D-Link DSR-150 User manual

Unified Services Router
CLI Reference Guide
Release 1.05
Building Networks for People
Small Business Gateway Solution
DSR-150 / 150N / 250 / 250N / 500 / 500N /
1000 / 1000N

CLI Reference Guide
Unified Services Router
D-LinkCorporation
Copyright © 2012.
http://www.dlink.com

Unified Services Router CLI Reference Guide
1
CLI ReferenceGuide
DSR-150/150N/250/250N/500/500N/1000/1000N
Unified Services Router
Version 1.05
Copyright © 2012
Copyright Notice
This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes
no representations or warranties with respect to the contents hereof and specifically disclaim
any implied warranties of merchantability or fitness for any particular purpose. The
manufacturer reserves the right to revise this publication and to make changes from time to
time in the content hereof without obligation of the manufacturer to notify any person of such
revision or changes.
Limitationsof Liability
UNDER NO CIRCUMSTANCES SHALL D-LINK OR ITS SUPPLIERS BE LIABLE FOR
DAMAGES OF ANY CHARACTER (E.G. DAMAGES FOR LOSS OF PROFIT, SOFTWARE
RESTORATION, WORK STOPPAGE, LOSS OF SAVED DATA OR ANY OTHER
COMMERCIAL DAMAGES OR LOSSES) RESULTING FROM THE APPLICATION OR
IMPROPER USE OF THE D-LINK PRODUCT OR FAILURE OF THE PRODUCT, EVEN IF
D-LINK IS INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. FURTHERMORE, D-
LINK WILL NOT BE LIABLE FOR THIRD-PARTY CLAIMS AGAINST CUSTOMER FOR
LOSSES OR DAMAGES. D-LINK WILL IN NO EVENT BE LIABLE FOR ANY DAMAGES
IN EXCESS OF THE AMOUNT D-LINK RECEIVED FROM THE END-USER FOR THE
PRODUCT.

Unified Services Router CLI Reference Guide
2
Table of Contents
Chapter 1. Introduction............................................................................................................................................8
1.1 Accessing the CLI.................................................................................................................8
Chapter 2. Basic commands available on the CLI.........................................................................................9
2.1 CONTEXT SENSITIVE HELP..........................................................................................9
2.2 AUTO-COMPLETION .........................................................................................................9
2.3 MOVEMENT KEYS.............................................................................................................. 9
2.4 DELETION KEYS .................................................................................................................9
2.5 ESCAPE SEQUENCES ...................................................................................................10
Chapter 3. Command Hierarchy in CLI ...........................................................................................................11
3.1 CLI commands can be divided into 4 categories:....................................................11
3.2 The router configuration is divided into 5 branches:...............................................11
Chapter 4. Global commands used in CLI .....................................................................................................12
Chapter 5. Show commands used in CLI.......................................................................................................13
Chapter 6. Utility commands used in CLI .......................................................................................................18
6.1 util system_check ping <ltip_address>........................................................................18
6.2 util system_check dns_lookup <ltdns>........................................................................18
6.3 util system_check traceroute <ltip_address>............................................................18
6.4 util system_check capturePackets start <ltinterface>............................................18
6.5 util system_check capturePackets download <ltfileName> <ltipAddr>............18
6.6 util cat <ltfileName>............................................................................................................19
6.7 util md5sum <ltfileName> ................................................................................................19
6.8 util copy <ltfileName1> <ltfileName2> .........................................................................19
6.9 util usb_test <ltipAddr> <ltfileName> ...........................................................................19
Chapter 7. Configure commands used in CLI...............................................................................................20
Chapter 8. Configuration commands under branch NET..........................................................................29
8.1 net bandwidth profile enable...........................................................................................29
8.2 net bandwidth profile add/edit.........................................................................................29
8.3 net bandwidth profile delete <row_id>.........................................................................29
8.4 net bandwidth traffic_selector add ................................................................................30
8.5 net bandwidth traffic_selector edit <ltrow_id>...........................................................30
8.6 net bandwidth traffic_selector delete <ltrow_id>......................................................31
8.7 net ddns wan1 configure ..................................................................................................31
8.8 net ddns wan2 configure ..................................................................................................31
8.9 net lan dhcp reserved_ip configure <ltmac_address>...........................................31
8.10 net lan dhcp reserved_ip delete <ltmac_address>.................................................32
8.11 net wan dhcpc configure ..................................................................................................32
8.12 net dmz configure ...............................................................................................................32

Unified Services Router CLI Reference Guide
3
8.13 net dmz dhcp reserved_ip configure <ltmac_address>.........................................33
8.14 net dmz dhcp reserved_ip delete <ltmac_address>...............................................33
8.15 net ethernet configure <ltinterface_name> ................................................................34
8.16 net lan ipv4 configure ........................................................................................................34
8.17 net lan ipv6 configure ........................................................................................................36
8.18 net lan ipv6 pool configure <ltipv6PoolStartAddr> ..................................................36
8.19 net lan ipv6 pool delete <ltipv6PoolStartAddr> ........................................................37
8.20 net intel_Amt server configure........................................................................................37
8.21 net intel_Amt_Reflector configure.................................................................................37
8.22 net ip_Aliasing server add................................................................................................ 38
8.23 net ip_Aliasing server edit <ltrow_id>..........................................................................38
8.24 net ip_Aliasing server delete <ltrow_id>.....................................................................38
8.25 net mode configure.............................................................................................................39
8.26 net ipv6_tunnel isatap add...............................................................................................39
8.27 net ipv6_tunnel isatap edit <ltrow_id> .........................................................................39
8.28 net ipv6_tunnel isatap delete <ltrow_id> ....................................................................40
8.29 net routing mode configure..............................................................................................40
8.30 net wan wan1 ipv4 configure ..........................................................................................40
8.31 net wan wan2 ipv4 configure ..........................................................................................48
8.32 net wan wan3 threeG configure.....................................................................................56
8.33 net wan mode configure ...................................................................................................57
8.34 net wan port_setup configure .........................................................................................59
8.35 net wan configurable_port configure............................................................................59
8.36 net wan wan1 ipv6 configure ..........................................................................................59
8.37 net wan wan2 ipv6 configure ..........................................................................................60
8.38 net routing ospfv2 configure <ltinterface> ..................................................................61
8.39 net routing ospfv3 configure <ltinterface> ..................................................................62
8.40 net port management configure <ltportName>.........................................................63
8.41 net wan pppoe configure..................................................................................................63
8.42 net routing protocol_binding add...................................................................................64
8.43 net routing protocol_binding edit <ltrow_id>..............................................................64
8.44 net routing protocol_binding enable <ltrow_id> .......................................................65
8.45 net routing protocol_binding disable <ltrow_id>.......................................................66
8.46 net routing protocol_binding delete <ltrow_id>.........................................................66
8.47 net radvd configure.............................................................................................................67
8.48 net radvd pool add..............................................................................................................67
8.49 net radvd pool edit <ltrow_id> ........................................................................................68
8.50 net radvd pool delete <ltrow_id> ...................................................................................68
8.51 net routing dynamic configure ........................................................................................68
8.52 net routing static ipv4 configure <ltname> .................................................................70
8.53 net routing static ipv6 configure <ltname> .................................................................70
8.54 net routing static ipv4 delete <ltname>........................................................................71
8.55 net routing static ipv6 delete <ltname>........................................................................71

Unified Services Router CLI Reference Guide
4
8.56 net tahi add-default-route <ltip_address>...................................................................71
8.57 net tahi add-route <ltip_address> <ltgw>...................................................................71
8.58 net tahi del-route <ltip_address> <ltgw>.....................................................................72
8.59 net tahi ipv6-Alias-Add(LAN) <ltip6_address>..........................................................72
8.60 net tahi ipv6-Alias-Del(LAN) <ltip6_address>...........................................................72
8.61 net tahi ipv6-Alias-Add(WAN) <ltip6_address>........................................................72
8.62 net tahi ipv6-Alias-Del(WAN) <ltip6_address> .........................................................72
8.63 net tahi reachable-time <lttime>....................................................................................73
8.64 net tahi ping6 <ltip> <ltsize>...........................................................................................73
8.65 net tahi mping6 <ltmip> ....................................................................................................73
8.66 net tahi pmtu-route-add <ltipAdd> ................................................................................73
8.67 net upnp configure..............................................................................................................73
Chapter 9. Configuration commands under branch SECURITY ............................................................74
9.1 security advanced_network attack_checks configure............................................ 74
9.2 security advanced_network igmp setup......................................................................74
9.3 security advanced_network igmp allowedsubnets add .........................................75
9.4 security advanced_network igmp allowedsubnets edit <ltrow_id>.................... 75
9.5 security advanced_network igmp allowedsubnets delete <ltrow_id> ...............75
9.6 security advanced_network ips setup..........................................................................75
9.7 security application_rules add........................................................................................76
9.8 security application_rules edit <ltrow_id>...................................................................76
9.9 security application_rules delete <ltrow_id>..............................................................77
9.10 security firewall custom_service add ...........................................................................77
9.11 security firewall custom_service edit <ltrow_id> ......................................................77
9.12 security firewall custom_service delete <ltrow_id> .................................................77
9.13 security firewall ipv4 configure .......................................................................................78
9.14 security firewall ipv4 default_outbound_policy <ltdefault_outbound_policy>.79
9.15 security firewall ipv4 edit <ltrow_id>.............................................................................79
9.16 security firewall ipv4 enable <ltrow_id>.......................................................................80
9.17 security firewall ipv4 disable <ltrow_id>......................................................................80
9.18 security firewall ipv4 delete <ltrow_id>........................................................................80
9.19 security firewall ipv4 move <ltrow_id> .........................................................................80
9.20 security firewall algs...........................................................................................................81
9.21 security firewall ipv6 configure .......................................................................................81
9.22 security firewall ipv6 edit <ltrow_id>.............................................................................82
9.23 security firewall ipv6 enable <ltrow_id>.......................................................................83
9.24 security firewall ipv6 disable <ltrow_id>......................................................................83
9.25 security firewall ipv6 delete <ltrow_id>........................................................................83
9.26 security firewall ipv6 move <ltrow_id> .........................................................................83
9.27 security firewall ipv6 default_outbound_policy <ltdefault_outbound_policy>.83
9.28 security ids configure.........................................................................................................84
9.29 security session_settings configure..............................................................................84

Unified Services Router CLI Reference Guide
5
9.30 security schedules add .....................................................................................................84
9.31 security schedules edit <ltrow_id>................................................................................85
9.32 security schedules delete <ltrow_id> ...........................................................................86
9.33 security mac_filter configure ...........................................................................................86
9.34 security mac_filter source add........................................................................................86
9.35 security mac_filter source edit <ltrow_id> ..................................................................86
9.36 security mac_filter source delete <ltrow_id> .............................................................87
9.37 security ip_or_mac_binding add....................................................................................87
9.38 security ip_or_mac_binding edit <ltrow_id> ..............................................................87
9.39 security ip_or_mac_binding delete <ltrow_id> .........................................................87
9.40 security firewall vpn_passthrough configure .............................................................88
9.41 security website_filter content_filtering configure....................................................88
9.42 security website_filter approved_urls add..................................................................88
9.43 security website_filter approved_urls edit <ltrow_id>.............................................88
9.44 security website_filter approved_urls delete <ltrow_id>........................................89
9.45 security website_filter blocked_keywords add..........................................................89
9.46 security website_filter blocked_keywords edit <ltrow_id> ....................................89
9.47 security website_filter blocked_keywords delete <ltrow_id> ...............................89
9.48 security website_filter blocked_keywords enable <ltrow_id> ..............................89
9.49 security website_filter blocked_keywords disable <ltrow_id> .............................90
Chapter 10. Configuration commands under branch SYSTEM.................................................................91
10.1 system logging ipv4 configure........................................................................................91
10.2 system logging facility configure <ltfacility>...............................................................92
10.3 system logging remote configure .................................................................................. 92
10.4 system logging ipv6 configure........................................................................................94
10.5 system remote_management https configure...........................................................94
10.6 system remote_management telnet configure .........................................................95
10.7 system snmp trap configure <ltagent_ip> ..................................................................95
10.8 system snmp trap delete <ltagent_ip>.........................................................................95
10.9 system snmp users configure <ltuser>........................................................................95
10.10 system snmp sys configure.............................................................................................96
10.11 system snmp access add.................................................................................................96
10.12 system snmp access edit <ltrowid>..............................................................................96
10.13 system snmp access delete <ltrowid>.........................................................................97
10.14 system switch_settings power_saving configure .....................................................97
10.15 system switch_settings jumbo_frame configure ......................................................97
10.16 system time configure .......................................................................................................97
10.17 system traffic_meter configure.......................................................................................98
10.18 system usb usb1 configure..............................................................................................99
10.19 system usb usb2 configure..............................................................................................99
10.20 system usb shareport_vlan configure <ltrow_id> ....................................................99
10.21 system groups configure ..................................................................................................99

Unified Services Router CLI Reference Guide
6
10.22 system group add .............................................................................................................100
10.23 system group edit <ltrow_id>........................................................................................100
10.24 system group delete <ltrow_id>...................................................................................100
10.25 system users add..............................................................................................................100
10.26 system users edit <ltrow_id> ........................................................................................101
10.27 system users delete <ltrow_id> ...................................................................................101
10.28 system users password <ltuser> .................................................................................101
10.29 system users idle_timeout <lttimeout>......................................................................101
10.30 system group groupaccesscontrol configure <ltgroup_id>.................................102
10.31 system group access_control_browser add............................................................102
10.32 system group access_control_browser delete <ltrow_id>..................................102
10.33 system group access_control_ip add ........................................................................102
10.34 system group access_control_ip delete <ltrow_id>..............................................103
Chapter 11. Configuration commands under branch DOT11...................................................................104
11.1 dot11 profile add <ltprofile_name>.............................................................................104
11.2 dot11 profile edit <ltprofile_name> .............................................................................104
11.3 dot11 radius configure.....................................................................................................105
11.4 dot11 profile delete <ltprofile_name> ........................................................................105
11.5 dot11 accesspoint configure <ltap_name>..............................................................105
11.6 dot11 accesspoint delete <ltap_name> ....................................................................106
11.7 dot11 accesspoint disable <ltap_name> ..................................................................106
11.8 dot11 accesspoint enable <ltap_name> ...................................................................106
11.9 dot11 radio configure.......................................................................................................106
11.10 dot11 radio advanced configure ..................................................................................107
11.11 dot11 accesspoint wps configure................................................................................107
11.12 dot11 accesspoint ACL configure <ltap_name>....................................................107
11.13 dot11 accesspoint acl delete_mac_address <ltrowid>........................................108
Chapter 12. Configuration commands under branch VPN........................................................................109
12.1 vpn l2tp server configure................................................................................................109
12.2 vpn pptp client configure ................................................................................................109
12.3 vpn pptp client_action <ltaction> .................................................................................110
12.4 vpn pptp server configure ..............................................................................................110
12.5 vpn sslvpn portal-layouts add.......................................................................................111
12.6 vpn sslvpn portal-layouts edit <ltrow_id>..................................................................111
12.7 vpn sslvpn portal-layouts delete <ltrow_id>............................................................. 112
12.8 vpn sslvpn portal-layouts set-default <ltrow_id>....................................................112
12.9 vpn sslvpn portforwarding appconfig add.................................................................112
12.10 vpn sslvpn portforwarding appconfig delete <ltrow_id> ......................................112
12.11 vpn sslvpn portforwarding hostconfig add................................................................112
12.12 vpn sslvpn portforwarding hostconfig delete <ltrow_id> .....................................113
12.13 vpn sslvpn resource add ................................................................................................ 113
12.14 vpn sslvpn resource configure add <ltresource_name> .....................................113

Unified Services Router CLI Reference Guide
7
12.15 vpn sslvpn resource configure delete <ltrow_id> ..................................................113
12.16 vpn sslvpn resource delete <ltrow_id>......................................................................114
12.17 vpn sslvpn policy add ......................................................................................................114
12.18 vpn sslvpn policy edit <ltrow_id>.................................................................................114
12.19 vpn sslvpn policy delete <ltrow_id>............................................................................115
12.20 vpn sslvpn client................................................................................................................115
12.21 vpn sslvpn route add........................................................................................................116
12.22 vpn sslvpn route delete <ltrow_id>.............................................................................116
12.23 vpn sslvpn users domains add.....................................................................................116
12.24 vpn sslvpn users domains edit <ltdomain_Name>................................................117
12.25 vpn sslvpn users domains delete <ltdomainname>..............................................118
12.26 vpn sslvpn users groups add........................................................................................118
12.27 vpn sslvpn users groups edit <ltrow_id>...................................................................118
12.28 vpn sslvpn users groups delete <ltrow_id>..............................................................118
12.29 vpn sslvpn users users add...........................................................................................118
12.30 vpn sslvpn users users edit <ltrow_id> .....................................................................119
12.31 vpn sslvpn users users login_policies <ltrow_id>..................................................119
12.32 vpn sslvpn users users browser_policies <ltrow_id> ...........................................120
12.33 vpn sslvpn users users ip_policies configure <ltrow_id>....................................120
12.34 vpn sslvpn users users ip_policies delete <ltrow_id> ..........................................120
12.35 vpn sslvpn users users delete <ltrow_id> ................................................................121
12.36 vpn ipsec policy configure <ltname> ..........................................................................121
12.37 vpn ipsec policy enable <ltname> ...............................................................................125
12.38 vpn ipsec policy disable <ltname>..............................................................................126
12.39 vpn ipsec policy delete <ltname>................................................................................126
12.40 vpn ipsec policy connect <ltname>.............................................................................126
12.41 vpn ipsec policy drop <ltname> ...................................................................................126
Chapter 13. Configuration commands under branch RADIUS ................................................................ 127
13.1 radius configure <ltradius_server> .............................................................................127
13.2 radius delete <ltradius_server>....................................................................................127

Unified Services Router CLI Reference Guide
8
Chapter 1. Introduction
This document describes the command line interface (CLI) for man aging D-Link's DSR-
1000N/1000/500N/500/250N/250/150/150N series of routers.
The CLI user requires advanced knowledge about the configuration of the system and should be
used only by those users who are familiar with CLI-based configuration.
Note that the following features in the DSR Unified Services Router cannot be managed
by the CLI: Firmware Upgrade
Configuration Backup / Restore
Certificate Generate / Upload
Power Savings mode configuration
System Dashboard / Resource Utilization
Please access the web browser based UI of the DSR router for managing these features.
1.1 Accessing the CLI
The CLI can be accessed by logging in with the same user credentials as used to
access the web browser based UI.
********************************************
Welcome to the DSR Command Line Interface
********************************************
D-Link DSR>
Note: D-Link DSR> is the CLI prompt.
RIP, WAN2, DMZ, Captive Portal related commands are not available on DSR -
250N/250/150/150N.
Wireless related commands are available on DSR-1000N, DSR-500N, DSR-150N
and DSR-250N only.

Unified Services Router CLI Reference Guide
9
Chapter 2. Basic commands available
on the CLI
2.1 CONTEXT SENSITIVE HELP
[?] - Display context sensitive help. This is either a list of possible command
completions with summaries, or the full syntax of the cu rrent command. A subsequent
repeat of this key, when a command has been resolved, will display a detailed
reference.
2.2 AUTO-COMPLETION
The following keys both perform auto-completion for the current command line. If the
command prefix is not unique a subsequ ent repeat of the key will display possible
completions.
[enter] - Auto-completes, syntax-checks then executes a command. If there is a
syntax error then offending part of the command line will be highlighted and
explained.
[space] - Auto-completes, or if the command is already resolved, inserts a
space.
2.3 MOVEMENT KEYS
[CTRL-A] - Move to the start of the line.
[CTRL-E] - Move to the end of the line.
[up] - Move to the previous command line held in history.
[down] - Move to the next command line held in history.
[left] - Move the insertion point left one character.
[right] - Move the insertion point right one character.
2.4 DELETION KEYS
[CTRL-C] - Delete the whole line.
[CTRL-D] - Delete the character to the right on the insertion point.
[CTRL-K] - Delete all the characters to the right of the insertion point.
[Backspace] - Delete the character to the left of the insertion point.

Unified Services Router CLI Reference Guide
10
2.5 ESCAPE SEQUENCES
!! - Substitute the last command line.
!N - Substitute the Nth command line (absolute as per 'history' command).
!-N - Substitute the command line entered N lines before (relative).

Unified Services Router CLI Reference Guide
11
Chapter 3. Command Hierarchy in CLI
3.1 CLI commands can be divided into 4
categories:
Global commands
Show commands
Utility commands
Configuration commands
3.2 The router configuration is divided into 5
branches:
Net: Network Settings
Security: Security Settings
System: Admin Settings
Dot11: Wireless Settings
Vpn: VPN Settings
Radius: RADIUS Settings

Unified Services Router CLI Reference Guide
12
Chapter 4. Global commands used in
CLI
.exit: Exit this session
.help: Display an overview of the CLI syntax
.top: Return to the default mode
.reboot: Reboot the system.
.history: Display the current session's command line history. Number of commands
in history list can be controlled by setting limit argument; by default it is
unbounded.

Unified Services Router CLI Reference Guide
13
Chapter 5. Show commands used in
CLI
The show commands for all the above mentioned branches are outlined in this section.
The command show net ? at the CLI prompt would give the description of all the show
commands in the branch net, which is as follows:
Sl No
Command Name
Purpose
1
show netipv6_tunnelstatus
Display ipv6tunnels status
2
show netbandwidth
.
3
show netbandwidthprofile
.
4
show netbandwidthprofilesetup
Show listof AvailableBandwidthProfile(s).
5
show netbandwidthtraffic_selector
.
6
show netbandwidth traffic_selector setup
Show listof AvailableTraffic Selector(s).
7
show netddns
.
8
show netddns setup
Show Dynamic DNS Configuration.
9
show netlandhcp
.
10
show netlandhcpreserved_ip
.
11
show netlandhcpreserved_ipsetup
Show listof DHCP ReservedAddresses.
12
show netlandhcpleased_clients
.
13
show netlandhcp leased_clients list
Show listof AvailableDHCP LeasedClients.
14
show netwandhcpc
Display dhcpclient Configuration.
15
show netdmz
.
16
show netdmz setup
Show DMZ Configuration.
17
show netdmz dhcp
.
18
show netdmz dhcp reserved_ip
.
19
show netdmz dhcp reserved_ipsetup
Show listof DMZ DHCP ReservedAddresses.
20
show netdmz dhcp leased_clients
.
21
show netdmz dhcp leased_clients list
Show listof AvailableDMZ DHCP LeasedClients.
22
show netethernet
Show Ethernetinterfaces
23
show netlan
.
24
show netlanipv4
.
25
show netlanipv4setup
Show LANConfiguration.
26
show netlanipv6
.
27
show netlanipv6setup
Show LANConfiguration.
28
show netstatistics <ltinterface>
Show InterfaceStatistics
29
show netintel_Amt
show IntelAmt server details
30
show netintel_Amtserver
show IntelAmt Server Configurations
31
show netintel_AmtReflector
show IntelAmt Reflector Configuration
32
show netintel_Amt server setup
Display net Intel_Amt server setup.
33
show netintel_Amt Reflector setup
Display net Intel_Amt Reflector setup.
34
show netIp_Alias
show IpAlias server details
35
show netIp_Alias server
show IpAlias configurationdetails
36
show netIp_Alias server setup
Display net Intel_Amt server setup.
37
show netmode
.
38
show netmodesetup
Display IP MODE configuration
39
show netipv6_tunnel
.
40
show netipv6_tunnelsetup
Display ipv6tunnels configuration
41
show netroutingmode
.
42
show netroutingmode setup
Routing Mode betw eenWANandLAN
43
show netwanwan1
.

Unified Services Router CLI Reference Guide
14
44
show netwanwan1ipv4
.
45
show netwanwan1ipv4status
Display ipv4wan1Information.
46
show netwanwan1ipv4setup
Display Wan1 Setup Information.
47
show netwanwan2
.
48
show netwanwan2ipv4
.
49
show netwanwan2ipv4status
Display ipv4wan2Information.
50
show netwanwan2ipv4setup
Display wan2SetupInformation.
51
show netwanwan3
Display the wan3configuration
52
show netwanwan3threeG
Show wan3configuration
53
show netwanwan3threeGsetup
Display wan3Information.
54
show netwanwan3threeGstatus
Display wan3status.
55
show netwan
.
56
show netwanmode
Display wanmodeInformation.
57
show netwanport_setup
Display wanportInformation.
58
show netwanconfigurable_port
Display configurableportInformation.
59
show netwanwan1ipv6
.
60
show netwanwan1ipv6status
Display ipv6wan1Information.
61
show netwanwan1ipv6setup
Display Wan1 Setup Information.
62
show netwanwan2ipv6
.
63
show netwanwan2ipv6status
Display ipv6wan2Information.
64
show netwanwan2ipv6setup
Display Wan2 Setup Information.
65
show netroutingospfv2
show OSPFv2Configuration
66
show netroutingospfv3
show OSPFv3Configuration
67
show netroutingospfv2setup
Display OSPFv2 Configuration
68
show netroutingospfv3setup
Display OSPFv3 Configuration
69
show netport
.
70
show netportmanagement
.
71
show netportmanagement setup
Display portmanagement configuration
72
show netwanpppoe
Display pppoe clientConfiguration.
73
show netroutingprotocol_binding
show protocol_bindingrules
74
show netroutingprotocol_bindingsetup
Display protocolBinding Rules
75
show netradvd
.
76
show netradvdsetup
Display RADVDconfiguration
77
show netroutingdynamic
Show dynamic routingsetup
78
show netroutingdynamic setup
Show dynamic routingSetup.
79
show netrouting
Displays routing setup
80
show netroutingstatic
.
81
show netroutingstatic ipv4
.
82
show netroutingstatic ipv4setup
Show allthe configuredIPV4 routes.
83
show netroutingstatic ipv6
.
84
show netroutingstatic ipv6setup
Show allthe configuredIPV6 routes.
85
show netupnp
Display UPnP Information
86
show netupnpportmap
Display UPnP portmap Information.
87
show netupnpsetup
Display UPnP portmap Information.
The command show security ? at the CLI prompt would give the description of all the show
commands in the branch security , which is as follows:
Sl No
Command Name
Purpose
1
show security advanced_network
show advancedfirewallattackchecks
2
show security advanced_networkattack_checks
Display Security Checks configuration
3
show security advanced_networkigmp
Display igmp configuration
4
show security advanced_networkips
Display ips configuration
5
show security application_rules
.
6
show security application_rules setup
Display application rules configuration

Unified Services Router CLI Reference Guide
15
7
show security application_rules status
Display application rules status
8
show security firewallcustom_service
.
9
show security firewallcustom_servicesetup
Display Custom Serviceconfiguration
10
show security firewall
Display FirewallRules
11
show security firewallipv4
Display FirewallRules
12
show security firewallipv4setup
Display FirewallRules
13
show security firewallalgs
Display ALGs protocals status
14
show security firewallipv6
Display IPV6 FirewallRules
15
show security firewallipv6setup
Display FirewallRules
16
show security ids
.
17
show security ids setup
Display IDS configuration
18
show security session_settings
Display SessionSettings configuration
19
show security schedules
.
20
show security schedules setup
Display Schedules configuration
21
show security mac_filter
.
22
show security mac_filter setup
Display SourceMac Filter configuration
23
show security ip_or_mac_binding
.
24
show security ip_or_mac_bindingsetup
Display IP/MAC Binding configuration
25
show security firewallvpn_passthrough
.
26
show security firewallvpn_passthroughsetup
Display VPN passthroughConfiguration
27
show security website_filter
.
28
show security website_filter content_filtering
Display contentfilteringconfiguration
29
show security website_filter approved_urls
Display trusteddomains configuration
30
show security website_filter blocked_keywords
Display blocked keyw ords configuration
The command show system ? at the CLI prompt would give the description of all the show
commands in the branch system , which is as follows:
Sl No
Command Name
Purpose
1
show systemlogging
.
2
show systemloggingremote
.
3
show systemloggingremote setup
Display remote logging configuration
4
show systemloggingfacility
.
5
show systemloggingfacility setup <ltfacility>
Display logging facility configuration
6
show systemloggingipv4
.
7
show systemloggingipv4 setup
Display logging configuration
8
show systemloggingipv6
.
9
show systemloggingipv6 setup
Display ipv6logs configuration
10
show systemlog
Display capturedlog messages of therouter activities
11
show systemlogall
Displays the all capturedlogmessages of the router
activities fromEvent Log. The logs displayedon this event
viewercanbedefinedinthe Log Configurationcommands
12
show systemlogpage
Displays Page Wise,capturedlog messages of therouter
activities fromEvent Log. The logs displayedon this event
viewercanbedefinedinthe Log Configurationcommands
13
show systemremote_management
.
14
show systemremote_management setup
Display remote management over https configuration
15
show systemsnmp<ltagentIP>
Display SNMP configuration
16
show systemswitch_setting
.
17
show systemswitch_settingpower_mode
Display power modeconfiguration
18
show systemswitch_settingjumbo_frame
Display jumbo frameconfiguration
19
show systemstatus
Display systemstatus
20
show systemtime
.
21
show systemtime setup
Display Timezone and NTP configuration
22
show systemtraffic_meter
.

Unified Services Router CLI Reference Guide
16
23
show systemtraffic_meter setup
Display traffic meter configuration
24
show systemusb
Display USB Configuration
25
show systemusers
Systemgroupdisplay mode
26
show systemgroup
Systemuser display mode
27
show systemgroupspecific<ltrow_id>
Display information for given group
28
show systemgroupall
Display all groups onsystem
29
show systemusers all
Display all users onsystem
30
show systemusers specific<ltrow_id>
Display information for given user
31
show systemgroupgroupaccesscontrol
<ltgroup_id>
Displays Group AccessControlconfigurationfor the
selectedgroup
32
show systemgroupaccess_control_browser
Displays Access Controlbrowserslist
33
show systemgroupaccess_control_ip
Displays Access Controlips list
34
show systemfirmwareVersion
Get's thefirmwareVersion.
The command show dot11 ? at the CLI prompt would give the description of all the show
commands in the branch dot11 , which is as follows:
Sl No
Com m and Nam e
Purpose
1
show dot11
Display 802.11 configuration
2
show dot11accesspoint<ltap_name>
Display AccessPoint configuration.This command displays
the list of configuredAccessPoints for thedevice
3
show dot11profile<ltprofile_name>
<ltdisplay_qos>
Display Profile configuration
4
show dot11statistics
Display access pointandradio statistics
5
show dot11acl<ltap_name>
Display access controllist informationfor thespecified
access point.
6
show dot11accesspointstatus<ltap_name>
Display wireless stats.
7
show dot11radius
Display radius Information.
8
show dot11wps
Display WPS Information.
9
show dot11wireless_statistics
Display w ireless_statisticsInformation.
10
show dot11radio
Display Radio configurationAvailableRadios This table
showsthelistof available radios that an APmay
The command show vpn ? at the CLI prompt would give the description of all the show
commands in the branch vpn , which is as follows:
Sl No
Com m and Nam e
Purpose
1
show vpnl2tp
show l2tpserver details
2
show vpnl2tpserver
show l2tpserver details
3
show vpnl2tpserver setup
Display l2tp server setup.
4
show vpnl2tpserver connections
Display l2tp server stats.
5
show vpnpptpclient
show pptpclientdetails
6
show vpnpptpclientsetup
Display pptp client setup.
7
show vpnpptpclient_status
show pptpclientstatus details
8
show vpnpptpclient_status setup
Display pptp client status setup.
9
show vpnpptp
show pptpserverdetails
10
show vpnpptpserver
show pptpserverdetails
11
show vpnpptpserversetup
Display pptp server setup.
12
show vpnpptpserverconnections
Display pptp server stats.
13
show vpnsslvpn
show sslvpnsettings
14
show vpnsslvpnclient
show sslvpnclientsettings
15
show vpnsslvpnroute
show routesettings
16
show vpnsslvpnpolicy
show sslvpnpolicy settings
17
show vpnsslvpnportal-layouts
show sslvpnportal-layoutssettings
18
show vpnsslvpnportforwarding
show sslvpnportforwardingsettings
19
show vpnsslvpnportforwardingappconfig
show sslvpnportforwardingappconfigsettings
20
show vpnsslvpnportforwardinghostconfig
show sslvpnportforwardinghostconfigsettings

Unified Services Router CLI Reference Guide
17
21
show vpnsslvpnresource
show sslvpnresourcesettings
22
show vpnsslvpnresource-object
<ltresource_name>
show sslvpnresourceobjectsettings
23
show vpnsslvpnusers
show sslvpnusersmode
24
show vpnsslvpnusersdomains
show sslvpndomains
25
show vpnsslvpnusersgroups
show sslvpngroups
26
show vpnsslvpnusersusers
show sslvpnusers
27
show vpnsslvpnusersbrowser_policies <ltrow_id>
show sslvpnuserspolicies by browser
28
show vpnsslvpnuserslogin_policies <ltrow_id>
show sslvpnusersloginpolicies
29
show vpnsslvpnusersip_policies <ltrow_id>
show sslvpnusersippolicy
30
show vpnipsec
show vpnpolicy
31
show vpnipsec policy
show vpnpolicy
32
show vpnipsec policy setup
show vpnpolicy
33
show vpnipsec policy status
show vpnstatus
34
show vpnipsec dhcp
show vpnipsec dhcpsetup
35
show vpnipsec dhcpsetup
show vpnipsec dhcpsetup
The command show radius ? at the CLI prompt would give the description of all the show
commands in the branch radius , which is as follows:
Sl No
Com m and Nam e
Purpose
1
show radius <ltserver>
Display radius configuration.

Unified Services Router CLI Reference Guide
18
Chapter 6. Utility commands used in
CLI
The command util ? at the CLI prompt would give the description of all the utility commands in
the branch util, which is as follows:
Sl No
Command Name
Purpose
1
util ping
Ping or Tracean IP Address.
2
util restore_factory_defaults
Revertto factory defaultsettings.
3
util reboot
Reboot the system
6.1 util system_check ping <ltip_address>
S.No
CommandName
Description
Type and Description
1
<ltip_address>
Ping an Internet Address.
String
6.2 util system_check dns_lookup <ltdns>
S.No
Command
Name
Description
Type and
Description
1
<ltdns>
To retrievethe IP address of aWeb, FTP, Mail or any other Server onthe
Internet
String
6.3 util system_check traceroute
<ltip_address>
S.No
Command
Name
Description
Type and
Description
1
<ltip_address>
display all the routers presentbetweenthedestinationIP address andthis
router
String
6.4 util system_check capturePackets start
<ltinterface>
S.No
CommandName
Description
Type and Description
1
<ltinterface>
Start thepacket capture
WANinterfacetype
6.5 util system_check capturePackets
download <ltfileName> <ltipAddr>
S.No
CommandName
Description
Type and Description
1
<ltfileName>
<ltipAddr>
Downloadthepacket capturetothe
hostmachine
String
IP address AAA.BBB.CCC.DDD whereeachpartis in
the range0-255