Cypress Semiconductor CY8CKIT-062S2-43012 User manual

CY8CKIT-062S2-43012 QUICK START GUIDE
PSOC®62S2 WiFi BT PIONEER KIT
Kit Contents:
1 PSoC®62S2 Wi-Fi BT Pioneer Board
2 USB Type-A to Micro-B cable
3 Four jumper wires (four inches each)
4 Two jumper wires (ve inches each)
5 Quick Start Guide (this document)
www.cypress.com/CY8CKIT-062S2-43012
• PC with USB port
•UART terminal software such as Tera Term
or Minicom
•Visit the kit website to download and install the
required software
•Ensure the jumper J14 is at position 2-3 to select 3.3V
•Connect the KitProg3 USB connector (J6) to your PC
•Wait for the drivers installation to complete
•Open the UART terminal software and connect to
the kit's USB-UART COM port with the settings
– Baud rate: 115200, Data: 8 bit, Parity: None, Stop
bit: 1 bit, Flow control: None
•Press the XRES switch (SW1) to reset the device
•Follow the instructions displayed on the UART
terminal to use the pre-programmed code example
Refer to the Kit Guide available at the kit website
for details.
• Before starting, ensure you have the following.
1 2

© 2019 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the property of their respective owners.
002-28145 Rev*B
For the latest information about this kit, visit www.cypress.com/CY8CKIT-062S2-43012
CY8CKIT-062S2-43012 QUICK START GUIDE
PSoC 62S2 Wi-Fi BT Pioneer Kit Details
Arduino Uno R3
LEGEND
PSoC 6 I/Os
WL/BT I/Os
NC
VTRAG/IOREF
XRES/RESET
V 3.3/3.3V
V 5.0/5V
GND/GND
GND/GND
VIN/Vin
P6_0/SCL
P6_1/SDA
VREF/AREF
GND/GND
P12_2/D13
P12_1/D12
P12_0/D11
P12_3/D10
P7_6/D9
P7_5/D8
P5_7/D7
P5_6/D6
P5_5/D5
P5_4/D4
P5_3/D3
P5_2/D2
P5_1/D1
P5_0/D0
P1_4
P0_4
P7_4
NC
NC
NC
NC
NC
NC
NC
NC
P13_5
P13_4
P8_0
P13_6
P1_3
P0_3
P0_2
P10_0/A0
P10_1/A1
P10_2/A2
P10_3/A3
P10_4/A4
P10_5/A5
P10_6
P10_7
P9_0
P9_1
P9_2
P9_3
P9_4
P9_5
P9_6
P9_7
BT_UART_RXD
BT_UART_TXD
BT_UART_CTS
BT_UART_RTS
WL_UART_RX
WL_UART_TX
WL_IO1
WL_IO2
P7_3
P0_5
P1_1
NC
P11_1
P1_5
BT_I2S_CLK
BT_I2S_WS
BT_I2S_DO
BT_I2S_DI
BT_IO2
BT_IO3
BT_IO4
BT_IO5