Da-Lite SLIMLINE ELECTROL User manual

QUALITY FEATURES FOR BETTER PICTURES,
EASIER OPERATION, LONGER LIFE
• Completely automatic operation…
Flip the switch and built-in adjustable limit
switches control up and down travel.
• Stops in intermediate positions…
for wide screen projection.
• Easily installed…
Fastens to wall or ceiling with two screws or
hooks. Cord plugs into standard outlet
(110-120AC or 220-240AC based on model
ordered).
• Always ready for the show…
No storage problems. Attractive slimline metal
case makes a handsome addition to any room.
• Incomparable picture reproduction…
with Da-Lite’s High Power or Matte White
surface.
• Ideal projection screen…
for family centers, recreation rooms, dens,
clubs, church rooms, offices, classrooms,
small conference rooms.
Printed in U.S.A. 72641 Rev. 1/08
DA-LITE IS MORE
THAN PROJECTION SCREENS
Da-Lite Tripod, Wall and
Ceiling and Electric Screens
Da-Lite Lecterns
Da-Lite
Project-O-Stands
and Easels
Da-Lite
Monitor Mounts
Operating Instructions
for
SLIMLINE ELECTROL®
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: [phone]
800-622-3737
Fax: [phone]
Toll Free Fax: [phone]
www.da-lite.com
e-mail: [email protected]
The Da-Lite Difference.
Visit www.da -lite.com/products/tutorials.php
to find installation and troubleshooting
tutorials. You will also find a link to Live Chat
for interactive support and you can contact us
by email at [email protected] or by phone at
[phone] or [phone] with any
troubleshooting questions.

HANGING BRACKETS
(Optional at extra cost)
No. 6 WALL BRACKET
Non-adjustable permits
screen to extend 6" from
wall.
No. 11 WALL BRACKET
Non-adjustable permits
screen to extend 10" or 14"
from wall.
TO LOWER SCREEN SURFACE
Press lower end of slide switch. Screen will stop in
the “DOWN” position automatically.
TO RAISE SCREEN SURFACE
Press upper end of slide switch. Screen will stop in
the “UP” position automatically.
TO STOP SCREEN
Screen may be stopped in any intermediate
position by positioning slide switch to center
“OFF” position.
NOTE: It is suggested that when screen is not in
use, the slide switch should be positioned to
center “OFF” position.
OPERATING INSTRUCTIONS
3-POSITION SWITCH FOR SLIMLINE
Complete with cable, is standard with the Slimline
Electrol.
SUGGESTED METHODS OF INSTALLATION
CARE OF SCREENS
1. Examine surface to be sure it is free of
insects, dirt or foreign matter before rolling
into case.
2. Screen may be operated as frequently as
necessary but should not be run up and down
continuously. To do so will cause the motor to
overheat and the thermal overload to cut out.
Should this occur, it will be necessary to wait
for the motor to cool sufficiently to resume
operation.
3. Motor does not require lubrication.
NO. 6 WALL BRACKET
NO. 11 WALL BRACKET
PICTURE
SURFACE
PICTURE
SURFACE
PICTURE
SURFACE
PICTURE
SURFACE
WALL
BRACKET
Use No. 6
brackets to
hang from
beam or
valance
CEILING
MOUNTING
Place “D” rings
over hooks well
secured in
ceiling.
WALL
MOUNTING
Slip hanger
eyes over
screws well
secured in wall.
CONCEALED
Allow room for access
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety
precautions should always be followed, including
the following:
1. Read and understand all instructions before
using.
2. Position the cord so that it will not be tripped
over, pulled, or contact hot surfaces.
3. If an extension cord is necessary, a cord with a
current rating at least equal to that of the
appliance should be used. Cords rated for less
amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not
disassemble this appliance. Contact an
authorized service dealer when repair work is
required. Incorrect reassembly can cause
electric shock when the appliance is used
subsequently.
5. The use of an accessory attachment not
recommended by the manufacturer may cause
a risk of fire, electric shock, or injury to
persons.
SAVE THESE
INSTRUCTIONS