.5 RS-232 Protocol
TX RX
Pin Pinout Pin Pinout
1 1
2TxD 2RxD
3RxD 3TxD
4 4
5 GND 5 GND
6 6
7 7
8 8
9 9
6.6 RS-232 Commands
COMMAND DESCRIPTION AND PARAMETERS
HELP Show the full command list.
?Show the full command list.
GET FW VER Show the unit’s rmware version.
GET MODEL NAME Show the unit’s model name.
SET FACTORY DEFAULT Reset all settings to the factory
defaults.
SET OUT A ROUTE N1 Select the input source.
Available values for N1:
1 [HDMI]
2 [VGA]
GET OUT A ROUTE Show the current input source.

9
COMMAND DESCRIPTION AND PARAMETERS
SET OUT AUTO MODE N1 Set the auto source select mode.
Available values for N1:
0 [OFF]
1 [Auto Switch]
GET OUT AUTO MODE Show the current auto source
select mode.
GET OUT AUTO MODE LIST List all available auto source
modes.
GET IN N1 TIMING Show the video timing of the
source connected to input N1.
Available values for N1:
1 [HDMI]
2 [VGA]
GET IN TYPE LIST List all available input types.
SET FIX TIMING MODE N1 Set the scaler’s output mode.
Available values for N1:
0 [Bypass]
1 [Auto]
2 [480P@60Hz]
3 [720P@50Hz]
4 [720P@60Hz]
5 [1080P@50Hz]
6 [1080P@60Hz]
7 [4K@24Hz]
8 [4K@25Hz]
9 [4K@30Hz]
GET FIX TIMING MODE Show the scaler’s current output
mode.

10
COMMAND DESCRIPTION AND PARAMETERS
SET FIX COLOR SPACE N1 Set the output color space.
Available values for N1:
0 [RGB]
1 [YUV 4:4:4]
GET FIX COLOR SPACE Show the current output color
space.
GET OUT A TIMING Show the video timing of the
output.
SET AUDIO OUT A ROUTE N1 Select the audio source.
Available values for N1:
1 [HDMI Audio]
2 [Analog Audio]
GET AUDIO OUT A ROUTE Show the currently selected
audio source.
GET AUDIO IN TYPE LIST List all available audio sources.
SET IN 1 HDCP MODE N1 Set the HDCP mode for the HDMI
input.
Available values for N1:
0 [Disable HDCP]
1 [Follow Source]
2 [Follow Display]
GET IN 1 HDCP MODE Show the current HDCP mode for
the HDMI input.
SET IN 1 EDID N1 Set the EDID to use with the HDMI
input.
Available values for N1:
1 [1080P, 2CH]
2 [4K (3G), 2CH]
3 [4K (6G), 2CH]
4 [Output’s EDID]

11
COMMAND DESCRIPTION AND PARAMETERS
GET IN 1 EDID Show the currently selected EDID
source for the HDMI input.
GET IN EDID LIST List all available EDID sources.
Note: Commands will not be executed unless followed by a carriage
return. Commands are not case-sensitive.

12
7. CONNECTION DIAGRAM
RX
CAT5e/6/7 IN
IR2
EXTENDER
IR1
BLASTER
HDMI OUT
DC 48V
TX LINKVGAHDMIPOWER
UHDWALLPLATE EXTENDER
HDMI VGASERVICE
ININ
IN
AUTO
ADJUST
IN
SEL
POWER
LINK
RS-232 OUT
STD UPDATE
DVD/Blu-ray Player
PC/Laptop
UHDTV
Power Supply
RS-232
RS-232 Equipped
PC/Laptop
HDMI
Input
VGA
Input
Stereo
Input
HDMI
Output
Cat.5e/6/7
Cable

13
8. SPECIFICATIONS
8.1 Transmitter's Technical Specications
HDMI Bandwidth 600MHz/18Gbps
HDBaseT Bandwidth 340Hz/10.2Gbps
Input Ports 1×HDMI
1×VGA
1×3.5mm (Stereo Audio)
Output Port 1×Cat.5e/6/7
Baud Rate 19200bps
Power Supply 12V/3A DC (US/EU standards, CE/FCC/
UL certied)
ESD Protection Human Body Model:
±8kV (Air Discharge)
±4kV (Contact Discharge)
Dimensions 147mm×87.5mm×41.5mm (W×H×D)
[Case Only]
147mm×87.5mm×46.6m (W×H×D)
[All Inclusive]
Weight 250g
Chassis Material Metal
Silkscreen Color White
Operating Temperature 0˚C - 40˚C/32˚F - 104˚F
Storage Temperature −20˚C - 60˚C/−4˚F - 140˚F
Relative Humidity 20 - 90% RH (Non-condensing)
Power Consumption 26.4W

14
8.2 Receiver's Technical Specications
HDMI Bandwidth 600MHz/18Gbps
HDBaseT Bandwidth 340Hz/10.2Gbps
Input Port 1×Cat.5e/6/7
Output Port 1×HDMI
Pass-through Ports 1×IR Extender [3.5mm]
1×IR Blaster [3.5mm]
1×RS-232 [9-pin D-sub]
IR Frequency 30 - 50kHz (30 - 60kHz under ideal
conditions)
Baud Rate Up to 115200bps
Power Supply 48V/0.83A DC (US/EU standards, CE/
FCC/UL certied)
ESD Protection Human Body Model:
±8kV (Air Discharge)
±4kV (Contact Discharge)
Dimensions 128mm×25mm×108mm (W×H×D)
[Case Only]
128mm×25mm×117m (W×H×D)
[All Inclusive]
Weight 366g
Chassis Material Metal
Silkscreen Color Black
Operating Temperature 0˚C - 40˚C/32˚F - 104˚F
Storage Temperature −20˚C - 60˚C/−4˚F - 140˚F
Relative Humidity 20 - 90% RH (Non-condensing)
Power Consumption 8.74W

15
8.3 Video Specications
Supported PC Resolutions (Hz)
Input Output
HDMI VGA
HDMI via
HDBaseT
640×480 60, 72, 75, 85
720×400 85
800×600 56, 60, 72, 75, 85
1024×768 60, 70, 75, 85
1152×864 75
1280×768 60, 75, 85
1280×800 60 (RB), 60
1280×960 60
1280×1024 60
1360×768 60
1366×768 60 (RB), 60 60 (RB)
1400×1050 60 (RB), 60
1440×900 60 (RB), 60
1600×1200 60
1680×1050 60 (RB), 60
1920×1200 60
1920×1440 60
2560×1600 60
This manual suits for next models
1
Table of contents
Other CYP Receiver manuals

CYP
CYP CH-507RXWPL User manual

CYP
CYP CH-107RXN User manual

CYP
CYP AVIP-P5104R-B1C User manual

CYP
CYP CPLUS-21FRX User manual

CYP
CYP CH-1529RXPLV User manual

CYP
CYP HDMI Over CAT5 User manual

CYP
CYP CH-527RXVBD User manual

CYP
CYP CH-507TXWPBD User manual

CYP
CYP CH-2603RX User manual

CYP
CYP IP-A750RX User manual