D-Link DSL-2750U User manual

Quick Installation Guide
DSL-2750U
Wireless ADSL2+ Router with
3G/LTE/Ethernet WAN Su ort
and USB Port

DSL-2750U Quick Installation Guide
BEFORE YOU BEGI
Delivery Package
•Router DSL-2750U
•Power adapter DC 12V/1A
•RJ-11 telephone ca le
•Ethernet ca le (CAT 5E)
•Splitter
•“Quick Installation Guide” ( rochure).
If any of the items are missing, please contact your reseller.
The “User Manual” and “Quick Installation Guide” documents are availa le
on D-Link we site (see www.dlink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
Default Settings
IP address of wireless router 192.168.1.1
Username (login) admin
Password admin
ame of wireless network (SSID) DSL-2750U
etwork key (PSK)
see WPS PIN on the
arcode la el on the
ottom panel of the
device
2

DSL-2750U Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a we rowser.
•A we rowser to access the we - ased interface of the router:
◦Apple Safari 5 and later
◦Google Chrome 5 and later
◦Microsoft Internet Explorer 8 and later
◦Mozilla Firefox 5 and later
◦Opera 10 and later.
•A NIC (Ethernet or Wi-Fi adapter) to connect to the router.
•An 802.11 , g, or n Wi-Fi adapter to create a wireless network.
•A USB modem to connect to the Internet1.
!
Your USB modem should e equipped with an active identification
card (SIM or R-UIM) of your operator.
Some operators require su scri ers to activate their USB modems prior
to using them. Please, refer to connection guidelines provided y your
operator when concluding the agreement or placed on its we site.
For LTE and CDMA USB modems, it is required to disa le the PIN
code check on the identification card prior to connecting the USB
modem to the router.
1 Contact your operator to get information on the service coverage and fees.
3

DSL-2750U Quick Installation Guide
Supported USB Modems
GSM modems
•Alcatel X500
•D-Link DWM-152C1
•D-Link DWM-156A6
•D-Link DWM-156A7
•D-Link DWM-156C1
•D-Link DWM-157B1
•D-Link DWM-157B1 (Velcom)
•D-Link DWM-158D1
•Huawei E150
•Huawei E1550
•Huawei E156G
•Huawei E160G
•Huawei E169G
•Huawei E171
•Huawei E173 (Megafon)
•Huawei E220
•Huawei E352 (Megafon)
•Huawei E367 (3G mode)
•Huawei E392 (3G mode)
•ZTE MF112
•ZTE MF192
•ZTE MF626
•ZTE MF627
•ZTE MF652
•ZTE MF667
•ZTE MF668
•ZTE MF752
4

DSL-2750U Quick Installation Guide
CDMA modems2
•Airplus MCD-650
•Airplus MCD-800
•AnyDATA ADU-300A
•AnyDATA ADU-500A
•AnyDATA ADU-510A
•Huawei EC306
•ZTE AC5710
•ZTE AC5730
L E modems
•Huawei E3131
•Huawei E3272
•Huawei E367
•Huawei E392
•Megafon M100-1
•Megafon M100-3
•Megafon M100-4
•Megafon M150-1
•MTS 824F
•Yota LU-150
•Yota WLTUBA-107
•ZTE MF823
•ZTE MF827
!The manufacturer does not guarantee proper operation of the router
with every modification of the firmware of USB modems.
2 Performance of CDMA USB modems is not tested for the current firmware version.
5

DSL-2750U Quick Installation Guide
CO ECTI G TO PC
PC wit Et ernet Adapter
1. Make sure that your PC is powered off.
2. Connect an Ethernet ca le etween any of four Ethernet ports located on
the ack panel of the router and the Ethernet port of your PC.
3. To connect via USB modem: connect your USB modem to the USB port3
located on the left side panel of the router.
!If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
4. To connect the router to a DSL line: connect a phone ca le etween the
DSL port of the router and the ADSL OU port of the splitter. Connect
your phone to the PHONE port of the splitter. Then connect another
phone ca le etween a phone jack and the ADSL IN port of the splitter.
5. To connect the router to an Ethernet line: in the we - ased interface of
the router, select the router's LAN port that will e used as the WAN port
and create an Ethernet WAN connection. Then connect the Ethernet ca le
etween the selected Ethernet port located on the ack panel of the router
and the Ethernet line.
6. Connect the power cord to the power connector port on the ack panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
7. Turn on the router y pressing the ON/OFF utton on its ack panel.
8. Turn on your PC and wait until your operating system is completely
loaded.
Now you should configure your PC to o tain an IP address automatically (as
DHCP client).
3 It is recommended to use a USB extension ca le to connect a USB modem to the
router.
6

DSL-2750U Quick Installation Guide
Obtaining IP Address Automatically
in OS Windows XP
1. Click the Start utton and proceed to the Control Panel > etwork
and Internet Connections > etwork Connections window.
2. In the etwork Connections window, right-click the relevant Local
Area Connection icon and select the Properties line in the menu
displayed.
3. In the Local Area Connection Properties window, on the General
ta , select the Internet Protocol (TCP/IP) line. Click the Properties
utton.
7

DSL-2750U Quick Installation Guide
4. Select the Obtain an IP address automatically and Obtain D S
server address automatically radio uttons. Click the OK utton.
5. Click the ОК utton in the connection properties window.
Now your computer is configured to o tain an IP address automatically.
8

DSL-2750U Quick Installation Guide
Obtaining IP Address Automatically
in OS Windows 7
1. Click the Start utton and proceed to the Control Panel window.
2. Select the etwork and Sharing Center section. (If the Control Panel
has the category view (the Category value is selected from the View by
drop-down list in the top right corner of the window), choose the View
network status and tasks line under the etwork and Internet
section.)
3. In the menu located on the left part of the window, select the Change
adapter settings line.
4. In the opened window, right-click the relevant Local Area Connection
icon and select the Properties line in the menu displayed.
5. In the Local Area Connection Properties window, on the
etworking ta , select the Internet Protocol Version 4 (TCP/IPv4)
line. Click the Properties utton.
9

DSL-2750U Quick Installation Guide
6. Select the Obtain an IP address automatically and Obtain D S
server address automatically radio uttons. Click the OK utton.
7. Click the OK utton in the connection properties window.
Now your computer is configured to o tain an IP address automatically.
10

DSL-2750U Quick Installation Guide
PC wit Wi-Fi Adapter
1. To connect via USB modem: connect your USB modem to the USB port4
located on the left side panel of the router.
!If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
2. To connect the router to a DSL line: connect a phone ca le etween the
DSL port of the router and the ADSL OU port of the splitter. Connect
your phone to the PHONE port of the splitter. Then connect another
phone ca le etween a phone jack and the ADSL IN port of the splitter.
3. To connect the router to an Ethernet line: in the we - ased interface of
the router, select the router's LAN port that will e used as the WAN port
and create an Ethernet WAN connection. Then connect the Ethernet ca le
etween the selected Ethernet port located on the ack panel of the router
and the Ethernet line.
4. Connect the power cord to the power connector port on the ack panel of
the router, then plug the power adapter into an electrical outlet or power
strip.
5. Turn on the router y pressing the ON/OFF utton on its ack panel.
6. Turn on your PC and wait until your operating system is completely
loaded.
7. Turn on your Wi-Fi adapter. As a rule, modern note ooks with uilt-in
wireless NICs are equipped with a utton or switch that turns on/off the
wireless adapter (refer to your PC documents). If your PC is equipped
with a plugga le wireless NIC, install the software provided with your
Wi-Fi adapter.
Now you should configure your Wi-Fi adapter.
4 It is recommended to use a USB extension ca le to connect a USB modem to the
router.
11

DSL-2750U Quick Installation Guide
Configuring Wi-Fi Adapter in OS Windows XP
1. Click the Start utton and proceed to the Control Panel > etwork
and Internet Connections > etwork Connections window.
2. Select the icon of the wireless network connection and make sure that
your Wi-Fi adapter is on.
3. Search for availa le wireless networks.
4. In the opened Wireless etwork Connection window, select the
wireless network DSL-2750U and click the Connect utton.
5. In the opened window, enter the network key (see WPS PIN on the
arcode la el on the ottom panel of the device) in the etwork key and
Confirm network key fields and click the Connect utton.
After that the Wireless etwork Connection Status window appears.
!
If you perform initial configuration of the router via Wi-Fi connection,
note that immediately after changing the wireless default settings of the
router you will need to reconfigure the wireless connection using the
newly specified settings.
12

DSL-2750U Quick Installation Guide
Configuring Wi-Fi Adapter in OS Windows 7
1. Click the Start utton and proceed to the Control Panel window.
2. Select the etwork and Sharing Center section. (If the Control Panel
has the category view (the Category value is selected from the View by
drop-down list in the top right corner of the window), choose the View
network status and tasks line under the etwork and Internet
section.)
3. In the menu located on the left part of the window, select the Change
adapter settings line.
4. In the opened window, select the icon of the wireless network connection
and make sure that your Wi-Fi adapter is on.
5. To open the list of availa le wireless networks, select the icon of the
wireless network connection and click the Connect To utton or left-
click the network icon in the notification area located on the right side of
the task ar.
13

DSL-2750U Quick Installation Guide
6. In the opened window, in the list of availa le wireless networks, select the
wireless network DSL-2750U and click the Connect utton.
7. In the opened window, enter the network key (see WPS PIN on the
arcode la el on the ottom panel of the device) in the Security key
field and click the OK utton.
8. Wait for a out 20-30 seconds. After the connection is esta lished, the
network icon will e displayed as the signal level scale.
!
If you perform initial configuration of the router via Wi-Fi connection,
note that immediately after changing the wireless default settings of the
router you will need to reconfigure the wireless connection using the
newly specified settings.
14

DSL-2750U Quick Installation Guide
CO FIGURI G ROUTER
Connecting to Web-based Interface
Start a we rowser. In the address ar of the we rowser, enter the IP
address of the router ( y default, the following IP address is specified:
192.168.1.1). Press the Enter key.
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to remote server ”) occurs upon connecting to
the we - ased interface of the router, make sure that you have properly
connected the router to your computer.
After the first access to the we - ased interface you need to change the default
administrator password. Enter the new password in the Password and
Confirmation fields. You may set any password except admin. Use digits,
Latin letters (uppercase and/or lowercase), and characters availa le on the
key oard. Then click the Apply utton.
!
Remem er or write down the new password for the administrator
account. In case of losing the new password, you can access the settings
of the router only after restoring the factory default settings via the
hardware RESE utton. This procedure wipes out all settings that you
have configured for your router.
15

DSL-2750U Quick Installation Guide
When the we - ased interface is accessed the next time and after, the login
page opens. Enter the username (admin) in the Login field and the password
you specified in the Password field, then click the Enter utton.
16

DSL-2750U Quick Installation Guide
After successful registration the Home / Information page opens. The page
displays general information on the router and its software.
17

DSL-2750U Quick Installation Guide
The we - ased interface of the router is multilingual. If you need to select
another language for the we - ased interface, place the mouse pointer over the
English caption in the top part of the page and select a language from the
menu displayed.
To configure the router use the menu in the left part of the page. Go to the
relevant section and select the needed page or run the needed Wizard in the
Home section.
Also you can find a specific page via search. To do this, enter the name of the
page, wholly or partly, in the search ar in the top part of the we - ased
interface page, and then select a needed link in the search results.
18

DSL-2750U Quick Installation Guide
Configuring Connection to t e Internet
!
You should configure your WAN connection in accordance with data
provided y your Internet service provider (ISP). Make sure that you
have o tained all necessary information prior to configuring your WAN
connection. Otherwise contact your ISP.
LTE WAN Connection
If the PIN code check is ena led for the SIM card inserted into your LTE USB
modem, it is required to disa le the PIN code check on the identification card
prior to connecting the USB modem to the router.
An active LTE WAN connection will e automatically created on the et /
WA page when connecting a USB modem to the router. If the connection has
not een created automatically, create a new connection manually.
!For the USB modem Megafon M100-1, please re oot the router after
creating the WAN connection.
1. Go to the et / WA page and click the Add utton.
2. In the General settings section, in the Provider drop-down list, leave
the Manually value.
3. From the Connection Type drop-down list, select the LTE value.
4. Make sure that the USB value is selected from the Interface drop-down
list.
5. Specify a name for your connection (any name for easier identification) in
the ame field.
19

DSL-2750U Quick Installation Guide
6. If your operator requires to specify the access point name, in the USB
modem section, fill in the AP field.
7. If your operator has provided the address of the DNS server, in the IP
section, deselect the Obtain D S server addresses automatically
check ox and fill in the Primary D S server field.
8. Click the Apply utton.
9. On the et / WA page, select the choice of the Default gateway radio
utton corresponding to the new LTE WAN connection.
20