D-Link DSL-2740M User manual

WIRELESS N300
ADSL2+ MODEM ROUTER
D SL- 274 0M
QUICK
INSTALLATION
GUIDE

DS L- 2740M
2
ENGLISH
CONTENTS OF
PACKAGING
CONTENTS
POWER ADAPTER
ADAPTER
ETHERNET CABLE (CAT5 UTP)
CONNECT THE ROUTER TO YOUR PC DURING SET-UP
If any of these items are missing from your packaging contact
your reseller
WIRELESS N300 ADSL2+ MODEM ROUTER
DSL-2740M
RJ-11 PHONE CABLE
ADSL SPLITTER

DS L- 2740M 3
ENGLISH
PRODUCT
SETUP
BEFORE YOU START
Internet Provider Account Details - If you are using an Australian or New Zeleand ADSL connection,
you will need your user name and password. If you do not have this information, contact your Internet
Service Provider.
Do not proceed until you have this information.
SETUP YOUR MODEM ROUTER
1. Open a web browser (e.g., Internet Explorer, Chrome, Firefox, or Safari) and enter ‘192.168.1.1’
into the address bar (http://192.168.1.1).
2. When prompted, enter 'admin' into both the username and password elds and click 'Login'.
3. Click on 'Setup Wizard' to start conguring your Router.
CONNECT YOUR MODEM ROUTER
1. Connect the supplied Splitter/Filter to your telephone outlet.
2. Take the supplied RJ-11 phone cable and plug it into the DSL port of the Splitter/Filter. Plug the
other end into the DSL port of the Router.
3. Plug the supplied Ethernet cable into one of the Ethernet ports on the back of your Router and
connect the other end into the Ethernet port on your computer.
4. Connect the supplied power adapter to the back of your Router and power the device on.

DS L- 2740M
4
ENGLISH
4. You have the option to change your routers administration password. You can also skip this step.
5. From the drop down lists, select your country and ISP. The required connection details will autoll for
an ADSL connection. If your ISP isn't listed, select 'Others' and enter the required details manually.
6. Enter your ADSL Username and Password, as supplied by your ISP.
7. Click 'Finish' to complete the Setup Wizard. Once settings are saved, you should be online and able to
access the Internet after a short period.
8. Other advanced settings can be congured by clicking on other tabs within the user interface. For
more information, please consult the user guide.

TROUBLESHOOTING
SET-UP AND CONFIGURATION PROBLEMS
1. HOW DO I CONFIGURE MY DSL-2740M ROUTER WITHOUT THE CD, OR CHECK MY
WIRELESS NETWORK NAME (SSID) AND WIRELESS ENCRYPTION KEY?
- Connect your PC to the router using an Ethernet cable.
- Open a web browser and enter the address http://192.168.1.1
- The default username is ‘admin’. The default password is 'admin'.
- If you have changed the password and can not remember it, you will need to reset the router to
set the password back to 'admin'.
2. HOW DO I RESET MY DSL-2740M ROUTER TO FACTORY DEFAULT SETTINGS?
- Ensure the router is powered on.
- Press and hold the reset button on the rear of the device for 10 seconds.
Note: Resetting the router to factory default will erase the current conguration settings.
To re-congure your settings, log into the router as outlined in question 1, then follow the steps
in the 'SETUP YOUR MODEM ROUTER SECTION' of this QIG
3. HOW DO I ADD A NEW WIRELESS CLIENT OR PC IF I HAVE FORGOTTEN MY
WIRELESS NETWORK NAME (SSID) OR WIRELESS ENCRYPTION KEY?
- Every PC that needs to connect to the router wirelessly, you will need to ensure you use the
correct Wireless Network Name (SSID) and encryption key.
- Use the web based user interface (as described in question 1 above) to check or choose your
wireless settings.
- Make sure you write down these settings so that you can enter them into each wirelessly
connected PC. You will nd a dedicated area on the back of this document to record this
important information for future use.
4. WHY CAN I NOT GET AN INTERNET CONNECTION?
- Please contact your ISP to make sure the service has been enabled/connected by your ISP and
that your ISP username and password is correct.

NOTES

NOTES

Ver. 1.00(AU) 27/07/2016
WIRELESS NETWORK REMINDER
Wireless Network Name (SSID)
Wireless Network Password