Cypress Semiconductor CY4501 CCG1 DVK User manual

QUICK START GUIDE
CY4501 CCG1 DVK
CCG1 HOST BOARD
ONE SUPERSPEED USB
TYPE-A TO TYPE-B CABLE
TWO USB 2.0 TYPE-A TO
MINI-B CABLES
MINIPROG3
Step 1: Unpack kit contents. Download and install the latest kit setup le
"CY4501 CCG1 DVK COMPLETE SETUP" from www.cypress.com/go/CY4501
CCG1 CLIENT BOARD
CCG1 EMCA BOARD
NOTE: 1. The Type-C receptacles and plugs used on the CCG1 boards are delicate parts and they
need to be handled carefully. Avoid putting excess pressure on the Type-C receptacles
and plugs during usage
2. Board revision number etched on the PCBA may differ from the image shown above.

QUICK START GUIDE
Step 2: Verify jumper settings on the CCG1 Host board. Use SuperSpeed USB Type-A to Type-B
cable to connect a PC with the Host board's SuperSpeed USB Type-B connector
(receptacle) J12.
J4, Decides the 5 V Power Source
for the Board
1-2: Power from MiniProg3
2-3: Power from USB Type-C
Connector
2-4: Power from J3 USB Mini-B
Connector
2-5 : Power from J12 USB
SuperSpeed Connector (Default)
J6, Provision for Measuring
Current Consumption on VCONN
(Default Short)
J8, CC2 Rp Selection for Current
Advertisement
1-2: 900 mA for USB SS
2-4: 1.5 A (Default Setting)
2-3: 3.0 A
J10, CC1 Rp Selection
for Current Advertisement
1-2: 900 mA for USB SS
2-4: 1.5 A (Default Setting)
2-3: 3.0 A
SW2, CCG1 Reset Switch
J11, Provision for Measuring
Current Consumption of CCG1
(Default Short)
Step 3: Verify jumper settings on the CCG1 Client board. Using a USB 2.0 Type-A to Mini-B cable,
connect a PC to the USB Mini-B connector J7 of the Client board to provide power.
J5, J6, Rp Selection on CC2
and CC1
1-2: 900 mA for USB SS
2-4: 1.5 A (Default Setting)
2-3: 3.0 A
24 V Power Jack
J3, Decides the Power Source
1-2 and 3-4 Shorted: Power from
Type-C Connector
5-6 and 7-8 Shorted: Power from
24 V Power Jack (Default Short)
J12, Provision for Measuring
Current Consumption of CCG1
(Default Short)
SW2, CCG1 Reset Switch
J10, Provision for Measuring
Current Consumption on
VCONN (Default Short)
J11, Decides the Power Source
1-2: Power from MiniProg3
2-3: 5 V power regulated from 24 VDC,
Also see J3 settings.
2-4: Power from J7 USB Mini-B
Connector (Default)

QUICK START GUIDE
Step 4: Verify jumper settings on the CCG1 EMCA board.
Step 5: Connect one end of the EMCA board to the Host board and its other end to the Client board.
Plug a USB drive (not provided with the kit) into the Client board. Verify your setup as shown
in the picture below. To evaluate SuperSpeed USB data transfers, it is recommended to use
a SuperSpeed USB ash drive.
5 V Power
(Mini USB Cable)
USB Flash Drive
CCG1
EMCA Board
CCG1
Client Board
CCG1 Host Board
USB SS
Type-A to
Type-B Cable
J2, Controls Disconnection of
VCONN Ra Resistor for J14
Type-C Connector
1-2 Short: U2 (Near End CCG1)
Controls Disconnection
2-3 Short: U1 (Far End CCG1)
Controls Disconnection
(Default Setting)
J7, U2 VDD Power Selection.
1-2 Short: U2’s VDD Connects
to VCONN_COM
2-3 Short: U2’s VDD Connects to
J14’s (Type-C Connector VCONN)
Open: Default Setting
J6, U1 VDD Power Selection
1-2 Short: U1’s VDD Connects to
VCONN_COM (Default Setting)
2-3 Short: U1’s VDD Connects to J1’s
(Type-C Connector) VCONN
J3, Controls Disconnection of
VCONN Ra Resistor
for J1 Type-C Connector
1-2 Short: U1 (Near End CCG1)
Controls Disconnection (Default Setting)
2-3 Short: U2 (Far End CCG1)
Controls Disconnection

© 2015-2017 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the properties of their respective owners.
001-96648 Rev.*C
QUICK START GUIDE
CY4501 CCG1 DVK
For the latest information about this kit, visit www.cypress.com/go/CY4501
Step 6: Observe enumeration of the USB drive connected to the Client board on the PC connected to
the Host board. Observe the SuperSpeed USB data transfer speed by transferring large les.
Step 7: Disconnect the EMCA board from host and client boards. Repeat the connection sequence in
Step 5 with the EMCA board ipped upside down.
Step 8: Observe enumeration of the USB drive connected to the Client board on the PC connected
to the Host board even with the EMCA board ipped. Also, observe the SuperSpeed USB data
transfer speed by transferring large les. This demonstrates orientation adjustment of the
Type-C interface. This step can be repeated with the EMCA board in any other orientation.
Step 9: For more details, refer to the CY4501 CCG1 Development Kit Guide.pdf located at
C:\Program Files (x86)\Cypress\CY4501 CCG1 DVK\1.0\Documentation for 64-bit
Windows operating systems or C:\Program Files\Cypress\CY4501 CCG1 DVK\1.0\
Documentation for 32-bit Windows operating systems.
5 V Power
(Mini USB Cable)
USB Flash Drive
CCG1 Client Board
CCG1 Host Board
USB SS
Type-A to
Type-B Cable
CCG1 EMCA Board