D-Link WMP-A12 User manual

i
WMP-A12
5GHz Wireless LAN mini PCI Card
User’s Manual
First Edition (May, 2002)
6WMPA12...01

Wichtige Sicherheitshinweise
1. Bitte lesen Sie sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den spätern Gebr uch  uf.
3. Vor jedem Reinigen ist d s Gerät vom Stromnetz zu trennen. Vervenden Sie keine Flüssig- oder
Aerosolreiniger. Am besten dient ein  ngefeuchtetes Tuch zur Reinigung.
4. Um eine Beschädigung des Gerätes zu vermeiden sollten Sie nur Zubehörteile verwenden, die vom Hersteller
zugel ssen sind.
5. D s Gerät is vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist  uf sichern St nd zu  chten. Ein Kippen oder F llen könnte Verletzungen
hervorrufen. Verwenden Sie nur sichere St ndorte und be chten Sie die Aufstellhinweise des Herstellers.
7. Die Belüftungsöffnungen dienen zur Luftzirkul tion die d s Gerät vor Überhitzung schützt. Sorgen Sie d für,
d ß diese Öffnungen nicht  bgedeckt werden.
8. Be chten Sie beim Anschluß  n d s Stromnetz die Anschlußwerte.
9. Die Netz nschlußsteckdose muß  us Gründen der elektrischen Sicherheit einen Schutzleiterkont kt h ben.
10. Verlegen Sie die Netz nschlußleitung so, d ß niem nd d rüber f llen k nn. Es sollete  uch nichts  uf der
Leitung  bgestellt werden.
11. Alle Hinweise und W rnungen die sich  m Geräten befinden sind zu be chten.
12. Wird d s Gerät über einen längeren Zeitr um nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit
wird im Flle einer Übersp nnung eine Beschädigung vermieden.
13. Durch die Lüftungsöffnungen dürfen niem ls Gegenstände oder Flüssigkeiten in d s Gerät gel ngen. Dies
könnte einen Br nd bzw. Elektrischen Schl g  uslösen.
14. Öffnen Sie niem ls d s Gerät. D s Gerät d rf  us Gründen der elektrischen Sicherheit nur von  uthorisiertem
Serviceperson l geöffnet werden.
15. Wenn folgende Situ tionen  uftreten ist d s Gerät vom Stromnetz zu trennen und von einer qu lifizierten
Servicestelle zu überprüfen:
 – Netzk bel oder Netzstecker sint beschädigt.
b – Flüssigkeit ist in d s Gerät eingedrungen.
c – D s Gerät w r Feuchtigkeit  usgesetzt.
d – Wenn d s Gerät nicht der Bedienungs nleitung ensprechend funktioniert oder Sie mit Hilfe dieser Anleitung
keine Verbesserung erzielen.
e – D s Gerät ist gef llen und/oder d s Gehäuse ist beschädigt.
f – Wenn d s Gerät deutliche Anzeichen eines Defektes  ufweist.
16. Bei Rep r turen dürfen nur  rgin lers tzteile bzw. den  rgin lteilen entsprechende Teile verwendet werden.
Der Eins tz von ungeeigneten Ers tzteilen k nn eine weitere Beschädigung hervorrufen.
17. Wenden Sie sich mit  llen Fr gen die Service und Rep rtur betreffen  n Ihren Servicep rtner. Somit stellen
Sie die Betriebssicherheit des Gerätes sicher.

iii
18. Zum Netz nschluß dieses Gerätes ist eine geprüfte Leitung zu verwenden, Für einen Nennstrom bis 6A und
einem Gerätegewicht großer 3kg ist eine Leitung nicht leichter  ls H05VV-F, 3G, 0.75mm2 einzusetzen
Limited Warranty
Hardware:
D-LINK WARRANTS EACH  F ITS HARDWARE PR DUCTS T BE FREE FR M DEFECTS IN W RKMANSHIP AND
MATERIALS UNDER N RMAL USE AND SERVICE F R A PERI D C MMENCING  N THE DATE  F PURCHASE FR M
D-LINK  R ITS AUTH RIZED RESELLER AND EXTENDING F R THE LENGTH  F TIME STIPULATED BY THE
AUTH RIZED RESELLER  R D-LINK BRANCH  FFICE NEAREST T THE PLACE  F PURCHASE.
THIS WARRANTY APPLIES  N THE C NDITI N THAT THE PR DUCT REGISTRATI N CARD IS FILLED  UT AND
RETURNED T A D-LINK  FFICE WITHIN NINETY (90) DAYS  F PURCHASE. A LIST  F D-LINK  FFICES IS
PR VIDED AT THE BACK  F THIS MANUAL, T GETHER WITH A C PY  F THE REGISTRATI N CARD.
IF THE PR DUCT PR VES DEFECTIVE WITHIN THE APPLICABLE WARRANTY PERI D, D-LINK WILL PR VIDE
REPAIR  R REPLACEMENT  F THE PR DUCT. D-LINK SHALL HAVE THE S LE DISCRETI N WHETHER T REPAIR
 R REPLACE, AND REPLACEMENT PR DUCT MAY BE NEW  R REC NDITI NED. REPLACEMENT PR DUCT
SHALL BE  F EQUIVALENT  R BETTER SPECIFICATI NS, RELATIVE T THE DEFECTIVE PR DUCT, BUT NEED N T
BE IDENTICAL. ANY PR DUCT  R PART REPAIRED BY D-LINK PURSUANT T THIS WARRANTY SHALL HAVE A
WARRANTY PERI D  F N T LESS THAN 90 DAYS, FR M DATE  F SUCH REPAIR, IRRESPECTIVE  F ANY EARLIER
EXPIRATI N  F  RIGINAL WARRANTY PERI D. WHEN D-LINK PR VIDES REPLACEMENT, THEN THE DEFECTIVE
PR DUCT BEC MES THE PR PERTY  F D-LINK .
WARRANTY SERVICE MAY BE  BTAINED BY C NTACTING A D-LINK  FFICE WITHIN THE APPLICABLE
WARRANTY PERI D, AND REQUESTING A RETURN MATERIAL AUTH RIZATI N (RMA) NUMBER. IF A
REGISTRATI N CARD F R THE PR DUCT IN QUESTI N HAS N T BEEN RETURNED T D-LINK , THEN A PR  F  F
PURCHASE (SUCH AS A C PY  F THE DATED PURCHASE INV ICE) MUST BE PR VIDED. IF PURCHASER’S
CIRCUMSTANCES REQUIRE SPECIAL HANDLING  F WARRANTY C RRECTI N, THEN AT THE TIME  F
REQUESTING RMA NUMBER, PURCHASER MAY ALS PR P SE SPECIAL PR CEDURE AS MAY BE SUITABLE T THE
CASE.
AFTER AN RMA NUMBER IS ISSUED, THE DEFECTIVE PR DUCT MUST BE PACKAGED SECURELY IN THE  RIGINAL
 R  THER SUITABLE SHIPPING PACKAGE T ENSURE THAT IT WILL N T BE DAMAGED IN TRANSIT, AND THE
RMA NUMBER MUST BE PR MINENTLY MARKED  N THE  UTSIDE  F THE PACKAGE. THE PACKAGE MUST BE
MAILED  R  THERWISE SHIPPED T D-LINK WITH ALL C STS  F MAILING/SHIPPING/INSURANCE PREPAID. D-
LINK SHALL NEVER BE RESP NSIBLE F R ANY S FTWARE, FIRMWARE, INF RMATI N,  R MEM RY DATA  F
PURCHASER C NTAINED IN, ST RED  N,  R INTEGRATED WITH ANY PR DUCT RETURNED T D-LINK
PURSUANT T THIS WARRANTY.

ANY PACKAGE RETURNED T D-LINK WITH UT AN RMA NUMBER WILL BE REJECTED AND SHIPPED BACK T
PURCHASER AT PURCHASER’S EXPENSE, AND D-LINK RESERVES THE RIGHT IN SUCH A CASE T LEVY A
REAS NABLE HANDLING CHARGE IN ADDITI N MAILING  R SHIPPING C STS.
Software:
WARRANTY SERVICE F R S FTWARE PR DUCTS MAY BE  BTAINED BY C NTACTING A D-LINK  FFICE WITHIN
THE APPLICABLE WARRANTY PERI D. A LIST  F D-LINK  FFICES IS PR VIDED AT THE BACK  F THIS MANUAL,
T GETHER WITH A C PY  F THE REGISTRATI N CARD. IF A REGISTRATI N CARD F R THE PR DUCT IN
QUESTI N HAS N T BEEN RETURNED T A D-LINK  FFICE, THEN A PR  F  F PURCHASE (SUCH AS A C PY  F
THE DATED PURCHASE INV ICE) MUST BE PR VIDED WHEN REQUESTING WARRANTY SERVICE. THE TERM
“PURCHASE” IN THIS S FTWARE WARRANTY REFERS T THE PURCHASE TRANSACTI N AND RESULTING
LICENSE T USE SUCH S FTWARE.
D-LINK WARRANTS THAT ITS S FTWARE PR DUCTS WILL PERF RM IN SUBSTANTIAL C NF RMANCE WITH THE
APPLICABLE PR DUCT D CUMENTATI N PR VIDED BY D-LINK WITH SUCH S FTWARE PR DUCT, F R A
PERI D  F NINETY (90) DAYS FR M THE DATE  F PURCHASE FR M D-LINK  R ITS AUTH RIZED RESELLER. D-
LINK WARRANTS THE MAGNETIC MEDIA,  N WHICH D-LINK PR VIDES ITS S FTWARE PR DUCT, AGAINST
FAILURE DURING THE SAME WARRANTY PERI D. THIS WARRANTY APPLIES T PURCHASED S FTWARE, AND T
REPLACEMENT S FTWARE PR VIDED BY D-LINK PURSUANT T THIS WARRANTY, BUT SHALL N T APPLY T
ANY UPDATE  R REPLACEMENT WHICH MAY BE PR VIDED F R D WNL AD VIA THE INTERNET,  R T ANY
UPDATE WHICH MAY  THERWISE BE PR VIDED FREE  F CHARGE.
D-LINK ’S S LE  BLIGATI N UNDER THIS S FTWARE WARRANTY SHALL BE T REPLACE ANY DEFECTIVE
S FTWARE PR DUCT WITH PR DUCT WHICH SUBSTANTIALLY C NF RMS T D-LINK ’S APPLICABLE PR DUCT
D CUMENTATI N. PURCHASER ASSUMES RESP NSIBILITY F R THE SELECTI N  F APPR PRIATE APPLICATI N
AND SYSTEM/PLATF RM S FTWARE AND ASS CIATED REFERENCE MATERIALS. D-LINK MAKES N WARRANTY
THAT ITS S FTWARE PR DUCTS WILL W RK IN C MBINATI N WITH ANY HARDWARE,  R ANY APPLICATI N
 R SYSTEM/PLATF RM S FTWARE PR DUCT PR VIDED BY ANY THIRD PARTY, EXCEPTING  NLY SUCH
PR DUCTS AS ARE EXPRESSLY REPRESENTED, IN D-LINK ’S APPLICABLE PR DUCT D CUMENTATI N AS BEING
C MPATIBLE. D-LINK ’S  BLIGATI N UNDER THIS WARRANTY SHALL BE A REAS NABLE EFF RT T PR VIDE
C MPATIBILITY, BUT D-LINK SHALL HAVE N  BLIGATI N T PR VIDE C MPATIBILITY WHEN THERE IS FAULT
IN THE THIRD-PARTY HARDWARE  R S FTWARE. D-LINK MAKES N WARRANTY THAT  PERATI N  F ITS
S FTWARE PR DUCTS WILL BE UNINTERRUPTED  R ABS LUTELY ERR R-FREE, AND N WARRANTY THAT ALL
DEFECTS IN THE S FTWARE PR DUCT, WITHIN  R WITH UT THE SC PE  F D-LINK ’S APPLICABLE PR DUCT
D CUMENTATI N, WILL BE C RRECTED.
D-Link Offices for Registration and Warranty Service
THE PRODUCT’S REGISTRATION CARD, PROVIDED AT THE BACK OF THIS MANUAL, MUST BE SENT TO A D-LINK
OFFICE. TO OBTAIN AN RMA NUMBER FOR WARRANTY SERVICE AS TO A HARDWARE PRODUCT, OR TO OBTAIN
WARRANTY SERVICE AS TO A SOFTWARE PRODUCT, CONTACT THE D-LINK OFFICE NEAREST YOU. AN
ADDRESS/TELEPHONE/FAX/E-MAIL/WEB SITE LIST OF D-LINK OFFICES IS PROVIDED IN THE BACK OF THIS MANUAL.

v
LIMITATION OF WARRANTIES
IF THE D-LINK PR DUCT D ES N T  PERATE AS WARRANTED AB VE, THE CUST MER’S S LE REMEDY SHALL
BE, AT D-LINK ’S  PTI N, REPAIR  R REPLACEMENT. THE F REG ING WARRANTIES AND REMEDIES ARE
EXCLUSIVE AND ARE IN LIEU  F ALL  THER WARRANTIES, EXPRESSED  R IMPLIED, EITHER IN FACT  R BY
 PERATI N  F LAW, STATUT RY  R  THERWISE, INCLUDING WARRANTIES  F MERCHANTABILITY AND
FITNESS F R A PARTICULAR PURP SE. D-LINK NEITHER ASSUMES N R AUTH RIZES ANY  THER PERS N T
ASSUME F R IT ANY  THER LIABILITY IN C NNECTI N WITH THE SALE, INSTALLATI N MAINTENANCE  R USE
FD-LINK’SPRDUCTS
D-LINK SHALL N T BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATI N DISCL SE THAT THE
ALLEGED DEFECT IN THE PR DUCT D ES N T EXIST  R WAS CAUSED BY THE CUST MER’S  R ANY THIRD
PERS N’S MISUSE, NEGLECT, IMPR PER INSTALLATI N  R TESTING, UNAUTH RIZED ATTEMPTS T REPAIR,  R
ANY  THER CAUSE BEY ND THE RANGE  F THE INTENDED USE,  R BY ACCIDENT, FIRE, LIGHTNING  R  THER
HAZARD.
LIMITATION OF LIABILITY
IN N EVENT WILL D-LINK BE LIABLE F R ANY DAMAGES, INCLUDING L SS  F DATA, L SS  F PR FITS, C ST  F
CVERRTHERINCIDENTAL,CNSEQUENTIALRINDIRECTDAMAGESARISINGUTTHEINSTALLATIN,
MAINTENANCE, USE, PERF RMANCE, FAILURE  R INTERRUPTI N  F A D- LINK PR DUCT, H WEVER CAUSED
AND  N ANY THE RY  F LIABILITY. THIS LIMITATI N WILL APPLY EVEN IF D-LINK HAS BEEN ADVISED  F THE
P SSIBILITY  F SUCH DAMAGE.
IF Y U PURCHASED A D-LINK PR DUCT IN THE UNITED STATES, S ME STATES D N T ALL W THE LIMITATI N
 R EXCLUSI N  F LIABILITY F R INCIDENTAL  R C NSEQUENTIAL DAMAGES, S THE AB VE LIMITATI N MAY
N T APPLY T Y U.
Trademarks
Copyright

2000 D-Link Corporation.
Contents subject to change without prior notice.
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc.
All other trademarks belong to their respective proprietors.
Copyright Statement
No part of this publication may be reproduced in any form or by any means or used to make any derivative
such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link
Systems Inc., as stipulated by the United States Copyright Act of 1976
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
!Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Requirements
To ensure compliance with FCC RF exposure requirements, the antenna used for
this device must be installed to provide a separation distance of at least 20 cm
from all persons and must not be co-located or operating in conjunction with any
other antenna or radio transmitter. Installers and end-users must follow the
installation instructions provided in this user guide.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as the 2 conditions above are met, further transmitter testing will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and
Obtaining a separate FCC authorization.
This product limit antenna type to use KWF-144-120 ,KWF-613C-120 and KN-813A-120-1

vii
End Product Labelling
This transmitter module is authorized only for use in devices where the antenna may be installed such
that 20 cm may be maintained between the antenna and users (for example access points, routers,
wireless ASDL modems, and similar equipment). The final end product must be labeled in a visible
area with the following: “ Contains TX FCC ID: KA22002020012-1 ”.
Manual Information That Must be Included
The users manual for end users must include the following information in a prominent location “
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for
this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference in which case
the user may be required to take adequate measures.
VCCI Class B Warning
Remark：
：：
：
The module has been passed the module approval testing by FCC. It's can only used with the
antenna that we tested in other system. The host system should have a label on the outside that
shows the module's FCC ID.

ix
Notices
NOTE: This message denotes neutral or positive information that calls out
important points to the text. A note provides information that may apply only
in special cases.
CAUTION: Cautions call special attention to hazards that can cause system
damage or data corruption, to a lesser degree than warnings.
WARNING: Warnings call special attention to hazards that can cause
system damage, data corruption, personal injury, or death.

Contents
List of Figures........................................................xv
List of Tables........................................................xvii
Preface...................................................................xix
About this Document..................................................................................... xix
Audience.........................................................................................................xx
Additional Resources......................................................................................xx
1 Introduction...........................................................1-1
Package Contents.........................................................................................1-1
System Requirements...................................................................................1-2
Hardware Installation.............................................................................................1-2
2 Windows 2000.......................................................2-1
Driver Installation (First-time Install)..............................................................2-1
Driver Installation (Previous Driver Installed)................................................2-5
Driver Uninstallation ....................................................................................2-14
Device Configuration...................................................................................2-17
Infrastructure Mode...............................................................................2-22
Ad Hoc Mode.........................................................................................2-23
TCP/IP Setup ........................................................................................2-24

3 Windows Millennium Edition............................... 3-1
Driver Installation.......................................................................................... 3-1
Driver Uninstallation...................................................................................... 3-5
Device Configuration .................................................................................... 3-7
Infrastructure Mode ................................................................................ 3-9
Ad Hoc Mode........................................................................................ 3-10
TCP/IP Configuration............................................................................3-12
4 Windows 98 Second Edition ............................... 4-1
Driver Installation.......................................................................................... 4-1
Driver Uninstallation...................................................................................... 4-5
Device Configuration .................................................................................... 4-8
Infrastructure Mode ................................................................................ 4-9
Ad Hoc Mode........................................................................................ 4-11
TCP/IP Setup........................................................................................ 4-13
5 Windows XP.......................................................... 5-1
Driver Installation (First-time Install).............................................................5-1
Driver Uninstallation...................................................................................... 5-6
Device Configuration ..................................................................................5-10
Infrastructure Mode ..............................................................................5-12
Ad Hoc Mode........................................................................................ 5-13
TCP/IP Setup........................................................................................ 5-15
Windows XP Wireless Network Configuration ........................................... 5-20
Infrastructure Mode ..............................................................................5-22
Ad hoc mode ........................................................................................ 5-24
Connect to an Available Wireless Network..........................................5-26
6 Windows NT 4.0.................................................... 6-1
Driver Installation and TCP/IP Setup............................................................ 6-1
Device Configuration .................................................................................... 6-7

Infrastructure Mode.................................................................................6-8
Ad Hoc Mode.........................................................................................6-11
Verify Connection..................................................................................6-13
Driver Uninstallation ....................................................................................6-15
7 LinkMon.................................................................7-1
Installation......................................................................................................7-1
Features.........................................................................................................7-5
8 RFSilent.................................................................8-1
System Requirements...................................................................................8-1
Windows 98SE Environment...................................................................8-1
RFSilent Setup ..............................................................................................8-2
Operation.......................................................................................................8-2
9 Country Code Selector.........................................9-1
10 Troubleshooting..................................................10-2

List of Figures
Figure 2-1. Infrastructure Mode ...............................................................2-17
Figure 2-2. Ad Hoc Mode.........................................................................2-18
Figure 8-1. RFSilent Icon...........................................................................8-2
Figure 8-2. RFSilent Menu Selections.......................................................8-2

List of Tables
Table 8-1. RFSilent Menu Descriptions....................................................8-3

Preface
This user’s guide provides the necessary information for first-time users to
successfully install the D-Link Network Driver Interface Specification (NDIS)
driver, for the purpose of evaluating and/or operating the D-Link WMP-A12
Station Reference Design in a Microsoft Windows environment. This guide
also provides information for users who wish to upgrade the D-Link NDIS
driver from previous releases.
This guide describes the steps required to install NDIS drivers for the D-Link
WMP-A12 Wireless Network mini PCI Card in Windows 2000, Windows
Millennium Edition, Windows 98 Second Edition, Windows XP, and Windows
NT 4.0. This guide also includes detailed instructions for configuring the PC
Card device, or IEEE 802.11a station (STA), to interact with an access point
(AP) in infrastructure mode and with other STAs in ad hoc mode. Instructions
for installing or upgrading the diagnostic utility LinkMon are also included.
You should also read this before proceeding to install the D-Link WMP-A12
Wireless Network mini PCI Card and NDIS driver in the targeted operating
system (OS) environment.
About this Document
The document consists of the following chapters and appendixes:
Chapter 1 Introduction—Hardware, Software, and System
Requirements needed to setup D-Link WMP-A12 Station
Reference Design.
Chapter 2 Windows 2000—Installation/Uninstallation Procedures and
Device/Network Configurations for Windows 2000.
Chapter 3 Windows Millennium Edition—Installation/Uninstallation
Procedures and Device/Network Configurations for Windows
Millennium Edition.
Chapter 4 Windows 98 Second Edition—Installation/Uninstallation
Procedures and Device/Network Configurations for Windows
98 Second Edition.
Chapter 5 Windows XP—Installation/Uninstallation Procedures and
Device/Network Configurations for Windows XP.

Chapter 6 Windows NT 4.0—Installation/Uninstallation Procedures
and Device/Network Configurations for Windows NT 4.0.
Chapter 7 LinkMon—Graphical User Interface for Operational Status
and Statistics of D-Link WMP-A12 Station Reference
Design.
Chapter 8 RFSilent—RFSilent application that allows you to enable or
disable the RF Signal (radio) on all D-Link STA Reference
Designs.
Chapter 9 Country Code Selector—Utility for selecting countries’
regulatory domains, FCC (USA and Canada) and TELEC
(Japan).
Chapter 10 Troubleshooting—Hints on fixing common
Installation/Uninstallation and Device/Network
Configurations issues.
Audience
This document is intended for D-Link customers who wish to install and
evaluate the D-Link WMP-A12 Station Reference Design in the supported
Microsoft Windows environments.
Additional Resources
D-Link STA Reference Design hardware, software, and documentation
contain proprietary information of D-Link Communications, Inc., and are
provided under a license agreement containing restrictions on use and
disclosure, and are also protected by copyright law. Reverse engineering of
this hardware, software, or documentation is prohibited.
The following resources should be referenced regarding topics that are not
addressed in this document:
"AR5111 Radio-on-a-Chip for 5-GHz Wireless LANs data sheet
"AR5211 MAC/Baseband Processor for IEEE 802.11a 5-GHz Wireless
LAN data sheet
"AP User’s Guide
"STA Reference Design Functional Specification