D-Link DCS-5230 User manual

2D-Link DCS-5230 User Manual
Table of Contents
Product Overview ........................................................ 3
Package Contents ................................................... 3
System Requirements ............................................. 3
Introduction .............................................................. 4
Hardware Overview ................................................. 5
Front .................................................................. 5
Left Panel........................................................... 6
Right Panel ........................................................ 7
Bottom Panel ..................................................... 8
Rear Panel......................................................... 9
Hardware Installation ............................................. 10
DI/DO Input Specications ....................................... 13
Wireless Installation Considerations...................... 14
Conguration............................................................. 15
D-Link Setup Wizard.............................................. 15
Enabling UPnP for Windows®XP .......................... 16
Setting up a Wireless Connection with WPS......... 21
Testing the DCS-5230 ........................................... 22
Viewing Your DCS-5230........................................ 23
Using the DCS-5230 with an Internet Browser...... 24
Live Video ........................................................ 25
DCS-5230 Conguration ....................................... 27
Setup ............................................................... 27
Maintenance .................................................... 46
Status............................................................... 50
Help ................................................................. 52
D-ViewCam Installation............................................. 53
Adding a Camera................................................... 56
Wireless Security....................................................... 61
What is WEP? .......................................................61
What is WPA? .......................................................62
Using & Conguring the DCS-5230 with a NAT
Router.................................................................... 63
Router Set-Up and Installation......................... 67
Using & Conguring 3G Compatible Cell Phones . 70
Play from RealPlayer ....................................... 71
Play from PVPlayer.......................................... 76
Troubleshooting ........................................................ 79
Wireless Basics ......................................................... 82
Networking Basics .................................................... 87
Check your IP Address.......................................... 87
Statically Assign an IP Address............................. 88
Technical Specications........................................... 89
Table of Contents

3D-Link DCS-5230 User Manual
Section 1 - Product Overview
• D-Link DCS-5230 Wireless N PTZ Network Camera
• CAT5 Ethernet Cable
• Power Adapter
• Manual and Software on CD
• Quick Install Guide
• Camera Stand
• Mounting Screws
Note: Using a power supply with a different voltage than the one included with
your product will cause damage and void the warranty for this product.
If any of the above items are missing, please contact your reseller.
System Requirements
• Windows®2000 or XP
• At least 256MB of memory (512MB recommended)
• A wireless (802.11n or 802.11g) or Ethernet network
• Internet Explorer 6.x or higher Internet Web Browser
• VGA card resolution: 800x600 or above
• CPU: 1.3GHz or above processor (2.4GHz processor or higher with 512MB memory and a 32MB
video card is required for multiple camera viewing and recording in IP surveillance program)
Product Overview
Package Contents

4D-Link DCS-5230 User Manual
Section 1 - Product Overview
Introduction
D-Link’s 1.3 Megapixel DCS-5230 is a 802.11n (draft) wireless ptz network camera designed with home and SOHO
users in mind. The DCS-5230 delivers high quality real-time videos in MPEG-4 and JPEG allowing optimization for
both image quality and bandwidth-efciency.
The 1 Lux CMOS sensor ideal for low-light conditions and a built-in infrared LED for night surveillance allows this camera
to provide 24-hour real-time monitoring. The motorized pan/tilt controls with 16x digital zoom offer precision close up
imaging. A built-in PIR sensor provides effective motion detection capabilities. The WPS button offers a secure and
easy wireless connection setup.
The DCS-5230 features 3G mobile video support, enabling users to view a live video feed from their camera on a
compatible 3G mobile phone or PDA anywhere in a 3G coverage area. This allows users to remotely monitor the
camera without having to use a computer. D-ViewCam, IP video management software is also included to manage up
to 32 cameras simultaneously from your computer, send automated e-mail alerts, and record video to your hard drive
when motion is detected.

5D-Link DCS-5230 User Manual
Section 1 - Product Overview
Hardware Overview
Microphone
This built-in microphone can be used capture audio
from sources nearby the camera.
Camera Dome
This clear dome houses the camera lens and
protects the pan/tilt/zoom apparatus.
Front
Pyroelectric Infrared (PIR) Sensor
This sensor is used to detect motion based on
temperature variations within the immediate area.
Infrared LEDs
LEDs enclosed in the dome illuminate the camera’s
eld of vision during low-light operation.

6D-Link DCS-5230 User Manual
Section 1 - Product Overview
WPS Button
Press this button to establish a WPS connection.
MicroSD Slot
Insert a standard MicroSD card into this slot for image storage.
WPS LED
The WPS LED will blink blue when initializing a connection, and
illuminate with solid blue once the connection has been established.
Power/Link LED
The Power LED will illuminate red when the power is turned on. The
light will remain red until the it has been initialized. The Link LED will
illuminate green once a connection is established.
Left Panel

7D-Link DCS-5230 User Manual
Section 1 - Product Overview
DC Power Connector
The DC Power input connector is labeled DC 12V with a single jack
socket to supply power to the DCS-5230.
Ethernet Cable Connector
The DCS-5230 features a RJ-45 connector for connections to 10Base-T
Ethernet cabling or 100Base-TX Fast Ethernet cabling. The port
supports the NWay protocol, allowing the DCS-5230 to automatically
detect or negotiate the transmission speed of the network.
Digital I/O Connector
Connect a digital I/O device to this pin block.
Audio Out
Connect a 3.5mm audio cable for output to a speaker.
Right Panel

8D-Link DCS-5230 User Manual
Section 1 - Product Overview
Bottom Panel
Mounting Socket
The silver mounting stand can be connected here if needed.
Reset Button
Depress this button with a straightened paper clip
for about 20 seconds to reset the camera to factory
default settings.

9D-Link DCS-5230 User Manual
Section 1 - Product Overview
Mounting Slots
These slots can be used to mount the camera against
a wall using protruding bolts, nails, or screws.
Mounting Stand
This stand can be mounted atop or on the bottom of the
enclosure depending on the camera’s orientation.
Rear Panel

10D-Link DCS-5230 User Manual
Section 1 - Product Overview
Hardware Installation
Standard Orientation
Attach the silver mounting stand above the dome of the camera.
Tighten the nut on the top of the mounting stand using a coin or a screwdriver.
Inverted Orientation
Set the mounting onto a at surface. Slide the camera down vertically onto the stand.

11D-Link DCS-5230 User Manual
Section 1 - Product Overview
Cable Installation
Connect an Ethernet cable to the Ethernet port located on the camera’s back panel
and attach it to the network.
Note: An Ethernet cable is required during initial setup. Once your wireless configuration
has been set up, you may disconnect the Ethernet cable and begin communicating
wirelessly with your DCS-5230.
Attach the external power supply to the DC power input connector located on the
camera’s side panel, and connect the adapter to an AC power outlet.
Connect the 3.5mm audio connector from a speaker to the Audio Out port.

12D-Link DCS-5230 User Manual
Section 1 - Product Overview
MicroSD Card Installation
Locate the MicroSD slot on the side of the camera.
Push a MicroSD card into the slot until it clicks into place.
Note: To remove a MicroSD card, gently push the card in and it will eject.

13D-Link DCS-5230 User Manual
Section 1 - Product Overview
As the Digital Input signal is controlled by an external device, we recommend that you set your device to feed no current
normally, and feed a 12V current only to trigger a DI event on the DCS-5230.
Example use of DI/DO:
You can connect a motion sensor to the DI port, signaling the camera to take a snapshot and to trigger an alarm
connected to the DO port.
DI: Receives signals from an outside sensor. Connect any external security device to the DI port.
DO: Triggers an output device such as a buzzer or alarm.
Note: External device ports connected to the DI or DO port must provide 12V power.
DI/DO Input Specifications
DO (Digital Output):
Normal: Open circuit
Trigger: Short circuit
After powering on or rebooting the DCS-5230,
the camera will be in Normal mode by default.
DI (Digital Input):
Normal: No current
Trigger: 12V current
Camera External Device

14D-Link DCS-5230 User Manual
Section 2 - Installation
Wireless Installation Considerations
The DCS-5230 can be accessed using a wireless connection from virtually anywhere within the operating range of your
wireless network. Keep in mind, however, that the quantity, thickness and location of walls, ceilings, or other objects
that the wireless signals must pass through, may limit the range. Ranges vary depending on the types of materials and
background RF (radio frequency) noise in your home or ofce. The key to maximizing the wireless range is to follow
these basic guidelines:
1. Minimize the number of walls and ceilings between the D-Link router and other network devices. Each
wall or ceiling can reduce your adapter’s range from 3 to 90 feet (1 to 30 meters).
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet
(14 meters) thick. Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.
3. Try to position access points, wireless routers, and computers so that the signal passes through open
doorways and drywall. Materials such as glass, metal, brick, insulation, concrete and water can affect
wireless performance. Large objects such as sh tanks, mirrors, le cabinets, metal doors and aluminum
studs may also have a negative effect on range.
4. Keep your product at least 3 to 6 feet (1-2 meters) away from electrical devices or appliances that
generate RF noise.
5. If you are using 2.4GHz cordless phones, make sure that the 2.4GHz phone base is as far away from
your wireless device as possible. The base transmits a signal even if the phone in not in use. In some
cases, cordless phones, X-10 wireless devices, and electronic equipment such as ceiling fans, uorescent
lights, and home security systems may dramatically degrade wireless connectivity.

15D-Link DCS-5230 User Manual
Section 3 - Configuration
D-Link Setup Wizard
DCC will show the MAC address and IP address of your DCS-5230. If you have a DHCP* server on your network,
there will be a valid IP Address displayed at the end of DCC process. You can begin to use the IP camera now.
*A DHCP server is a device that supplies IP Addresses to its clients that are on the same network.
Configuration
Turn on the computer and Insert the D-Link DCS-5230 Driver CD in the CD-ROM drive. The step-by-step instructions
will help you to search and setup your IP camera smoothly and quickly.
If the CD Autorun function does not automatically start on your computer, click Windows® Start > Run. In the Run
command box type “D:\DCS-5230.exe”, where D: represents the drive letter of your CD-ROM. If it does start, proceed
to the next screen.
Click Start

16D-Link DCS-5230 User Manual
Section 3 - Configuration
UPnP (Universal Plug and Play) is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. The
DCS-5230 is an UPnP enabled Internet camera. If your operating system is
UPnP enabled, the device will be easier to congure. If you do not want to use
the UPnP functionality, it can be disabled by unchecking the Enabled UPnP
checkbox on the Advanced > Network page (see page 29). Use the following
steps to enable UPnP settings only if you are running Windows®XP. If you are
running Windows®98/2000, UPnP is not available.
Go to Start > Settings. Click Control Panel.
Enabling UPnP for Windows®XP
Click Add or Remove Programs

17D-Link DCS-5230 User Manual
Section 3 - Configuration
The following screen will appear.
Select Networking Services.
Select Universal Plug and Play.
Click Details
Click Add/Remove Windows Components
Click OK

18D-Link DCS-5230 User Manual
Section 3 - Configuration
Please wait while Setup congures the components.
Click Next
Click Finish

19D-Link DCS-5230 User Manual
Section 3 - Configuration
To view your DCS-5230 Internet Camera in an Internet browser, go
to your Desktop and click My Network Places.
Click DCS-5230 (192.168.0.120).

20D-Link DCS-5230 User Manual
Section 3 - Configuration
After you click on the DCS-5230 icon, your Internet browser will automatically be opened to the IP Address of the
DCS-5230, in this example it is: http://192.168.0.120. Your DCS-5230 may have a different IP Address.
http://192.168.0.120/eng/index.cgi