D-Link DSH-G200 User manual

DSH-G200 D-Link Corporation
Page 1
DSH-G200
Omna Z-Wave Bridge
User’s Manual
Version 1.0
May. 12th, 2017

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Note The country code selection is for non-US model only and is not available to all US
model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation

channels only.
Industry Canada statement:
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes (1) le dispositif ne doit pas
produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y
compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the
potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such
that the equipment still complies with the e.i.r.p. limits specified for point-to-point and
non-point-to-point operation as appropriate; and
(iii) Users should also be advised that high-power radars are allocated as primary users (i.e.
priority users) of the bands 5650-5850 MHz and that these radars could cause interference
and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
(ii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5725 à 5 850 MHz)
doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et
l’exploitation non point à point, selon le cas;
(iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute
puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes
5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux
dispositifs LAN-EL.

Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.
低功率電波輻射性電機管理辦法
低功率電波輻射性電機管理辦法低功率電波輻射性電機管理辦法
低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，
並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
「電磁波曝露量MPE標準值1mW/cm
2
，本產品使用時建議應距離人體 20 cm」

DSH-G200 D-Link Corporation
Page 2
Table of Contents
1. PRODUCT DESCRIPTION..................................................................................3
2. APPEARANCE .....................................................................................................3
3. APPLICATIONS...................................................................................................4
4. INSTALLATIONS & BASIC CONFIGURATIONS ...........................................4

DSH-G200 D-Link Corporation
Page 3
1. PRODUCT DESCRIPTION
The DSH-G200 is a Z-Wave smart home bridge supporting S2 security and
working with Apple HomeKit app to manage Z-Wave nodes to communicate
with other HomeKit related devices.
2. APPEARANCE
Top
LED: Status indicator
Wireless button: Z-Wave pairing/un-pairing
Rear
LAN port x1
Micro USB: Power jack, 5V/1.A or 1.2A
Bottom
Reset button
Mounting installation

DSH-G200 D-Link Corporation
Page 4
3. APPLICATIONS
4. INSTALLATIONS & BASIC CONFIGURATIONS
Step 1 Make sure your DSH-G200 is powered on and near by your iOS devices.
Step 2 Open Home and tap “Add Accessory”or tap to add the DSH-G200 to
your home.

DSH-G200 D-Link Corporation
Page 5
Step 3 Wait for the DSH-G200 to appear, then tap it. (Note: If asked to Add
Accessory to Network, tap “Allow”.)
Step 4 Scan the eight-digit HomeKit code on the DSH-G200 or its documentation. Or
enter the code manually.
Step 5 Add information about your DSH-G200, like its name or the room it's located
in. Siri will identify the DSH-G200 by the name you give it and the location
it's in.
Step 6 Tap “Next”, then tap “Done”to finish the setup.
Note:
1. Press the wireless button to enter inclusion mode to include Z-Wave nodes.
2. Press the wireless button for more than 5 seconds to enter exclusion mode to
remove Z-Wave nodes.