D-Link D DI-707P DI-707P User manual

1
This product can be set up using
a current java-enabled web
browser, i.e., Internet Explorer or
Netscape Navigator.
DI-707P
Ethernet Broadband
Router and Print Server
5V DC Power Adapter
©2003 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective holders. Software and
specifications subject to change without notice. DI-707P.08082003
Before You Begin
1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-707P Broadband Router. The DI-707P acts as a DHCP server and will assign
all the necessary IP address information on your network. See Appendix at the
end of this Quick Installation Guide or the Manual on the CD-ROM for setting
each network adapter to automatically obtain an IP address.
Check Your Package Contents
DI-707P Ethernet Broadband Router
CD-ROM (containing Manual and Warranty)
Ethernet (CAT5 UTP/Straight-Through) Cable
Using a power supply
with a different voltage
rating will damage and void
the warranty of this product.
If any of the above items are missing, please contact your reseller.

2
Connecting The DI-707P Broadband
Router To Your Network
B. WAN Port
This is for the connection
of an Ethernet cable to the
Cable or DSL modem
C. LAN Ports These
are the connections
for Ethernet cables to
Ethernet enabled
computers.
D. Printer Port You
can connect a
Printer to the
Parallel Port here.
A. First, connect the power adapter to the receptor at the back panel of the
DI-707P and then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B. 1. Power off your Cable or DSL modem; some devices may not have a on/off
switch and will require you to unplug the power adapter. Now, the DI-707P
should be powered on and the Cable / DSL modem should be turned off.
2. Cable / DSL modem (Power Off) – DI-707P (Power On)
Connect an Ethernet cable to the Ethernet jack located on the Cable / DSL
modem. After the Ethernet cable is securely connected, power on the Cable /
DSL modem by turning on the unit or plugging in the power adapter.
3. Cable / DSL modem (Power On) – DI-707P (Power On)
Insert the other end of the Ethernet cable to the WAN PORT on the back panel
of the DI-707P. The WAN LED light will illuminate to indicate proper connection.
If the WAN LED is not illuminated, please go back to step B1 and repeat the
instructions.
C. Insert an Ethernet cable to LAN port 1 on the back panel of the DI-707P and an
available Ethernet port on the network adapter in the computer you will use to
configure the DI-707P. The LED light for LAN Port 1 will illuminate to indicate
proper connection. (Note: The LAN Ports on the DI-707P are Auto-MDI/MDIX.
Meaning you can use a straight-through or crossover-Ethernet cable to the LAN
Ports.)
D. The parallel port on the DI-707P is used to connect printers only. Connect one
end of the printer cable to your printer and the other end to the DI-707P.
Reset Button
Pressing this button restores
the Router to its original factory
default settings.
A. Receptor for
Power Adapter.

3
Restart Your Computer
Connecting Additional Computers To
The DI-707P
Using additional Ethernet (CAT5 UTP) cables, connect your
Ethernet-equipped computers to the remaining Ethernet LAN ports
on the back panel of the DI-707P
WAN LED – a
solid light indicates
connection on the
WAN port. This
LED blinks during
data transmission.
LOCAL NETWORK
LEDs – a solid light
on the port indicates a
connection to an
Ethernet enabled
computer on ports 1-7.
This LED blinks during
data transmission.
POWER LED – a solid
light indicates a proper
connection to the
power supply.
M2 LED – a solid light indicates
that Internet connection has
been established.
M1 LED – will flash
consistently to indicate
that the DI-707P is
working properly.

4
When you have completed the steps in this Quick Installation
Guide, your connected network should look similar to this:
Using The Setup Wizard
The logon pop-up screen will appear.
Open your Web browser and
type “http://192.168.0.1” into the
URL address box. Then press the
Enter or Return key.
Type “admin” for the username and
leave the password field blank.
Click OK

5
The Setup Wizard (continued)
Once you have logged in, the Home
screen will appear.
You will see the following screens
Set up your new password.You have
the option to establish a password.
Click Run Wizard
Click Next
Click Next

6
The Setup Wizard (continued)
Select your Internet Connection.
You will be prompted to select the type
of Internet connection for your router.
If you are unsure of which
setting to select, please contact
your Internet Service Provider.
Click Next
Click Next
Choose your time zone from the drop
down list.

7
The Setup Wizard (continued)
If your ISP requires a Static IP
Address, and this option is selected,
then this screen will appear:
If your ISP uses PPPoE (Point-to-Point
Protocol over Ethernet), and this option
is selected, then this screen will appear:
(Used mainly for DSL Internet service.)
Enter the IP address information origi-
nally provided to you by your ISP. You
will need to complete all the required
fields.
Please be sure to remove any
existing PPPoE client software
installed on your computers.
Enter in the username and password
provided to you by your ISP.
If you selected Dynamic IP Address,
this screen will appear: (Used mainly
for Cable Internet service.)
Click the “Clone MAC Address”
button to automatically copy the
MAC address of the network
adapter in your computer. You can
also manually type in the MAC
address.
Click Next
Click Next
Click Next
This setup should be done on the computer
that is registered on the ISP’s network.

8
Your Setup is Complete!
Click Restart
Test Internet Connection.
You will be returned to the Home tab.
For additional settings or information,
refer to the Advanced, Tools, or Status
tabs on the web-management interface;
or to the Manual located on the CD.
Then relaunch your Web browser (i.e.,
Internet Explorer or Netscape Naviga-
tor), to link to your favorite Web site to
test your Internet connection.
Click to Exit

9
APPENDIX
Insert the installation CD-ROM into the CD-
ROM drive. The following window will be
shown automatically. If it is not, please run
“autorun.exe” on the CD-ROM.
Installing the Print Server Software
Wait until the following Welcome dialog
appears.
Select the destination folder.
Click Next
Click Install Windows
Printer Software
Click Next
Select your Windows
operating system

10
After rebooting your computer, the software installation procedure is finished.
Installing the Print Server Software (continued)
Configuring on Windows 98se/Me Platforms
After you finish the software installation
procedure, your computer will be capable of
network printing provided by the DI-707P. For
convenience, we call the printer connected to
the printer port of the DI-707P a printer server.
On a Windows 95/98 platform, open the
Printers window in the My Computer menu.
Click OK
Now, you can configure the print server of the
DI-707P:
Find out the corresponding icon of your printer
server, for example, the HP LaserJet 6L.
Right click on that icon, and then select
Properties.
The following screen appears:
Then, the setup program will begin to install
the programs into the destination folder.
When the following window is displayed.
Click Finish