D-Link DGS-1210-10P User manual

Table of Contents D-Link Web Smart Switch User Manual
i
i
Table of Contents
Table of Contents ............................................................................................................................................. i
About This Guide............................................................................................................................................. 1
Terms/Usage.................................................................................................................................................. 1
Copyright and Trademarks ............................................................................................................................ 1
1 Product Introduction................................................................................................................................... 2
DGS-1210-10P............................................................................................................................................... 3
Front Panel................................................................................................................................................. 3
Rear Panel.................................................................................................................................................. 3
DGS-1210-20................................................................................................................................................. 3
Front Panel................................................................................................................................................. 4
Rear Panel.................................................................................................................................................. 4
DGS-1210-28................................................................................................................................................. 4
Front Panel................................................................................................................................................. 4
Rear Panel.................................................................................................................................................. 5
DGS-1210-28P............................................................................................................................................... 5
Front Panel................................................................................................................................................. 5
Rear Panel.................................................................................................................................................. 5
DGS-1210-52................................................................................................................................................. 5
Front Panel................................................................................................................................................. 6
Rear Panel.................................................................................................................................................. 6
2 Hardware Installation .................................................................................................................................. 7
Step 1: Unpacking.......................................................................................................................................... 7
Step 2: Switch Installation.............................................................................................................................. 7
Desktop or Shelf Installation....................................................................................................................... 7
Rack Installation......................................................................................................................................... 7
Step 3 – Plugging in the AC Power Cord....................................................................................................... 8
Power Failure ............................................................................................................................................. 9
3 Getting Started........................................................................................................................................... 10
Management Options................................................................................................................................... 10
Using Web-based Management .................................................................................................................. 10
Supported Web Browsers ........................................................................................................................ 10
Connecting to the Switch.......................................................................................................................... 10
Login Web-based Management............................................................................................................... 11
Smart Wizard ............................................................................................................................................... 11
Web-based Management............................................................................................................................. 11
SmartConsole Utility..................................................................................................................................... 11
4 SmartConsole Utility ................................................................................................................................. 13
SmartConsole Settings ................................................................................................................................ 13
Utility Settings........................................................................................................................................... 13
Log............................................................................................................................................................ 13
Trap .......................................................................................................................................................... 14
Monitor List............................................................................................................................................... 15
About ........................................................................................................................................................ 15
Device Configuration.................................................................................................................................... 15
Add(+), Delete(-) and Discover the device............................................................................................... 17
Device List.................................................................................................................................................... 18
5 Configuration ............................................................................................................................................. 20

Table of Contents D-Link Web Smart Switch User Manual
i
ii i
Smart Wizard Configuration......................................................................................................................... 20
IP Information........................................................................................................................................... 20
Password.................................................................................................................................................. 20
SNMP ....................................................................................................................................................... 21
Web-based Management............................................................................................................................. 23
Tool Bar > Save Menu................................................................................................................................. 24
Save Configuration................................................................................................................................... 24
Save Log .................................................................................................................................................. 24
Tool Bar > Tool Menu .................................................................................................................................. 24
Reset ........................................................................................................................................................ 24
Reset System........................................................................................................................................... 24
Reboot Device.......................................................................................................................................... 24
Configuration Backup and Restore .......................................................................................................... 25
Firmware Backup and Upgrade................................................................................................................ 25
Tool Bar > Smart Wizard.............................................................................................................................. 26
Tool Bar > Online Help................................................................................................................................. 26
Function Tree............................................................................................................................................... 28
Device Information.................................................................................................................................... 28
System > System Settings ....................................................................................................................... 29
System > IPv6 System Settings............................................................................................................... 30
System > IPv6 Route Settings.................................................................................................................. 30
System > IPv6 Neighbor Settings ............................................................................................................ 31
System > Password.................................................................................................................................. 31
System > Port Settings............................................................................................................................. 32
System > DHCP Auto Configuration ........................................................................................................ 32
System > SysLog Host............................................................................................................................. 33
System > Time Profile .............................................................................................................................. 33
System > Power Saving........................................................................................................................... 34
System > IEEE802.3az EEE Settings...................................................................................................... 34
VLAN > 802.1Q VLAN.............................................................................................................................. 35
VLAN > 802.1Q VLAN PVID .................................................................................................................... 36
VLAN > 802.1Q Management VLAN........................................................................................................ 36
VLAN > Voice VLAN > Voice VLAN Global Settings ............................................................................... 36
VLAN > Voice VLAN > Voice VLAN Port Settings ................................................................................... 38
VLAN > Voice VLAN > Voice Device List................................................................................................. 38
VLAN > Auto Surveillance VLAN Settings ............................................................................................... 38
L2 Functions > Jumbo Frame................................................................................................................... 39
L2 Functions > Port Mirroring................................................................................................................... 40
L2 Functions > Loopback Detection......................................................................................................... 40
L2 Functions > MAC Address Table > Static MAC.................................................................................. 41
L2 Functions > MAC Address Table > Dynamic Forwarding Table......................................................... 41
L2 Functions > Spanning Tree > STP Global Settings ............................................................................ 41
L2 Functions > Spanning Tree > STP Port Settings ................................................................................ 43
L2 Functions > Link Aggregation > Port Trunking.................................................................................... 44
L2 Functions > Link Aggregation > LACP Port Settings .......................................................................... 44
L2 Functions > Multicast > IGMP Snooping............................................................................................. 45
L2 Functions > Multicast > Multicast Forwarding..................................................................................... 46
L2 Functions > Multicast > Multicast Filtering Mode ................................................................................ 47
L2 Functions > SNTP > Time Settings..................................................................................................... 47

Table of Contents D-Link Web Smart Switch User Manual
iii
L2 Functions > SNTP > TimeZone Settings............................................................................................. 48
L2 Functions > LLDP > LLDP Global Settings......................................................................................... 49
L2 Functions > LLDP > LLDP MED Settings ........................................................................................... 49
L2 Functions > LLDP > LLDP Port Settings............................................................................................. 50
L2 Functions > LLDP > 802.1 Extension TLV.......................................................................................... 51
L2 Functions > LLDP > 802.3 Extension TLV.......................................................................................... 51
L2 Functions > LLDP > LLDP Management Address Settings................................................................ 52
L2 Functions > LLDP > LLDP Management Address Table.................................................................... 52
L2 Functions > LLDP > LLDP Local Port Table ....................................................................................... 53
L2 Functions > LLDP > LLDP Remote Port Table ................................................................................... 54
L2 Functions > LLDP > LLDP Statistics................................................................................................... 55
QoS > Bandwidth Control......................................................................................................................... 56
QoS > 802.1p/DSCP/ToS......................................................................................................................... 57
QoS > IPv6 Traffic Class Priority Settings................................................................................................ 58
QoS > TCP/UDP Port Priority Settings .................................................................................................... 58
Security > Trusted Host............................................................................................................................ 58
Security > Port Security............................................................................................................................ 59
Security > Traffic Segmentation............................................................................................................... 59
Security > Safeguard Engine.................................................................................................................... 60
Security > Storm Control.......................................................................................................................... 60
Security > ARP Spoofing Prevention ....................................................................................................... 60
Security > DHCP Server Screening ......................................................................................................... 61
Security > SSL Settings............................................................................................................................ 61
Security > Smart Binding > Smart Binding Settings................................................................................. 62
Security > Smart Binding > Smart Binding............................................................................................... 63
Security > Smart Binding > White List...................................................................................................... 63
Security > Smart Binding > Black List...................................................................................................... 64
AAA > 802.1X > 802.1X Settings............................................................................................................. 64
ACL > ACL Wizard................................................................................................................................... 66
ACL > ACL Profile List.............................................................................................................................. 67
ACL > ACL Finder .................................................................................................................................... 78
PoE > PoE Global Settings (DGS-1210-10P/28P only)........................................................................... 78
PoE > PoE Port Settings (DGS-1210-10P/28P only)............................................................................... 79
SNMP > Trap to SmartConsole Utility...................................................................................................... 80
SNMP > SNMP > SNMP Global Settings ................................................................................................ 81
SNMP > SNMP > SNMP User ................................................................................................................. 82
SNMP > SNMP > SNMP Group Table..................................................................................................... 82
SNMP > SNMP > SNMP View................................................................................................................. 83
SNMP > SNMP > SNMP Community....................................................................................................... 83
SNMP > SNMP > SNMP Host.................................................................................................................. 84
SNMP > SNMP > SNMP Engine ID......................................................................................................... 84
SNMP > RMON > RMON Global Settings ............................................................................................... 84
SNMP > RMON > RMON Statistics ......................................................................................................... 84
SNMP > RMON > RMON History............................................................................................................. 85
SNMP > RMON > RMON Alarm Settings ................................................................................................ 85
SNMP > RMON > RMON Event............................................................................................................... 86
Monitoring > Port Statistics....................................................................................................................... 86
Monitoring > Cable Diagnostics ............................................................................................................... 87
Monitoring > System Log.......................................................................................................................... 88

Table of Contents D-Link Web Smart Switch User Manual
i
iv v
6 Command Line Interface........................................................................................................................... 89
To connect a switch via TELNET:................................................................................................................ 89
Logging on to the Command Line Interface:................................................................................................ 89
CLI Commands:........................................................................................................................................... 89
?................................................................................................................................................................ 90
download.................................................................................................................................................. 90
upload....................................................................................................................................................... 91
config ipif system...................................................................................................................................... 92
config ipif system...................................................................................................................................... 93
logout........................................................................................................................................................ 93
ping........................................................................................................................................................... 93
ping6......................................................................................................................................................... 94
reboot ....................................................................................................................................................... 95
reset config............................................................................................................................................... 95
show ipif.................................................................................................................................................... 95
show switch .............................................................................................................................................. 96
config account admin password............................................................................................................... 96
save.......................................................................................................................................................... 97
debug info................................................................................................................................................. 97
Appendix A - Ethernet Technology.............................................................................................................. 99
Gigabit Ethernet Technology ....................................................................................................................... 99
Fast Ethernet Technology............................................................................................................................ 99
Switching Technology.................................................................................................................................. 99
Appendix B - Technical Specifications ..................................................................................................... 100
Hardware Specifications ............................................................................................................................ 100
Key Components / Performance ............................................................................................................ 100
Port Functions ........................................................................................................................................ 100
Physical & Environment ......................................................................................................................... 100
Emission (EMI) Certifications................................................................................................................. 100
Safety Certifications................................................................................................................................ 100
Features..................................................................................................................................................... 100
L2 Features ............................................................................................................................................ 100
VLAN ...................................................................................................................................................... 101
QoS (Quality of Service)......................................................................................................................... 101
Security................................................................................................................................................... 101
OAM ....................................................................................................................................................... 101
Management........................................................................................................................................... 101
D-Link Green Technology ...................................................................................................................... 101
Appendix C – Rack mount Instructions .................................................................................................... 103

About This Guide D-Link Web Smart Switch User Manual
1
About This Guide
This guide provides instructions to install the D-Link Gigabit Web Smart Switch DGS-1210-10P/20/28/28P/52,
how to use the SmartConsole Utility, and to configure Web-based Management step-by-step.
Note:T
he model you have purchased may
appear slightly different from the illustrations
shown in the document. Refer to the Product
Instruction and Technical Specification sections
for detailed information about your switch, its
components, network connections, and technical
specifications.
This guide is mainly divided into four parts:
1. Hardware Installation: Step-by-step hardware installation procedures.
2. Getting Started: A startup guide for basic switch installation and settings.
3. Smart Console Utility: An introduction to the central management system.
4. Configuration: Information about the function descriptions and configuration settings.
Terms/Usage
In this guide, the term “Switch” (first letter capitalized) refers to the Smart Switch, and “switch” (first letter
lower case) refers to other Ethernet switches. Some technologies refer to terms “switch”, “bridge” and
“switching hubs” interchangeably, and both are commonly accepted for Ethernet switches.
A NOTE indicates important
information that
helps a better use of the device.
A CAUTION indicates potential property damage
or personal injury.
Copyright and Trademarks
Information in this document is subjected to change without notice.
© 2012 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly
forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft
and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and
trade names other than its own.

1 Product Introduction D-Link Web Smart Switch User Manual
2
1 Product Introduction
Thank you and congratulations on your purchase of D-Link Web Smart Switch Products.
D-Link's next generation Web Smart Ethernet switch series blends plug-and-play simplicity with exceptional
value and reliability for small and medium-sized business (SMB) networking. All models are housed in a new
style rack-mount metal case with easy-to-view front panel diagnostic LEDs, and provides advanced features
including network security, traffic segmentation, QoS and versatile management.
Flexible Port Configurations.The DGS-1210 series is the new generation of Web Smart series. It provides
a variety of port counts- 16, 24 or 48 10/100/1000Mbps ports plus 4 SFP ports. Besides, the series offers 2
PoE models with 8 10/100/1000Mbps PoE ports plus 2 SFP ports and 24 10/100/1000Mbps PoE ports plus 4
SFP ports.
The first 4 ports of DGS-1210-10P/28P also support up to 30 watts PoE power for the connections of PoE +
Power Devices, allowing them to be deployed at difficult places such as on high walls and ceilings, where AC
power outlets are not readily available.
D-Link Green Technology. D-Link Green devices are about providing eco-friendly alternatives without
compromising performance. D-Link Green Technology includes a number of innovations to reduce energy
consumption on DGS-1210 series such as shutting down a port, or turning off some LED indicators, or
adjusting the power usage according to the Ethernet cable connected to it. For PoE model such as DGS-
1210-10P/28P, D-Link Green Technology offers Time-based PoE feature to shut down per port power off
working hours.
Extensive Layer 2 Features. Implemented as complete L2 devices, these switches include functions such
as IGMP snooping, port mirroring, Spanning Tree, 802.3ad LACP and Loopback Detection to enhance
performance and network resiliency.
Traffic Segmentation, QoS and Auto Surveillance VLAN.The switches support 802.1Q VLAN standard
tagging to enhance network security and performance. The switches also support 802.1p priority queues,
enabling users to run bandwidth-sensitive applications such as streaming multimedia by prioritizing that
traffic in network. These functions allow switches to work seamlessly with VLAN and 802.1p traffic in the
network. Auto Surveillance VLAN will automatically place the vedio traffic from pre-defined IP surveillance
devices to an assigned VLAN with higher priority, so it can be separated from normal data traffic. Asymmetric
VLAN is implemented in these switches for a more efficient use of shared resources, such as server or
gateway devices.
Network Security. D-Link’s innovative Safeguard Engine function protects the switches against traffic
flooding caused by virus attacks. Additional features like 802.1X port-based authentication provide access
control of the network with external RADIUS servers. ACL is a powerful tool to screen unwanted IP or MAC
traffic. Storm Control can help to keep the network from being overwhelmed by abnormal traffic. Port
Security is another simple but useful authentication method to maintain the network device integrity.
Versatile Management. The new generation of D-Link Web Smart Switches provides growing businesses
with a simple and easy management of their network, using an intuitive SmartConsole utility or a Web-Based
management interface that allows administrators to remotely control their network down to the port level. The
SmartConsole easily allows customers to discover multiple D-Link web smart switches with the same L2
network segment connected to the user’s local PC. With this utility, users do not need to change the IP
address of the PC and provide easy initial settings of the smart switches. The switches within the same L2
network segment connected to the user’s local PC are displayed on the screen for instant access. It allows
extensive switch configuration settings, and basic configuration of discovered devices, such as a password
change or firmware upgrade.
Users can also access the switch via TELNET. Some basic tasks can be performed such as changing the
Switch IP address, resetting the settings to factory defaults, setting the administrator password, rebooting the
Switch, or upgrading the Switch firmware by using the Command Line Interface (CLI).

1 Product Introduction D-Link Web Smart Switch User Manual
3
3
In addition, users can utilize the SNMP MIB (Management Information Base) to poll the switches for
information about the status, or send out traps of abnormal events. SNMP support allows users to integrate
the switches with other third-party devices for management in an SNMP-enabled environment. D-Link Web
Smart Switches also come with the D-View plug-in module that works with D-View 6 SNMP Management
Software, and provides easy-to-use graphic interface and facilitates the operation efficiency.
DGS-1210-10P
8-Port 10/100/1000Mbps plus 2 combo ports of 1000Base-T/SFP ports Web Smart PoE Switch.
Front Panel
Figure 1.1 – DGS-1210-10P Front Panel
Power LED :The Power LED lights up when the Switch is connected to a power source.
Pwr Max: The Pwr Max LED lights up when the Switch reaches the maximum power budget defined by the
administrator via PoE System Settings page of Web GUI or the default power budget of 78 Watts.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration
and all changes will be lost.
Mode: By pressing the Mode button, the Port LED will switch between Link/Act and PoE modes.
Port Link/Act/Speed LED (1-8, 9T, 10T 9F, 10F): When mode LED lights up in Link/Act mode, the port
LEDs indicate a network link through the corresponding port. Blinking indicates the Switch is either sending
or receiving data to the port. When the port LED glows in amber, it indicates the port is running on 10M or
100M. When the port LED glows in green, it is running on 1000Mbps.
CAUTION: The MiniGBIC ports should use UL
listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
CAUTION: The ITE is to be connected only to PoE networks
without routing to the outside plant.
Port PoE LED (1-8): When mode LED lights up in PoE mode, the port LEDs indicate powering status over
the corresponding port. DGS-1210-10P can supply up to 30W on port 1- 4, which are marked with black
background color on front panel, for IEEE802.3at compliance PDs.
Rear Panel
Figure 1.2 – DGS-1210-10P Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-20
16-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.
SFP ports for optical transceivers

1 Product Introduction D-Link Web Smart Switch User Manual
4
Front Panel
Figure 1.3 – DGS-1210-20 Front Panel
Power LED :The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-16, 17F, 18F, 19F, 20F): The Link/Act/Speed LED flashes, which indicates a
network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving
data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
CAUTION: The MiniGBIC ports should use UL
listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration
and all changes will be lost.
Rear Panel
Figure 1.4 – DGS-1210-20 Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-28
24-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.
Front Panel
Figure 1.5 – DGS-1210-28 Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-24, 25F, 26F, 27F, 28F): The Link/Act/Speed LED flashes, which indicates a
network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving
data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
Reset: Press the Reset button for 5 seconds to reset the Switch back to the default settings. All previous
changes will be lost.
CAUTION: The MiniGBIC ports should use UL
listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.

1 Product Introduction D-Link Web Smart Switch User Manual
5
5
Rear Panel
Figure 1.6 – DGS-1210-28 Rear Panel
Power: Connect the supplied AC power cable to this port.
DGS-1210-28P
24-Port 10/100/1000Mbps plus 4 SFP ports Web Smart PoE Switch.
Front Panel
Figure 2.7 – DGS-1210-28P Front Panel
Power LED :The Power LED lights up when the Switch is connected to a power source.
Pwr Max: The Pwr Max LED lights up when the Switch reaches the maximum power budget defined by the
administrator via PoE System Settings page of Web GUI or the default power budget of 185 Watts.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration
and all changes will be lost.
Mode: By pressing the Mode button, the Port LED will switch between Link/Act and PoE modes.
Port Link/Act/Speed LED (1-24, 25F, 26F, 27F, 28F): When mode LED lights up in Link/Act mode, the port
LEDs indicate a network link through the corresponding port. Blinking indicates the Switch is either sending
or receiving data to the port. When the port LED glows in amber, it indicates the port is running on 10M or
100M. When the port LED glows in green, it is running on 1000Mbps.
Fan: The Fan LED lights green when fans work well, and lights red when fans fail.
CAUTION: The MiniGBIC ports should use UL
listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
CAUTION: The ITE is to be connected only to PoE networks
without routing to the outside plant.
Port PoE LED (1-24): When mode LED lights up in PoE mode, the port LEDs indicate powering status over
the corresponding port. DGS-1210-28P can supply up to 30W on port 1- 4, which are marked with black
background color on front panel, for IEEE802.3at compliance PDs.
Rear Panel
Figure 1.8 – DGS-1210-28P Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-52
48-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.

1 Product Introduction D-Link Web Smart Switch User Manual
6
Front Panel
Figure 1.9 – DGS-1210-52 Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-48, 49F, 50F, 51F, 52F): The Link/Act/Speed LED flashes, which indicates a
network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving
data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
Fan: The Fan LED lights green when fans work well, and lights red when fans fail.
Reset: Press the Reset button for 5 seconds to reset the Switch back to the default settings. All previous
changes will be lost.
CAUTION: The MiniGBIC ports should use UL
listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
Rear Panel
Figure 1.10 – DGS-1210-52 Rear Panel
Power: Connect the supplied AC power cable to this port.

2 Hardware Installation D-Link Web Smart Switch User Manual
7
7
2 Hardware Installation
This chapter provides unpacking and installation information for the D-Link Web-Smart Switch.
Step 1: Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the
User Manual to make sure all items are present and undamaged. If any item is missing or damaged, please
contact your local D-Link reseller for replacement.
One D-Link Web-Smart Switch
One AC power cord
Four rubber feet
Screws and two mounting brackets
One Multi-lingual Getting Started Guide
One CD with User Manual, SmartConsole Utility program, and D-View Module
If any item is found missing or damaged, please contact the local reseller for replacement.
Step 2: Switch Installation
For safe switch installation and operation, it is recommended that you:
Visually inspect the power cord to see that it is secured fully to the AC power connector.
Make sure that there is proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch.
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached
on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and
the objects around it.
Figure 2.1 – Attach the adhesive rubber pads to the bottom
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack, which can be placed in a wiring closet with
other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and
secure them with the screws provided (please note that these brackets are not designed for palm size
switches).
Figure 2.2 – Attach the mounting brackets to the Switch

2 Hardware Installation D-Link Web Smart Switch User Manual
8
Then, use the screws provided with the equipment rack to mount the switch in the rack.
Figure 2.3 – Mount the Switch in the rack or chassis
Please be aware of following safety Instructions when installing:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore, consideration should be
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma)
specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit, and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch circuit (e.g. use
of power strips)."
Step 3 – Plugging in the AC Power Cord
Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably
one that is grounded and surge protected).
Figure 2.4 –Plugging the switch into an outlet

2 Hardware Installation D-Link Web Smart Switch User Manual
9
9
Power Failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the
switch back in.

3 Getting Started D-Link Web Smart Switch User Manual
10
3 Getting Started
This chapter introduces the management interface of D-Link Web-Smart Switch.
Management Options
The D-Link Web Smart Switch can be managed through any port on the device by using the Web-based
Management, or through any PC using the SmartConsole Utility.
Each switch must be assigned its own IP Address, which is used for communication with the Web-Based
Management or a SNMP network manager. The PC should have an IP address in the same range as the
switch. Each switch can allow up to four users to access the Web-Based Management concurrently.
However, if you want to manage multiple D-Link Web Smart Switches, the SmartConsole Utility is a more
convenient choice. By using the SmartConsole Utility, you do not need to change the IP address of your PC
and it is easier to initialize multiple Smart Switches.
Please refer to the following installation instructions for the Web-based Management and the SmartConsole
Utility.
Using Web-based Management
After a successful physical installation, you can configure the Switch, monitor the network status, and display
statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web browsers:
Internet Explorer 6 or later version
Netscape 8 or later version
Firefox 3.0 or later version
Chrome 5.0 or later version
Safari 4.0 or later version
Opera 10 or later version
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the
PC.
Figure 3.1 – Connected Ethernet cable

3 Getting Started D-Link Web Smart Switch User Manual
1
11 1
Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the
same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have
an IP address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and
a subnet mask of 255.0.0.0. There are two ways to launch the Web-based Management, you may either click
the Web Access button at the top of the SmartConsole Utility or open the web browser and enter 10.90.90.90
(the factory-default IP address) in the address bar. Then press <Enter>.
Figure 3.2 –Enter the IP address 10.90.90.90 in the web browser
NOTE:The switch's factory default IP address is
10.90.90.90 with a subnet mask of 255.0.0.0 and
a default gateway of 0.0.0.0.
The web configuration can also be accessed through the SmartConsole Utility. Open the SmartConsole
Utility and double-click the switch as it appears in the Monitor List. This will automatically load the web
configuration in your web browser.
When the following logon dialog box appears, enter the password and choose the language of the Web-
based Management interface then click OK.
The switch supports 10 languages including English, Traditional Chinese, Simplified Chinese, German,
Spanish, French, Italian, Portuguese, Japanese and Russian. By default, the password is admin and the
language is English.
Figure 3.3 – Logon Dialog Box
Smart Wizard
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart
Switch. Please refer to the Smart Wizard Configuration section for details.
Web-based Management
By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Please
refer to Chapter 5 Configuration for detailed instructions.
SmartConsole Utility
The SmartConsole Utility included in the installation CD is a program for discovering D-Link Smart Switches
within the same network segment connected to your PC. This tool is only for computers running Windows 7,
Vista, XP, or 2000 on both 32/64 bit systems. There are two options for the installation of the SmartConsole
Utility; one is through the autorun program on the installation CD and the other is manual installation.

3 Getting Started D-Link Web Smart Switch User Manual
12
NOTE: Please be sure to uninstall any existing
SmartConsole Utility from your PC before
installing the latest SmartConsole Utility.
Option 1: Follow these steps to install the SmartConsole Utility via the autorun program on the installation
CD.
1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive.
2. The autorun program will appear automatically.
3. Click on the ”Install SmartConsole Utility” button and an installation wizard will guide you through the
process.
4. After successfully installing the SmartConsole Utility, you can open the utility by clicking Start >
Programs > D-Link SmartConsole Utility.
5. Connect the Smart Switch to the same L2 network segment of your PC and use the SmartConsole
Utility to discover the Smart Switches.
Option 2: Follow these steps to install the SmartConsole Utility manually.
1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive.
2. From the Start menu on the Windows desktop, click Computer..
3. In the Run dialog box, type D:\D-Link SmartConsole Utility\D-Link_SmartConsole_Utility_v3.00.10.exe
(where D:\ represents the drive letter of your CD-Rom) and click OK.
4. Follow the on-screen instructions to install the utility.
5. Upon completion, go to Start > Programs > D-Link SmartConsole Utility and open the SmartConsole
Utility.
6. Connect the Smart Switch to the same L2 network segment of your PC and use the SmartConsole
Utility to discover the Smart Switches.
For detailed explanations of SmartConsole’s functions, please refer to Chapter 4 SmartConsole Utility.
NOTE:The current SmartConsole Utility does not
support IPv6 feature. Please be sure to install the
SmartConsole Utility from you PC
with IPv4
address. After installed SmartConsole Utility, then
it can discover the DGS-1210 series with IPv6
address.

4 SmartConsole Utility D-Link Web Smart Switch User Manual
1
13 3
4 SmartConsole Utility
The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link smart switches, which
are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations
of the switch.
The SmartConsole Utility consists of three parts, Device Configurations at the top, Device List as the main
body, and SmartConsole Settings at the left.
Figure 4.1 – SmartConsole Utility
SmartConsole Settings
The SmartConsole Settings at the left has five icons, Utility Settings, Log, Trap, Monitor list, and About.
Utility Settings
Click this icon to launch the Utility Settings window. Refresh time refreshes the devices, which were
selected as monitored devices in the Device List. Choices include 15 secs, 30 secs, 1 mins, 2 mins, and 5
mins for selecting the monitoring time intervals. Utility Group Interval establishes the intervals (in seconds)
that the Switch will be discovered in the SmartConsole Device List.
Figure 4.2 – SmartConsole Utility Settings
NOTE: If the Group Interval is set to 0, IGMP
Snooping must be disabled in the Switch, or the
Web-Smart Switch will not be discovered.
Log
Click this icon to launch the Log window. Click View Log to show the events of the SmartConsole Utility and
the device. Time indicates when the message was received, Location indicates where the message was

4 SmartConsole Utility D-Link Web Smart Switch User Manual
14
received and IP Address denotes where it comes from. Click Refresh to redisplay all log entries, click Clear
to clear all log entries. Click Exit to exit.
Figure 4.3 – SmartConsole Log
Trap
By setting up in “Trap to SmartConsole Utility” in D-Link Web Smart switches, traps can be collected by the
designated host PC with the SmartConsole Utility installed. Click this icon to launch the Trap window. Click
View Trap to show the events of the SmartConsole Utility and the device. Time indicates when the trap
message was received, Location indicates the physical location of the switch that sends out traps, IP
Address denotes where it comes from and Event shows the content of this trap message. Click Refresh to
redisplay all traps, click Clear to clear all entries. Click Exit to exit.
Figure 4.4 – SmartConsole Trap
The trap icon in the SmartConsole Settings will change while receiving new trap messages. Please see
below for detailed description.
Icon Description
No new traps
New traps was received

4 SmartConsole Utility D-Link Web Smart Switch User Manual
1
15 5
Monitor List
By clicking on this icon you will see below options:
Figure 4.5 – SmartConsole Monitor List
Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used.
Save As: Records the setting of the Device List in an appointed filename and file path.
Restore:Manually reload a Device List setting file.
About
Click this icon to launch the SmartConsole Info window.
Figure 4.6 – SmartConsole About
Device Configuration
The Device Configuration in the SmartConsole Utility has five icons:
Device Settings
Password Setting
Firmware Upgrade
DHCP Refresh
Web Access
and the , , device buttons for the Device List.
Device Settings
Select a switch from the Device List. Click on this icon to launch the Device Settings window. Here you can
configure the Product Name, IP Address, Gateway, Subnet Mask, System Name, Location, Trap Host IP,
Switch Group Interval, and DHCP Client Setting of the Switch.
To apply the configuration, insert the correct device password in the Confirm Password box and then click
OK.