Czur Aura Mate User manual

User Manual
CZUR TECH CO., LTD.
9F, North Wing, West Block, PKU-HKUST ShenZhen-HongKong Institution,
Gaoxin South 7th Road, Nanshan District, Shenzhen, China
Room1001,10th Floor, Block A, No.32A Huoju Road, High-tech Industrial
Zone, Dalian City, Liaoning Province, China
E-Mail: [e-mail] Skype: [e-mail]
www.czur.com
User Manual
CZUR TECH CO., LTD.
9F, North Wing, West Block, PKU-HKUST ShenZhen-HongKong Institution,
Gaoxin South 7th Road, Nanshan District, Shenzhen, China
Room1001,10th Floor, Block A, No.32A Huoju Road, High-tech Industrial
Zone, Dalian City, Liaoning Province, China
E-Mail: [e-mail] Skype: [e-mail]
www.czur.com

Chapter I Product Introduction
1.1 Overview ................................................................... 2
1.2 Product Dimensions .....................................................2
1.3 Product External View .................................................. 3
1.4 Product Parameters .................................................... 5
1.5 Packaging and Accessories ...........................................5
Chapter II Operation Instructions
2.1 Connect Device to Network ................................ . .........6
2.2 Table Lamp Mode .......................................................6
2.3 Sitting Posture Reminder ............................................6
2.4 Video Call ...................................................................7
2.5 Scanner Function ........................................................7
Chapter III FAQs and Troubleshooting
3.1 Video Call .................................................................9
3.2 Scan ........................................................................9
3.3 Table Lamp ...............................................................11
3.4 Sitting Posture Reminder ...........................................11
Chapter IV Service and Statement
4.1 After Sales Services and Warranty ...............................12
4.2 Contact ................................................................... 13
Contents
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
（1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Connect the equipment into an outlet on a circuit different from that to which the
· Consult the dealer or an experienced radio/TV technician for help.
1.
2.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator.
The symbol indicates DC voltage.
RECYCLING:This product bears the selective sorting symbol for Waste electrical and
electronic equipment ( WEEE ). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or dismantled to
minimize its impact on the environment.
FCC STATEMENT
FCC Radiation Exposure Statement
receiver is connected.

Chapter I Product Introduction
1.2 Product Dimensions
2
1.1 Overview
Aura Mate is a brand new scanner. It is configured with high-performance ARM 4-core
Cortex-A17 CPUs, high-definition sensors, uniform optics and network connection, and
other hardware. It can be used as a table lamp that is radiation-free, has low-frequency
flashing, uniform light, multiple modes, as well as functions such as video call, sitting
posture reminder, and high-definition scanning. It is suitable for office, family and
individuals, teachers and students, and education and training industry.
The video call function allows real-time video chats as office meeting and between
parents and children, and teachers and students, which can facilitate timely
communication between the two parties and remote to solve problems in a timely
manner.
The sitting posture reminder function reminds users to sit properly and prevents their
eyesight and neck from being affected.
The table lamp function can be controlled by the knob on the device or the APP on your
smart phone. There are four table lamp modes: eye protection, computer, reading &
writing, and natural light.
The device supports smart position correct, auto-cropping of scanned images, and
multiple color modes optimizing. You may scan learning materials, books, test papers,
archives, receipts, etc, and upload the scanned images to the cloud. Then You can view,
edit, or share the images through the APP.
443.82
180.96
372.84
341.70
Unit: mm

Note:
4
1.3 Product External View
1
2
3
4
5
7
6
3
2、3、4、 5: holder, base, camera casing, LED light, display module
HD CMOS camera
Knob switch
Press: press the knob to turn on/off the table lamp
Turn: turn the knob clockwise to enhance the brightness or anti-clockwise to reduce
the brightness.
Microphone
LCD screen
Speaker
Video camera indicator
Video camera
Cooling holes
Networking button
Power indicator
The device starts automatically and the indicator is on when the device is connected
to power supply.
Wi-Fi indicator
The indicator is off when the device is disconnected to the network.
The indicator is on when the device is connected to the network.
The indicator flashes and then is off when the network is abnormal.
Touch button for video call
Video call indicator
The indicator is shimmery when the video call function is available.
The indicator is bright when the video call is going on.
Touch button for scanning
Scanning indicator
The indicator is shimmery when the scanning function is available.
The indicator is bright when the scanning is going on.
Reset button
Press the reset button to restart the device.
Type A USB Port for connecting foot pedal
Type B USB Port for connecting computer
DC Port for connecting power adapter (9V 1.5A)
Foot pedal
1、
6、
7、
8、
9、
10、
11、
12、
13、
14、
15、
16、
17、
18、
19、
20、
21、
22、
23、
24、
25、
8
15
16
17、18
19、20
9
10
12
13
14
11
21
22
23
24
25

Chapter II Operation Instructions
2.1 Connect Device to Network
This device is configured and controlled by APP. Please
download the APP from our official website:
https://www.czur.com, or you can scan the QR code to
download the APP.
Install and run the "CZUR" APP, scan the QR code, and then
connect the device to the network by following the instructions.
2.2 Table Lamp
1. Plug in the power adapter to connect the device to power supply, and the device starts
automatically. Press the knob and the table lamp is on.
2. Turn the knob to control the brightness of the table lamp.
3. When the device is connected to the network, you can control the device by the CZUR
APP.
2.3 Sitting Posture Reminder
1. Plug in the power adapter to connect the device to power supply, and then the device
starts automatically.
2. When the device is connected to the network, you can enable or disable the
sittingposture function by the APP.
1) Control the table lamp function by your smart phone (you can turn on or off the table
lamp or adjust its color temperature mode).
2) There are four table lamp modes: eye protection, computer, reading & writing, and
natural light. You can turn the table lamp on or off and adjust the brightness.
3) There are six levels of brightness for each color mode. Turn the knob clockwise to
enhance the brightness or anti-clockwise to reduce the brightness. The brightness
will be resumed to the default level each time you change the mode.
1.5 Packaging and Accessories
Name
Main device
Foot pedal
Power adapter
Specification
Aura Mate Pro
USB port, cable length 2.0 m
Input AC: 100-240V 50/60HZ 0.6A
Output DC: 9V 1.5A
Quantity (pcs)
1
1
1
6
1.4 Product Parameters
Sensor :16 Mmegapixels
Highest resolution 4608*3456
Scanning format: ≤ A3; scanning speed ≈ 1.0 s
Video format: MJPG
Picture format: JPG
Export format: PDF/WORD/EXCEL/Searchable PDF
ARM 4-core Cortex-A17
Camera for scanning, 16 megapixels
Camera for video call, 2 megapixels
2.4 '' LCD screen
Basic
configuration
Processor
Camera
LCD screen
Natural light (110-800 lx), reading and writing
(110-880 lx), computer (160-630 lx), eye-protection
(115-850 lx)
Natural light (4800K), reading and writing (4000K),
computer (3000K), eye-protection (3900K)
Cloud storage and management of images, smart
position correct and auto-cropping of images
Remote view, video call transfer
Sensitivity levels: High, medium, low
Control by knob, remote control by APP
Table lamp
mode and
brightness
Color
temperature
of table lamp
Eye-protection
table lamp
Scan
Video call
Sitting posture
reminder
Parameters
Features
5
Soft pad
User Manual
Finger cots
Getting Started
Guide
CD
USB cable
530 × 415 ×1.8 mm
Color printing, 126 × 176 mm
Left hand, right hand
105 g, 100 × 83 mm color printing
CD-R, D = 120 mm
USB port, cable length 1.5 m
1
1
2
1
1
1
1.
2.

2.4 Video Call
1. Plug in the power adapter to connect the device to power supply, and then the device
starts automatically.
2. When the device is connected to the network, you can start a video call through the
device or by the CZUR APP.
2.5 Scanner Function
2.5.1 Scanning by APP on Your Phone
2.5.1.2 Function Introduction
2.5.2 Scanning by Client software on Computer
2.5.2.2 Function Introduction
2.5.2.1 Preparation
2.5.1.1 Preparation
1) Video call initiated by device: Tap the video call icon on the device, call the
mobile phone bound with the device. When the phone user answers the call, you can
see the phone user through screen on the device.
2) Video call initiated by phone: Tap the icon in the interface. The device will
receive the call and will answer the call automatically in 5 seconds.
1) Tap the icon to enable the scanning function. Check whether the LCD screen
is fully covered by the black soft pad (The black soft pad must be properly placed,
which is crucial for the algorithm function; otherwise, image processing error may
occur).
2) Press the foot pedal to start scanning.
1) Check whether the screen is fully covered by the black soft pad through preview area
of the client end on the computer (The black soft pad must be properly placed,
which is crucial for the algorithm function; otherwise, image processing error may
occur).
2) Click the scan button on the client end of the computer or press the foot pedal to
start scanning.
1. Connect the device to power supply and the device will
start automatically.
2. Scan the QR code to connect the device to the network.
3. Connect the foot pedal to the device base.
4. Unfold the black soft pad, align and connect the notch
with the device base properly. Unfold the device until
the camera casing is 90° to the base (see the figure).
5. Notes
7 8
1) Tap the "Sitting Posture reminder" icon to enter the
sitting posture reminder interface.
2) Enter the "Record Standard Sitting Posture". When the user is sitting properly in front
of the device, press the record button to record the sitting posture into the device.
3) The user can adjust the volume of the voice reminder and the sensitiveness of the
reminder by the APP.posture function by the APP.
1. Tap the scan icon on the device to enable the scanning function. You can see the
preview image on the LCD screen.
2. Press the foot pedal with your foot to start scanning. The screen will display "scanned
N images", "uploading N images".
3. Open the APP, tap the file icon in the lower right corner to enter the file management
interface, and you can view, edit, or sort the images that have been uploaded.
1. Connect the device to power supply and the device
will start automatically.
2. Connect the device to a computer with the USB cable.
3. Connect the foot pedal to the device base.
4. Unfold the black soft pad, align and connect the
notch with the device base properly. Unfold the
device until the camera casing is 90 ° to the base (see
the figure).
5. Notes
1. The default brightness of the LED light is at the brightest level. Turning the knob
clockwise or anti-clockwise can adjust the brightness at six levels.
2. Open the client software on the computer, click the scan icon at the lower right corner
to enter the scan interface. Select a color mode or processing mode on the right side.
Click the scan icon and start scanning (Select a proper processing mode; otherwise,
the scanning may be affected).
Sitting Posture reminder

1) Check whether the power socket is connected to power supply and whether the
power adapter is properly connected.
2) Check whether there is a power failure or abnormal operation during the automatic
firmware upgrade process. Please contact customer service if the firmware upgrade
fails (contact information is listed on the last page of this document).
10
1. The device cannot start and the power indicator is off.
4. There is no image in the file management of the APP.
5. The CZUR software cannot be installed or errors occur during the installation in a
computer.
6. The SN is incorrect.
7. When use Aura Mate and open the software for the first time on a computer, there is
no image, and the scan function does not work.
3.1 Video Call
Chapter III FAQs and Troubleshooting
1) Check whether the power socket is connected to power supply and whether the
power adapter is properly connected.
2) Check whether there is a power failure or abnormal operation during the automatic
firmware upgrade process. Please contact customer service if the firmware upgrade
fails (contact information is listed on the last page of this document).
1) Make sure that the black soft pad's notch is properly connected to the base, and the
scan preview area is fully covered by the pad. Refer to section 2.1.1 in Chapter II.
2) The materials to be scanned shall be placed within the preview area. "Materials to be
scanned" include test papers, homework, books, ID documents, files, and 3D objects.
1) Unplug and replug the USB cable of the foot pedal, or restart the device.
2) Check whether the device is connected to the network.
1. The device cannot start and the power indicator is off.
3. There are problems, such as distortion and deformation of images, or words on the
images being stretched.
2. The scanning function does not work when pressing the foot pedal.
3.2 Scan
1) Check whether the device is connected to the network.
2) Check whether the video call touch button indicator is on with shimmery light.
3) Touch the button again to restart the video call.
2. Video call fails.
9
3) Check whether there are any other objects except the "materials to be scanned".
Such objects may affect the algorithm and the scanning effect. For example, erasers,
phones, and pens.
1) Pull down to refresh the interface.
2) Check whether the images have been uploaded through the number displayed on
the LCD screen.
3) Check the network condition of your phone.
4) Check whether the device is connected to the network.
1) XP, Win7, Win8, Win10, and Mac OS are supported.
2) Check whether the SN is correct.
3) Check and enable the anti-virus software and firewall on your computer. Close the
anti-virus software or add trust. Close the firewall or lower the security level.
4) If you download the software at the official website, please ensure that the software
has been downloaded and then install it.
1) Replug the USB cable, restart the device or restart the client end on the computer.
2) Use another USB port of the computer, for the performance of each USB port of the
computer is different.
3) Exit anti-virus software, security guards, or defensive back-end software.
4) Check if the "Device Manager" of the computer recognizes the client end on the
computer. If a yellow exclamation mark/unknown device appears, right click to
update the driver or disable it first and then turn it on, and then restart the software.
5) Use the "Device Manager" of the computer to disable other "Scanner", "Monitor", or
"Camera".
Check whether you have entered a correct SN. Letters and numbers shall be
distinguished. There is no "1" in any SN.

12
1. The device cannot start and the power indicator is off.
2. The CZUR APP is unable to control the table lamp.
1. The device cannot start and the power indicator is off.
2. There is no voice reminder.
3. The brightness of the table lamp cannot be adjusted.
1. All after sales policy of this product shall be subject to the laws and regulations of the
country. You may return the device within seven days after receiving the device if there
is quality issue. We offer one-year warranty.
2. The scope of warranty covers the scanner. Consumables and external view are not
covered in the warranty.
3. We apologize for not issuing notices for subsequent upgrades or version updates of the
product. CZUR reserves the right of final decision on the interpretation of the above
articles.
4. Exceptions to Warranty
Chapter IV Service and Statement
1) Check whether the power socket is connected to power supply and whether the
power adapter is properly connected.
2) Check whether there is a power failure or abnormal operation during the automatic
firmware upgrade process. Please contact customer service if the firmware upgrade
fails (contact information is listed on the last page of this document).
1) Check whether the device is connected to the network.
2) Check whether the device is connected to the server. The device status is displayed in
the upper left corner on the current page of the APP. If the status is offline, it means
that the device is not connected to the server. If the status is online, it means that the
device is connected to the server, and you can control the table lamp with the APP.
1) Check whether the power socket is connected to power supply and whether the
power adapter is properly connected.
2) Check whether there is a power failure or abnormal operation during the firmware
upgrade process. Please contact customer service if the firmware upgrade fails
(contact information is listed on the last page of this document).
1) Check whether the table lamp is used by another user.
1) This product can only be used in areas where the surrounding temperature is less
than 40℃.
2) Failures or damages caused by incorrect installation or using the product in
environments that exceed the specified work conditions (for examples, in places
that are too hot or too humid).
3) Damages caused by using components not from our company or when users replace
components by themselves.
4) Damages caused by natural disasters, accidents, or human factors.
5) Damages caused by inappropriate storage (including damages caused by rats or
liquid infiltration).
6) Failures or damages caused by unauthorized repairs, modifications, or abuse carried
out by users.
Dear user, thank you for using CZUR scanner. To protect your legal rights, please peruse
and comply with the following standards and statements.
1) Check whether the voice function is enabled. If not, connect the device to the
network and then enable the function in the CZUR APP.
2) Check whether the video call camera is on, and whether the video call camera
indicator is on.
Check whether the brightness is at the highest or lowest level. If it is at the highest level,
the brightness cannot be higher, and if it is at the lowest level, the brightness cannot be
lower.
3.3 Table Lamp
4.1 After Sales Services and Warranty
3.4 Sitting Posture Reminder
3. The device keeps reminding the user about the sitting posture.
11
2) Check whether the positions of the table lamp and the user have been changed.
3) Record new standard sitting posture in the device if the table lamp is used by
another user or if the positions of the table lamp and the user have been changed.

14
13
Get technical support and information by the following ways.
Firstly, you can contact local distributors if you know them. Secondly, you can contact us
directly.
CZUR TECH CO., LTD.
9/F, North Wing, West Block, Shenzhen-Hong Kong Institution, High-Tech South 7th Rd.,
Nanshan District, Shenzhen, China.
Room 1001, Building A, Chuangye Mansion, No. 32A Huoju Road, High-Tech District,
Dalian, China.
Manufacturer: CZUR TECH CO., LTD.
After-sales Address: 2/F, Building 2, Baoshi Technology Park, No. 12, Baoshi Road,
Jiaoyitang Village, Tangxia Township, Dongguan City, Guangdong
Email: [e-mail]
Web: www.czur.com
4.2 Contact
7) Damages caused by repairs carried out by unauthorized repair centers.
8) Other errors and failures caused by software installation or software settings, or
problems and failures caused by computer viruses.er have been changed.