CYP PU-606PLBD-TX User manual

PU-606PLBD-TX & RX
HDBaseT™ LITE Receiver with Bi-directional PoE
& 2-Way IR (up to 60m)
OPERATION MANUAL

3
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer le, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

4
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sucient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE SUMMARY OF CHANGE
v1.00 02/10/2014 First release

5
CONTENTS
1. Introduction...........................................6
2. Applications ...........................................6
3. Package Contents ..................................6
4. System Requirements ...........................6
5. Features..................................................7
6. Operation Controls and Functions.......8
6.1 Transmitter Front and Rear Panels....... 8
6.2 Receiver Front and Rear Panels ............ 9
6.3 IR Pin Assignment....................................10
6.4 D-Sub 9 Pin Denitions .........................10
7. Connection and Installation .............. 11
7. Specications...................................... 12
8.1 Technical Specication ..........................12
8.2 CAT5e/6/7 Cable Specication ...........13
9. Acronyms............................................. 14

6
1. INTRODUCTION
The HDBaseT-LiteTM HDMI over single CAT5e/6/7 with bidirectional
IR, RS-232 & bidirectional PoC Transmitter and Receiver set gives you
the fexibilty of powering at the most convenient point (transmitter or
receiver) making your home or oce set-up more ecient and easier
to install. Uncompressed video and audio can be transmitted up to 60
meters with the PoC function and added benet of control through the
built-in RS-232 and IR ports.
2. APPLICATIONS
Household entertainment sharing and control
Lecture room display and control
Showroom display and control
Meeting room presentation and control for projector
Classroom display and control
3. PACKAGE CONTENTS
1×HDMI to CAT5e/6/7 with IR/RS232 & PoC
1× CAT5e/6/7 to HDMI with IR/RS232 & PoC
1× IR Blaster
1×IR Extender
1× 3.5mm to RS-232 female cable
1× 3.5mm to RS-232 male cable
1× 24V 1.25A DC Power Adaptor
1× Operation Manual
4. SYSTEM REQUIREMENTS
Input HDMI source equipment such as DVD/Blu-ray player/PC, output
display with HDMI input jack and connection cables of HDMI and
CAT5e/6/7.

7
5. FEATURES
Compatible with HDCP and DVI
Supports HDMI 3D and 4K x 2K features
Supports HDBaseT-Lite Technology
Supports HD resolutions up to 1080p@60Hz/36-bit
Supports distance up to 60 meters through CAT5e/6/7 cable
Supports bidirectional IR and PoC
HDMI input/output up to 15 meters with 8-bits resolution or 10 meters
with 12-bits resolution
S-232 with baud rate up to 115200/sec
Supports wide range of IR frequency from 30~50kHz
Supports HDCP repeater and CEC bypass
Audio supports LPCM 7.1CH, Dolby TrueHD, Dolby digital Plus and
DTS-HD Master Audio transmission

8
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Transmitter Front and Rear Panels
Power
Link
Lite CAT 5e /6 Out
DC 24V
IR2 Extender
RS232 In IR1 Blaster
HDMI In
RearFront
231 5
46
7
8
1RS232 In: Plug the 3.5mm to D-Sub 9-pin female cable included in
the package and connect to a PC or laptop for RS-232 commands
transmission.
2IR2 Extender: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR Extender.
3IR1 Blaster: Plug the IR Blaster included in the package for IR signal
sending from the Receiver side.
4HDMI In: Connect with source equipment such as DVD/Blu-ray player.
5DC 24V: Plug the 24V DC power supply into the unit and connect the
adaptor to an AC outlet. Only 1 side of device require power supply
when both Transmitter and Receiver obtain PoC function.
6LINK LED: This LED will illuminate when the devices are connected
with a CAT5e/6/7 cable from the Receiver side. When the data
transmission accrue with error the LED will be blinking.
7Power LED: This LED will illuminate when the devices are connected
with power supply.
8CAT5e/6 Out: Connect to the Receiver unit with a single CAT5e/6/7
cable for transmission of all data signals.

9
6.2 Receiver Front and Rear Panels
Power
Link
Lite CAT 5e /6 In
IR1 Extender
RS232 Out IR2 Blaster
HDMI Out
RearFront
DC 24V
675 8 2
3
4
1
1DC 24V: Plug the 24V DC power supply into the unit and connect the
adaptor to an AC outlet. Only 1 side of device require power supply
when both Transmitter and Receiver obtain PoC function.
2LINK LED: This LED will illuminate when the devices are connected
with a CAT5e/6/7 cable from the transmitter side. When the data
Transmission has an error the LED will blink.
3Power LED: This LED will illuminate when the device is connected
from the transmitter with power supply.
4CAT5e/6 In: Connect to the Transmitter unit with a single CAT5e/6/7
cable for transmission of all data signals.
5RS232 Out: Plug the 3.5mm to D-Sub 9-pin male cable included in the
package and connect to the device that is to be controlled by RS-232
commands
6IR1 Extender: Connect to the supplied IR Extender cable for IR signal
reception. Ensure that remote being used is within the direct line-of-
sight of the IR Extender.
7IR2 Blaster: Plug the IR Blaster included in the package for IR signal
sending from the Receiver side.
8HDMI Out: Connect to a HDMI equipped TV/monitor for display of the
HDMI input source signal.

10
6.3 IR Pin Assignment
3
1
2
3
2
1Power
IR Blaster Signal
NC
IR Signal
Power
Ground
IR Receiver
IR Blaster
6.4 D-Sub 9 Pin Denitions
Pin Dene TX / RX
1N/C
2TxD/RxD
3RxD/TxD
4N/C
5GND
6N/C
7N/C
8N/C
9N/C
9NC