Cypress CLUX-22HC User manual

CLUX-22HC
HDMI/CAT6 to HDMI/
CAT6 Splitter Switcher
Operation Manual
CLUX-22HC

Disclaimers
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes
no commitment to update or to keep current the information
contained in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
Copyright Notice
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
- electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise - without express written permission and consent from
Cypress Technology.
© Copyright 2009 by Cypress Technology.
All Rights Reserved.
Version 1.0 December 2009
Trademark Acknowledgments
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.

Safety Precautions
Please read all instructions before attempting to unpack or install or
operate this equipment, and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
 Always follow basic safety precautions to reduce the risk of
fire, electrical shock and injury to persons.
 To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
 Never spill liquid of any kind on or into this product.
 Never push an object of any kind into this product through
module openings or empty slots, as you may damage parts.
 Do not attach the power supply cabling to building surfaces.
 Do not allow anything to rest on the power cabling or allow it to
be abused by persons walking on it.
 To protect the equipment from overheating, do not block the
slots and openings in the module housing that provide
ventilation.
Revision History
Version No Date Summary of Change
V1 20091208 Preliminary Release

Table of Contents
1
1
1
1
2
3
4
4
5
6
7
9
1. Introduction…………………………………………………........……….
2. Applications……………………..…………………………................….
3. Package Contents…………………………......…………….............…
4. System Requirements……...…………………..….…………........…….
5. Features…………………………………………….......……........………
6. Specications..………………………………………...........………...….
7. Operation Controls and Functions………………...……........………
7.1 Front Panel ...............................................................................
7.2 Rear Panel……………......………………………….........…….…
8. RJ-45 Pin Denitions …….………………….......................…..…..…...
9. Connection and Installation.............................................................
10. Acronyms...........................................................................................

1. Introduction
The HDMI/CAT6 to HDMI/CAT6 Splitter Switcher is the most advanced
solution for HDMI and Video/DDC signal distribution. This CAT6 output port
can be easily connected to an HDMI receivers CAT6 input port to allow a
stable connection between an HDMI source and any compatible display.
Each product in this series is compatible to HDMI V1.3, which defines and
supports the transfer of Deep Color (10bit and 12bit) video and a new
lossless compressed (Dolby TrueHD, Dolby Digital Plus and DTS-HD Master
Audio) digital audio signal, with a high bandwidth up to 225MHz (6.75Gbps).
Besides splitting and distributing, the Video/DDC CAT6 output also does signal
amplification and equalization which provide high performance I/O of audio
and video.
2. Applications
 Home entertainment integration
 Multi-task project presentation
 Showroom Display
 Advertising display control
 System installation control
3. Package Contents
 1 x HDMI/CAT6 to HDMI/CAT6 Splitter Switcher
 5V DC power supply adaptor
 User Manual
4. System Requirements
 Input source equipment(s) with HDMI cable and or HDMI to CAT6 transmitter
 Output display(s) with HDMI cable and or CAT6 to HDMI receiver with
HDMI cable to display
1

5. Features
 HDMI 1.3, HDCP1.1 and DVI1.0 compliant.
 Deep color video up to 12bit, 1080p@(24/60)Hz.
 Simultaneously outputs one HDMI and one Video/DDC CAT6 source to
one HDMI and one Video/DDC CAT6 output.
 HDCP keysets allows each output to work independently when
connecting to an HDMI display.
 Capable of splitting HDMI/CAT6 sources to HDMI/CAT6 outputs without
any signal loss.
 Supports LPCM7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD
master audio transmission (32-192 kHz Fs sample rate).
 Supports a wide range of PC and HDTV resolutions from VGA to SXGA
and 480i to 1080p.
 Full HDCP Compliant.
 According to tests The Input/Output source can be up to 15/15 meters
away when the HDMI cable has a resolution of with 1080p/8bits. The
CAT6 cable test showed that with a resolution of 1080p/8bits, the Input/
Output source can be 45/45 meters away. The HDMI cable test showed
that with a resolution of 1080p/12bits, the Input/Output source can be
15/10 meters away. And finally the CAT6 cable test showed that with a
resolution of 1080p/12bits, the Input/Output source can be 20/20 meters
away
2

Bandwidth Frequency 2.25Gbps (single link)
Input Ports 1 x HDMI female port (Type A connector)
1 x CAT6 input Video/1 x CAT6 input DDC
Output Ports 1 x CAT6 output Video/1 x CAT6 output DDC
1 x HDMI female ports (Type A connector)
EDID STD / TV
HDMI Audio Output PCM2, 5.1, 7.1, Dolby 5.1, DTS 5.1, DD+, D-TrueHD,
DTS-HD
HDMI Cable In 1080p 8-bit (15M), 12-bit (15M)
HDMI Cable Out 1080p 8-bit (15M), 12-bit (10M)
CAT6 Cable In 1080p 8-bit (45M), 12-bit (20M)
CAT6 Cable Out 1080p 8-bit (45M), 12-bit (20M)
HDMI Resolution 480i, ~ 1080p 50/60, 1080p 24, VGA ~ SXGA
IR Frequency 20 ~ 60KHz
ESD Protection Human body model: ±8kV (air-gap discharge)
±4kV (contact discharge)
Power Supply 5VDC/3.2A (US/EU standards, CE/FCC/UL certified)
Dimensions (mm) 215(W) x123(D) x 30(H)
Weight(g) 365
Chassis Material Metal
Silkscreen Color Silver
Power Consumption 4.1W
Operating Temperature 0˚C ~ 40˚C / 32˚F ~ 104˚F
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (non- condensing)
6. Specications
3

7. Operation Controls and Functions
The following sections describe the hardware components of the unit.
7.2 Front Panel
1 2 3 4 65
①HDMI/CAT6 input selection: Switch to select input sources from either
HDMI or CAT6.
②EDID Control Switcher: The default factory setting is TV, do not switch if the
display is compatible. Switch to STD to use built-in EDID.
[Note]:
1. When EDID is switched to TV, the unit will detect and record the first HDMI’s
output EDID in the unit. If the first detected HDMI output is DVI it will
continue to pass on to the next output until the first HDMI output is found.
The detection priority is HDMI v1.3 > HDMI v1.2 > DVI.
2. When EDID is switched to STD the unit will use its own EDID which supports:
Video →1080p 8-bit (max)
Audio →PCM 2CH
3. When EDID is switched to STD with input selection on HDMI or CAT6 IN the
display TV or monitor, they will automatically switch to HDMI input 1. When
EDID is switched to TV regardless of the input selection the display TV or
monitor will switch to HDMI input mode 1. Therefore it is not suggested to
switch the EDID to STD.
4. The EDID selection will activate only when the unit is plugged in and power
is on.
③CEC output: Only when switched to HDMI, the HDMI’s output port CEC will
bypass the CEC and proceed directly to the HDMI and CAT6 input ports.
When switched to HDMI and CAT6, the HDMI and CAT6 output ports CEC
will bypass the CEC and go proceed directly to the HDMI.
④HDMI Input: Connect input port to the HDMI or DVI output port of your
4

source equipment such as DVD player or set-top-box.
⑤CAT6 IN: These slots are for connecting the Video/DDC input to the
Video/DDC output of the transmitter unit with CAT6 cables.
[Note]:
1. Cable tested with CAT-6E / 23AWG / was solid, so any cables with
different specifications might result in a different distance.
2. The cable distance was tested with a PS3 40G and 37" SamSung 12
bits LCD TV.
3. The figures provided in this manual are for reference use only, actual
results depend on your specific configuration, i.e.: your source and
display and type of cabling used.
⑥DC 5V: This is the slot where you insert the 5V DC power supply for
electrical power before plugging the adaptor into an AC wall outlet.
7.1 Rear Panel
1 2
3
4
5
6
①CAT6 OUT: Connect the Video/DDC output to the Video/DDC input of
the receiver unit using CAT6 cables.
②HDMI OUT: Connect HDMI output port to the HDMI display.
③HDCP indicators: When the input source has HDCP protection the HDCP
LED will turn on.
④The LED light will turn when the HDMI or DVI source has been connected.
⑤HDMI/CAT6 input indicator: The LED light will turn on when the HDMI or
CAT6 source has been selected.
⑥Link OUT: The LED light will turn on when the display has been connected.
5