D-Link DSL-524B User manual

Quick Installation Guide
DSL-524B Generation II
ADSL2+ Router

2
Before You Begin
Check Your Package Contents
Make sure you have all the necessary information and equipment on hand
before beginning the installation.
DSL-524B ADSL Modem
CD-ROM (containing Manual)
Ethernet (CAT5 UTP) Cable
Telephone Cable
Power Adapter
If any of the above items are missing, please contact your reseller

3
Connecting the Modem to Your Computer
A. First, connect the power adapter to the receptor at the back panel of the
DSL-524B and then plug the other end of the power adapter to a wall outlet or
power strip. The Power LED will turn ON to indicate proper operation.
B. Insert one end of the cable into the Ethernet port on the back panel of the
DSL-524B and the other end of the cable to an Ethernet Adapter or available
Ethernet port on your computer.
ADSL Port
Use the ADSL cable to connect to the
your telephone line (RJ-11 port)
Ethernet Port
Use the Ethernet port to connect
the Router to a computer or an
Ethernet LAN
Power Insert
Use the adapter shipped with
the Router to connect to power
source
Power Button
Push in to power-on the Router.
Push again to power-off the Router
Reset Button
To manually reset, depress button with
the power on for at least seven seconds
1

4
Conguring the Modem
To use your Web browser to access the web pages used to setup the Modem, your computer must be
congured to “Obtain an IP address automatically”, that is, you must change the IP network settings of your
computer so that it is a DHCP Client. If you are using Windows XP and do not know how to change your
network settings, skip ahead to Appendix A and read the instructions provided. You may also read the User
Manual for instructions on changing IP settings for computers running Windows operating systems.
2
Open your Web browser and type
“http://192.168.1.1” into the URL address box.
Then press the Enter or Return key.
The Login page appears.
Type “admin” for the
Login Name and “admin”
in the Password eld. Click OK
Power Insert

5
Conguring the Modem (continued)
Click “WAN” on the left page, enter into “WAN Area Network (WAN) Setup” conguration page.
Click on the next connection which you want modify. Press “Add” button, enter the congure guide,
as following picture showed.
2

6
The value for VPI/VCI is assigned by your ISP. After inputting the PVC value, press “Next” to “Connection
Type”, as following picture showed.
Select “PPP over Ethernet (PPPoE)”, press “Next” entering the conguring interface, as following
picture showed.

7
Congure your PPP Username and Password from ISP. Then press “Next” to “Network Address
Translation Settings”, as following picture showed.
Press “Next” to enter into “WAN Setup - Summary”, click “Save” to save conguration, if you need
to modify the parameter, click “Back”, as following picture showed.

8
Conguring the Modem (continued)
To save the new settings, please access Management menu , click the Save/reboot button in the Save/
reboot menu. After a few seconds, the changes will be saved. The Modem will automatically establish the
Internet connection after a few more seconds.
Wait a few seconds for the Internet connection to be established and proceed to access the Internet via your web browser.
2
Click Save/reboot button to
save the new settings.

9
For additional settings or information, refer to the Advanced, Tools, or Status tabs on the web-
management interface; or to the manual located on the CD-ROM.
Use the following steps to congure a computer running Windows XP to be a DHCP client.
1. From the Start menu on your desktop, go to Settings, then click on Network Connections.
2. In the Network Connections window, right-click on LAN (Local Area Connection), then click Properties.
Conguring IP Settings in Windows XP
Appendix

10
3. In the General tab of the Local Area Connection Properties menu, highlight Internet Protocol (TCP/IP)
under “This connection uses the following items:” by clicking on it once. Click on the Properties button.
Right-click on the Local Area Connection
icon and Select the Properties option
from the pull-down menu.
Click Properties